Laboratory Technology

The Coating Thickness Gauge is used for the quick and precise detection of layer thicknesses on metals. In comparison to many other paint thickness gauges, this paint thickness gauge does not have to differentiate between ferrous and non-ferrous metal.

- Measuring range PM2.5: 0 ... 500 μg / m³
- Measuring range temperature: -10 ... 50°C / 14 ... 122°F
- Measuring range humidity: 0 ... 99% rh
- Pictograms indicate air quality
- Battery operation
- Micro USB for charging

The heating mantle PCE-HM 1000 is an auxiliary device, which is used in laboratories. The heating mantle helps to heat or control the temperature of different samples or chemicals in the laboratory. The device has a crocheted net inside, in which you can hang the round bottom flask to heat it.

- Power 350 W
- Operating temperature 0 ... +450 °C
- Fast heat-up time
- For round flasks up to 1,000 ml

PCE-EMF 823 is a portable handheld single-axis magnetometer or electromagnetic radiation detector for measuring electromagnetic fields (EMFs). This user-friendly EMF meter is ideal for assessing risks associated with exposure to electromagnetic radiation emitted from electric power lines, home appliances and industrial devices.

- EMF measuring ranges: 20 micro Tesla (µT) / 200 µT / 2000 µT and 200 milli-Gauss (mG) / 2000 mG / 20000 mG
- EMF bandwidth: 30 Hz to 300 Hz
- Sampling time: Approx. 1 second

The heating mantle PCE-HM 2000 is used in applications where samples or liquids must be quickly heated in the laboratory. The flask may have a volume of up to 2 liters and it is placed in the crocheted net of the heating mantle. Here it is heated by the heating elements with a power of 450 W, and the temperature can be continuously adjusted up to 450 °C using the rotary switch on the heating mantle.

- Power 450 W
- Operating temperature 0 ... +450 °C
- Fast heat-up time
- For round flasks up to 2000 ml

A DIN flow cup meter is a viscometer to determine the toughness of liquids. It is commonly used in the industrial sector as well as in research laboratories. However, only low-viscosity liquids can be measured by means of this method as liquids cannot pass through the nozzles if their viscosity is too high.

- Capacity 100 ml
- With overflow gutter
- Meets international standards
- 2 editions available (flow or immersion cup)

 

The PCE-127 DIN flow cup viscometer or DIN immersion viscosity flow cup series uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a DIN flow cup is used to determine the kinematic viscosity of fluids. The structure of a DIN flow cup is standardized according to DIN 53211. Designed for use with Newtonian and near-Newtonian liquids, this viscosity cup series features:

- Orifice diameter (Ø) of 4 mm
- Viscosity range of 96.2 ... 680 mPa.s / cP
- Flow time of 25 ... 150 seconds

- Formaldehyde in mg / m³
- Measurement of TVOC
- Temperature measurement
- Alarm function
- Mass concentration

The PCE-125 series Ford Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a Ford cup is used to determine the kinematic viscosity of fluids. The structure of the Flow Cup Meter is standardized according to ASTM D1200 (Ford). This Flow Cup Meter series features:

- Orifice diameters (Ø inside) of 2.5 mm, 3.4 mm, 4.1 mm or 5.2 mm / 0.10 in,
  0.13 in, 0.16 in or 0.20 in
- Viscosity ranges of 25 ... 120, 49 ... 220, 70 ... 370 or 215 ... 1,413 cSt / mm²/s
- Flow times of 40 ... 100, 25 ... 105 or 20 ... 105 seconds (s)

 

The PCE-128 ISO / ASTM viscometer or ISO / ASTM Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, an ISO / ASTM cup is used to determine the kinematic viscosity of fluids. The structure of an ISO / ASTM Flow Cup Meter is standardized according to BS EN ISO 2431 / ASTM D5125. Designed for use with Newtonian and near-Newtonian liquids, this Flow Cup Meter series features:

- Orifice diameters (Ø) of 3 mm, 4 mm, 5 mm, 6 mm, or 8 mm / 0.12 in, 0.16 in,
  0.20 in, 0.24 in, or 0.31 in
- Viscosity ranges of 7 ... 42, 34 ... 135, 91 ... 326, 188 ... 684 or 600 ... 2,000 cSt /
  mm²/s
- Flow times of 25 ... 150 or 30 ... 100 seconds (s)

 

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

The PCE-125 series Ford Flow Cup Viscometer uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a Ford cup is used to determine the kinematic viscosity of fluids. The structure of the Flow Cup Viscometer is standardized according to ASTM D1200 (Ford). This Flow Cup Viscometer series features:
- Orifice diameters (Ø inside) of 2.5 mm, 3.4 mm, 4.1 mm, or 5.2 mm / 0.10 in, 0.13 in, 0.16 in, or 0.20 in
- Viscosity ranges of 25 ... 120, 49 ... 220, 70 ... 370 or 215 ... 1,413 cSt / mm²/s
- Flow times of 40 ... 100, 25 ... 105 or 20 ... 105 seconds (s)

The PCE-128 ISO / ASTM viscometer or ISO / ASTM Flow Cup Viscometer uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, an ISO / ASTM cup is used to determine the kinematic viscosity of fluids. The structure of an ISO / ASTM Flow Cup Viscometer is standardized according to BS EN ISO 2431 / ASTM D5125. Designed for use with Newtonian and near-Newtonian liquids, this Flow Cup Viscometer series features:
- Orifice diameters (Ø) of 3 mm, 4 mm, 5 mm, 6 mm, or 8 mm / 0.12 in, 0.16 in, 0.20 in, 0.24 in, or 0.31 in
- Viscosity ranges of 7 ... 42, 34 ... 135, 91 ... 326, 188 ... 684 or 600 ... 2,000 cSt / mm²/s
- Flow times of 25 ... 150 or 30 ... 100 seconds (s)

PCE-RCM 10 is a portable handheld air sampler or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also measures air temperature and relative humidity (RH).

- PM channels: PM 2.5, PM 10
- Particle sizes (in micrometers): 2.5 µm, 10 µm
- Temp. measuring range: -20 ... +70 °C / -4 ... +158 °F
- Humidity measuring range: 0 ... 100 % RH
- 2.4" full-color LCD with user-friendly graphics
- For indicative measurements

PCE-RCM 10 is a portable handheld Dust Monitor used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this Dust Monitor also measures air temperature and relative humidity (RH).

- PM channels: PM 2.5, PM 10
- Particle sizes (in micrometers): 2.5 µm, 10 µm
- Temp. measuring range: -20 ... +70 °C / -4 ... +158 °F
- Humidity measuring range: 0 ... 100 % RH
- 2.4" full-color LCD with user-friendly graphics
- For indicative measurements

- Drive of the stirring points: Motor
- Max. Stirring quantity: 10 l
- Adjustable speed: 200 ... 2200 rpm
- Accuracy Speed: ± 20 rpm
- Recommended length of the stirring rod: 25 ... 60 mm / 1 x 2.4 in

The heating mantle PCE-HM 5000 is used in applications where samples or liquids must be quickly heated in the laboratory. The flask may have a volume of up to 5 liters and it is placed in the crocheted net of the heating mantle. Here it is heated by the heating elements with a power of 800 W, and the temperature can be continuously adjusted up to 450 °C using the rotary switch on the heating mantle.

- Power 800 W
- Operating temperature 0 ... +450 °C
- Fast heat-up time
- For round flasks up to 5,000 ml

The inductive magnetic stirrer PCE-MSR-110, is a flat, space-saving laboratory magnetic stirrer. Due to the induction-based operation, a quiet operation and a flat design of the stirrer are made possible.

- Maximum stirring volume: 800 ml / 0.21 gallon based on water
- Flat construction
- Silent and wear-free drive
- Timer
- Agitator in stainless steel IP 65
- 1 stirring position Ø 94 mm / 3.7"
- Variably adjustable 15 - 1500 rpm

 

- Evaluation of adhesion
- For thin, thick or tough coatings
- Large, non-slip grip
- Various blades selectable

 

PCE-G28 is a portable, handheld magnetometer that detects electromagnetic fields (EMFs) and displays measurement results in milliGauss (mG) or microTesla (µT). This EMF radiation detector comes with an external 3-axis electromagnetic sensor (X, Y, Z direction).

- Measurement range: 0 ... 20000 mG / 0 ... 2000 µT
- Accuracy: ± 4% + 3 digits / ± 5% + 3 digits / ± 10% + 5 digits
- Resolution: 0.1 mG / 0.01 µT