Power Indicator

The power indicator PCE-N27P measures current up to 63 A directly. This makes it possible to connect the power display directly to the main distribution. The power indicator PCE-N27P measures all relevant network parameters such as current, voltage, power and frequency. The power indicator PCE-N27P is ideally suited for measurement purposes in order to comply with the ISO 50001 energy management standard.

Measures up to 63 A directly

Measuring about 1A / 5A transducer possible

Measurement of U, I, f, P

DIN rail

The Power Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the power indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the power indicator is freely scalable, which increases its application possibilities.

The PCE-N24S power indicator is used for the signal processing of 4 .. 20 mA. The PCE-N24S power indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

PCE-N20U is a power indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

The power indicator PCE-N30U can process several different input signals, such as 0...410/4010 Ohm, -10...+63 mV DC, -13...+13 V DC, -24...+24 mA DC or signals from thermocouples and resistance thermometers. This makes the power indicator applicable in a wide range of applications. The measured values are shown on the large LED display of the PCE-N30U.

- 21-point scaling
- IP 65 protection on the front
- Three-colored display
- Two alarm outputs

The PCE-ND20 built-in power indicator measures 3-phase all network parameters. Power, voltage, and power measurements are no problem for the PCE-ND20 built-in power indicator. The current measurement can be done with the built-in power measuring device 3-phase and directly. However, it is also possible to measure high currents by means of transducers using the built-in power indicator PCE-ND20.

- Illuminated 3.5" LCD display
- Easy installation
- RS485 Modbus interface 

 

The power indicator PCE-NR30 is able to measure currents directly up to 63 A AC. The power indicator measures network parameters of symmetrically and asymmetrically loaded single-phase 2-wire systems and three-phase 3 or 4-wire systems.

- DIN rail power meter
- Measurement up to 63 A.
- For single-phase and three-phase systems
- Ethernet
- Data logger
- Profinet

The power indicator PCE-NR30 is able to measure currents directly up to 63 A AC. The power indicator measures network parameters of symmetrically and asymmetrically loaded single-phase 2-wire systems and three-phase 3 or 4-wire systems.

- DIN rail power meter
- Measurement up to 63 A.
- For single-phase and three-phase systems
- Ethernet
- Data logger

The power indicator PCE-NR30 is able to measure currents directly up to 63 A AC. The power indicator measures network parameters of symmetrically and asymmetrically loaded single-phase 2-wire systems and three-phase 3 or 4-wire systems.

- DIN rail power meter
- Measurement up to 63 A.
- For single-phase and three-phase systems
- Ethernet
- Data logger
- MQTT protocol for Industry 4.0 applications