Control Systems

You will find a wide range of control systems to be used for many different applications from simple displays with different sizes up to complete regulators. Nowadays, control systems are essential instruments in modern production processes. The compact displays of these control systems enable quick and easy view of diverse physical magnitudes, such as temperature, pressure, revolutions and standard process signals which can be found in any automated process. Besides, modern regulators can solve quickly and effectively different control works.
Order no.: PCE-N25S
The digital universal indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the digital universal indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the digital universal indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Frequency Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the frequency indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the frequency indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Panel Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the panel indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the panel indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Power Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the power indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the power indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Pressure Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the pressure indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the pressure indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Process Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the process indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the process indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The temperature indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the digital universal indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the digital universal indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25T

The digital temperature indicator PCE-N25T is used for processing signals coming from temperature sensors. Depending on your specific needs, the digital indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the digital indicator is freely scalable, which increases its application possibilities.


- IP65 protected front
- For thermocouples and resistance thermometers
- Configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N25S
The Voltage Indicator PCE-N25S is used for processing standardised signals. Depending on your specific needs, the voltage indicator can be ordered with different inputs, such as 0...20 mA, 4...20 mA, 0...60 mV, 0...10 V, ±60 mV or ±10 V. The input signal of the voltage indicator is freely scalable, which increases its application possibilities.

 

- IP65 protected at the front
- 6 different standardised signal inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PA39
The analogue indicator PCE-PA39 is designed to monitor AC power. This analogue indicator can be installed onto switch panels. The analogue indicator PCE-PA39 is a moving-coil ammeter. Active power as well as apparent power can be measured by means of this analogue indicator PCE-PA39.

- Moving-coil meter to measure electric power
- 96 x 96 mm
- Panel installation
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-C91P

The temperature controller PCE-C 91 is a very compact PID controller measuring 48 x 48 mm / 1.9 x 1.9" (1/16 DIN). To make safe and fast control possible, the temperature controller is equipped with a fuzzy controller. This changes the PID parameters in the temperature controller so that setpoints can be reached quickly but with little overshoot. Thanks to a measuring rate of 5 Hz, this temperature controller can also be used in fast processes.

 

- Input: 4 ... 20 mA
- Output: relay or analog (selectable)
- Sensor supply: 20 V
- Measuring time: 200 ms

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20I

The PCE-N20I digital universal indicator is used for processing 4...20 mA and 0...20 mA signals. Many measuring transducers and sensors use this type of output, which makes the PCE-N20I suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the PCE-N20I.


- Input (selectable): 0...20 mA, 4...20 mA, ± 20 mA
- Accuracy: ± (0.2 % FS + 1 dgt.)
- Two open collector outputs
- 24 V power supply sytem for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20U

PCE-N20U is a digital universal indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.


- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20I

The PCE-N20I frequency indicator is used for processing 4...20 mA and 0...20 mA signals. Many measuring transducers and sensors use this type of output, which makes the PCE-N20I suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the PCE-N20I.


- Input (selectable): 0...20 mA, 4...20 mA, ± 20 mA
- Accuracy: ± (0.2 % FS + 1 dgt.)
- Two open collector outputs
- 24 V power supply sytem for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20U

PCE-N20U is a frequency indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.


- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20I

The PCE-N20I panel indicator is used for processing 4...20 mA and 0...20 mA signals. Many measuring transducers and sensors use this type of output, which makes the PCE-N20I suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the PCE-N20I.


- Input (selectable): 0...20 mA, 4...20 mA, ± 20 mA
- Accuracy: ± (0.2 % FS + 1 dgt.)
- Two open collector outputs
- 24 V power supply sytem for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20U

PCE-N20U is a panel indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.


- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20U

PCE-N20U is a power indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.


- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20I

The PCE-N20I pressure indicator is used for processing 4...20 mA and 0...20 mA signals. Many measuring transducers and sensors use this type of output, which makes the PCE-N20I suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the PCE-N20I.


- Input (selectable): 0...20 mA, 4...20 mA, ± 20 mA
- Accuracy: ± (0.2 % FS + 1 dgt.)
- Two open collector outputs
- 24 V power supply sytem for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N20U

PCE-N20U is a pressure indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.


- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

Manufacturer: PCE Instruments
Test Instruments manufacturer