Indicator

The pressure indicator is suitable for stationary and mobile pressure measurement. The pressure indicator is used in mechanical and plant engineering, laboratory technology and environmental technology. This pressure indicator is battery powered. The measuring range of the pressure indicator reaches up to 600 bar.

- Max. 600 bar / 8702 psi
- Rotating display
- For hygienic applications
- Media: water, oxygen, fuels and oils
- Print: absolute or relative (user selectable)
- Diaphragm: Ceramics
- Accuracy class: 0.2

The pressure indicator is suitable for flush mounting hygiene. Thus, the indicator can be installed both in the food industry as well as in medical technology. The pressure indicator on its rotatable display pressures up to 400 bar, relative or absolute. The operating fluid of the pressure indicator has a food safe FDA approval.

- Max. 400 bar / 5801 psi
- Rotating display
- For hygienic applications
- Media: water, paints and coatings, gases, viscous and paste media
- Pressure: relative
- Diaphragm: stainless steel flush
- Accuracy class: 0.2

The pressure indicator is suitable for flush sanitary installation. The pressure indicator may represent on its rotatable display pressures up to 40 bar, absolute or relative. The filling of the pressure indicator has a food safe FDA approval. The flush mounting of the pressure indicator can be sterilized.

- To 40 bar / 580 psi
- Relative and absolute pressure measurement
- Max-min function with reset
- 2-line backlit display

The pressure indicator is a precision instrument of the highest standards. The pressure indicator is specifically designed for process monitoring and calibration. This pressure indicator is distinguished by its modular concept. This means that the actual sensor and the display can be separated. The pressure transmitter can be selected on site for different measuring ranges and connected to the display without tools.

- Max. 400 bar / 5801 psi
- Media: water, gases
- Pressure type: Absolute / Relative
- Diaphragm: stainless steel
- Accuracy: 0.05 

The analogue indicator or display PCE-EP 29 is designed to measure simple three-phase-voltages. The analogue display PCE-EP 29 is designed for alternating currents and can measure up to 500 V directly without the need of a transformer (phase-to-phase). The analogue display is designed in CAT III and can be applied to many monitoring tasks of voltages in system control.

- Analogue voltmeter with change over
- 96 x 96 mm
- Panel installation 

The digital temperature indicator is used for processing signals coming from temperature sensors. Depending on your specific needs, the temperature indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the temperature indicator is freely scalable, which increases its application possibilities.

- IP65 protected front
- For thermocouples and resistance thermometers
- Configuration via software
- 5-digit LED display

The frequency indicator is used for the signal processing of 4 .. 20 mA. The frequency indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

The panel indicator is used for the signal processing of 4 .. 20 mA. The panel indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

The power indicator is used for the signal processing of 4 .. 20 mA. The power indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

The pressure indicator is used for the signal processing of 4 .. 20 mA. The pressure indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm