Control Systems

You will find a wide range of control systems to be used for many different applications from simple displays with different sizes up to complete regulators. Nowadays, control systems are essential instruments in modern production processes. The compact displays of these control systems enable quick and easy view of diverse physical magnitudes, such as temperature, pressure, revolutions and standard process signals which can be found in any automated process. Besides, modern regulators can solve quickly and effectively different control works.
Order no.: PCE-DPD-F2
The built-in display is used to indicate the force and weight, which is determined by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the DMS display makes it possible to display the correct weight in mV / V based on the set sensitivity. The DMS display shows the measured values ​​on a 6-digit LED display. 

- Power supply: 11 ... 60V DC / 24/48V AC
- Input signal: mV / V for force and weighing sensors
- Display: 6 digits, red
- Digit height : 14 mm
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-N50B
The panel indicator has a RS485 Modbus interface. This digital Modbus panel indicator can display the measured data of up to 10 slave devices or registers. 

- Interface: RS 485 Modbus RTU Master
- Number of slave devices / registers: 10
- Baud rate individually adjustable
- Further power supply area
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DPD-F1
The built-in display is used to indicate the force and weight, which is detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the DMS display makes it possible to display the correct weight in mV / V based on the set sensitivity. The DMS display shows the measured values ​​on a 6-digit LED display. 

- Power supply: 85 ... 265V AC / DC
- Input signal: mV / V for force and weighing sensors
- Display: 6 digits, red
- Digit height : 14 mm
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LPS 4305
Thanks to the many different connections, different consumers can be connected to the laboratory power supply and operated at the same time. In addition, with the laboratory power supply it is possible to switch channel 1 and channel 2 internally in series and parallel in addition to the normal output mode. - 4 individually adjustable channels - with USB fixed voltage regulator - Switchable to parallel and series connection
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DMM 11

The pressure indicator PCE-DMM 11 is distinguished by the long battery life of 1800h. The rotatable housing and display completes the functionality of the manometer. Thus, the pressure indicator PCE-DMM 11 is ideal for mobile applications, such as test beds.


- Up to 600 bar / 8702 psi
- Relative pressure
- Revolving 4.5 digit display
- Max-Min function
- Different units 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DMM 11

The pressure sensor PCE-DMM 11 is distinguished by the long battery life of 1800h. The rotatable housing and display completes the functionality of the manometer. Thus, the pressure sensor PCE-DMM 11 is ideal for mobile applications, such as test beds.


- Up to 600 bar / 8702 psi
- Relative pressure
- Revolving 4.5 digit display
- Max-Min function
- Different units 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IR 50

With the temperature sensor PCE-IR 50, surface temperatures can measured quickly and easily. The measuring range of the temperature sensor is 0 ...500 °C / 32 ... 932°F. The measured temperature is output as a 4 ... 20-mA standard signal which means that the temperature sensor can be easily integrated into different monitoring systems, including those in different production processes or food storage as well as the monitoring of electronic systems.


- Measurement range: 0 ... 500°C / 32 ... 932°F
- Accuracy: ± 1.5°C or ± 1%
- Optical resolution: 15:1
- Output signal: 4 ... 20-mA standard signal
- For fixed installation (mounting bracket incl.)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IR 50

With the Thermo Transducer PCE-IR 50, surface temperatures can measured quickly and easily. The measuring range of the thermo transducer is 0 ... 500 °C / 32 ... 932 °F. The measured temperature is output as a 4 ... 20-mA standard signal which means that the thermo transducer can be easily integrated into different monitoring systems, including those in different production processes or food storage as well as the monitoring of electronic systems.


- Measurement range: 0 ... 500 °C / 32 ... 932 °F
- Accuracy: ± 1.5 °C or ± 1 %
- Optical resolution: 15:1
- Output signal: 4 ... 20-mA standard signal
- For fixed installation (mounting bracket incl.)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HPS 4500
The Laboratory Switching Power Supply has a voltage output of up to 500 V. This means that even consumers who need a higher voltage can be checked with the laboratory switching power supply. This enables transformers to be checked for their winding ratio using the laboratory switched-mode power supply. In order to minimize the risk of electric shock, the connection side of the laboratory switching power supply is equipped with 4 mm safety sockets. - 4 individually adjustable channels - Output voltage up to 500 V. - Handle for mobile transportation - self-regulating active cooling - 4 mm safety banana sockets - Protective conductor connection on the connection side
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-ND30

The power indicator PCE-ND30 can be used to measure 54 parameters in a UI network. In addition to the performance measurement of the power indicator PCE-ND30, it can detect voltage, current, and harmonics up to the 51st order. The power display can be used as 1 or 3 phase. It does not matter if the connected load is balanced or unbalanced.


- Measurement of all parameters of a U/I network
- Harmonics measurement up to 51st order
- 2 x PT100 Input Optional
- RS485 Modbus 

 

Note: This item must be configured before ordering!

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VS10

PCE-VS10 is a vibration meter, analyzer or sensor condition monitoring switch used to measure RMS and peak value of vibration velocity or acceleration piezoelectrically. This IP67-rated vibration monitoring switch features a red and green visual warning or alarm with programmable high pass and low pass filters.


- Frequency range (max.): 0.1 Hz ...10 kHz
- Measuring range: Acceleration = 0.1 ... 1000 m/s², Speed = Frequency-dependent
- Connections: Screw terminals for power supply (5 ... 30V DC) and Micro USB (internal)
- Mounting: M8 stud bolt

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RE100P
The universal input controller is used for temperature and process control. The various inputs and outputs, which are installed as standard on the PID controller, make it possible for the PID controller to be used universally.

Measurement functions:
- Process flow
- mV
- Process voltage
- Resistance
- Autotune PID
- Memory for several PID parameters
- RS485 Modbus interface
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RE110P
The 2 channel universal input controller is used for temperature and process control. The various inputs and outputs, which are installed as standard on the PID controller, make it possible for the PID controller to be used universally.

Measurement functions:
- Process flow
- mV
- Process voltage
- Resistance
- Autotune PID
- Memory for several PID parameters
- RS485 Modbus interface
- 2 measuring inputs
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SM61
The remote maintenance module PCE-SM61 allows you to quickly and easily query your process data via the Internet. Any device with RS485 interface can be connected to the remote maintenance module. The data is retrieved via a web browser and can be carried out simultaneously by the PC, smartphone, tablet, etc., and by several users. In addition to the data query, the remote maintenance module can trigger alarms. The configuration can be done via USB or Ethernet interface.

 

- up to 100 devices with 25 registers can be connected
- Configuration via webbrowser
- Interface: RS485, Ethernet
- Memory: 1 GB Flash
- additional inputs / outputs: digital input or relay output (selectable)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-G 2
The Temperature Indicator PCE-G 2 is used to measure the environmental parameters of temperature and humidity. The temperature indicator is used in warehouses, open-plan offices, schools, etc.

- Measuring range temperature: -40 ... 85 °C
- Measuring range humidity: 0 ... 99 % r.H.
- 55 mm character height
- Up to 30 m reading distance
- External sensor (wired)
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-NA5

The digital temperature indicator PCE-NA5 is equipped with a 55-digit bar graph display, which is freely programmable. In addition, the digital indicator also comes with a conventional display, which shows the active measuring value as a figure. The digital universal indicator PCE-NA5 is able to process a large variety of signals.


- 55-digit bar graph display
- 4-digit, 7-segment display
- Analogue output
- Four alarm relays

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DDMU 10
The pressure transmitter PCE-DDMU 10 can be used for gases and air. The pressure transmitter can be used for relative and differential pressure.

- Max. ± 0.5% accuracy
- Optional display
- Switching outputs
- Radiated output signal
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DMU 40

The pressure transmitter PCE-DMU 40 can be used for relative and absolute pressure measurements. The pressure transmitter can be used for gases, water as well as fuels and oils.

 

- max. 600 Bar
- Media: gases, water as well as fuels and oil
- Output: 4 ... 20 mA / 0 ... 10 V (selectable)
- Pressure type: Absolute or Relative (selectable)
- Membrane: stainless steel
- Accuracy: 0.1 % / 0.25 % FSO

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 425

The Modbus display was developed for Modbus RTU slave devices. Up to 10 devices can be connected to the Modbus display. The display saves the measurement data on an internal memory. 

- Ethernet with PoE
- RS485 Modbus 
- Modbus RTU / TCP
- Email alarm and acoustic alarm
- 8 GB storage
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DMM 20

The Pressure Indicator PCE-DMM 20 has a two-line display. The pressure indicator can represent pressures up to 600 bar, relative or absolute. The parts of the gauge PCE-DMM 20 that come in contact with liquids are made of stainless steel.


- Max. 600 bar / 8702 psi
- Rotating display
- Battery operation
- Media: gas, water, fuels and oils
- Print: absolute or relative (user selectable)
- Diaphragm: stainless steel
- Accuracy class: 0.1

 

Manufacturer: PCE Instruments
Test Instruments manufacturer