Industrial Measurement Products and Solutions

Laboratory Technology

Order no.: BSB OxiDirect

The BOD meter OxiDirect by Tintometer is a device that is designed to determine the biochemical oxygen demand, i.e. B.O.D. By means of the BOD meter the samples can be taken without further ado, and the BOD values are displayed in real-time speed, precisely in mg/l. Each BOD meter features, depending on the edition, six or twelve sample containers.

 

- Immediate display of BOD level in mg/l
- RS232 interface
- Total measurement range of 0 ... 4,000 mg/l

Manufacturer: Tintometer GmbH
Test Instruments manufacturer
Order no.: PCE-AS1

PCE-AS1 is an air sampling meter used to assess microbiological pollution and monitor hygiene. Designed for use in hospitals, clean rooms, food, beverage, cosmetics, and pharmaceutical production facilities. The PCE-AS1 air sampler meets the latest requirements for devices used for airborne microbial analysis.


- Accommodates manual adjustment of volumes from 10 to 6000 liters
- Offers data storage for up to 99 parameters / 2000 measurement records
- Aids in compliance with HACCP, FDA FMSA and ISO 14698-1
- Runs off a rechargeable battery or AC power
- Supports standard Petri dishes 90 mm

 

Manufacturer: PCE Instruments
Order no.: PCE-MSR 100

PCE-MSR 100 is a magnetic stirrer or magnetic stir plate commonly used in laboratories to ensure liquid samples are homogeneous in consistency and temperature. Proper mixing also boosts sensor response time, allowing measuring instruments to achieve stable readings more quickly.


- Maximum stirring volume: 2 Liters (L) ≈ 0.52 gallon
- Adjustable stirring speeds: 0 ... 1250 rpm
- Includes one magnetic stirrer bar 

 

Manufacturer: PCE Instruments
Order no.: PCE-127

A DIN flow cup meter is a viscometer to determine the toughness of liquids. It is commonly used in the industrial sector as well as in research laboratories. However, only low-viscosity liquids can be measured by means of this method as liquids cannot pass through the nozzles if their viscosity is too high.


- Capacity 100 ml
- With overflow gutter
- Meets international standards
- 2 editions available (flow or immersion cup)

 

Manufacturer: PCE Instruments
Order no.: PCE-125

The PCE-125 series Ford Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a Ford cup is used to determine the kinematic viscosity of fluids. The structure of the Flow Cup Meter is standardized according to ASTM D1200 (Ford). This Flow Cup Meter series features:


- Orifice diameters (Ø inside) of 2.5 mm, 3.4 mm, 4.1 mm or 5.2 mm / 0.10 in,
  0.13 in, 0.16 in or 0.20 in

- Viscosity ranges of 25 ... 120, 49 ... 220, 70 ... 370 or 215 ... 1,413 cSt / mm²/s
- Flow times of 40 ... 100, 25 ... 105 or 20 ... 105 seconds (s)

 

Manufacturer: PCE Instruments
Order no.: PCE-128

The PCE-128 ISO / ASTM viscometer or ISO / ASTM Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, an ISO / ASTM cup is used to determine the kinematic viscosity of fluids. The structure of an ISO / ASTM Flow Cup Meter is standardized according to BS EN ISO 2431 / ASTM D5125. Designed for use with Newtonian and near-Newtonian liquids, this Flow Cup Meter series features:


- Orifice diameters (Ø) of 3 mm, 4 mm, 5 mm, 6 mm, or 8 mm / 0.12 in, 0.16 in,
  0.20 in, 0.24 in, or 0.31 in

- Viscosity ranges of 7 ... 42, 34 ... 135, 91 ... 326, 188 ... 684 or 600 ... 2,000 cSt /
  mm²/s
- Flow times of 25 ... 150 or 30 ... 100 seconds (s)

 

Manufacturer: PCE Instruments
Order no.: PCE-HM 1000

The heating mantle PCE-HM 1000 is an auxiliary device, which is used in laboratories. The heating mantle helps to heat or control the temperature of different samples or chemicals in the laboratory. The piston can be hooked into the crocheted net inside the heating mantle and subsequently heated.


- Power 350 W
- Operating temperature 0 ... +450 °C
- Low heat-up time
- For round flasks up to 1,000 ml

 

Manufacturer: PCE Instruments
Order no.: PCE-RCM 10

PCE-RCM 10 is a portable handheld air sampler or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also measures air temperature and relative humidity (RH).


- PM channels: PM 2.5, PM 10
- Particle sizes (in micrometers): 2.5 µm, 10 µm
- Temp. measuring range: -20 ... +70 °C / -4 ... +158 °F
- Humidity measuring range: 0 ... 100 % RH
- 2.4" full-color LCD with user-friendly graphics

Manufacturer: PCE Instruments
Order no.: PCE-MSR 110
The inductive magnetic stirrer PCE-MSR-110, is a flat, space-saving laboratory magnetic stirrer. Due to the induction-based operation, a quiet operation and a flat design of the stirrer are made possible.

- Maximum stirring volume: 800 ml / 0.21 gallon based on water
- Flat construction
- Silent and wear-free drive
- Timer
- Agitator in stainless steel IP 65
- 1 stirring position Ø 94 mm / 3.7"
- Variably adjustable 15 - 1500 rpm
Manufacturer: PCE Instruments
Order no.: PCE-MSR 150
The magnetic stirrer PCE-MSR 150 is suitable for volumes up to 10 liters. The magnetic stirrer has an adjustable speed range of 200 ... 2200 rpm. The speed can be changed step by step in 10 rpm. You can buy the magnetic stirrer PCE-MSR 150 here in our online shop.

- Drive of the stirring points: Motor
- Max. Stirring quantity: 10 l
- Adjustable speed: 200 ... 2200 rpm
- Accuracy Speed: ± 20 rpm
- Recommended length of the stirring rod: 25 ... 60 mm / 1 x 2.4 in
Manufacturer: PCE Instruments
Order no.: PCE-HM 5000

The heating mantle PCE-HM 5000 is used in applications where samples or liquids must be heated in the laboratory quickly. The piston may have a volume of up to 5 liters and is set for heating in the crocheted net heating mantle. Here it is heated by the heating elements with a power of 800 W, and the temperature can be adjusted using the rotary switch on the heating mantle continuously up to 450 °C.


- Power 800 W
- Operating temperature 0 ... +450 °C
- Low heat-up time
- For round flasks up to 5,000 ml

 

Manufacturer: PCE Instruments
Order no.: PCE-HMA

A heating mantle is used in the laboratory for the heating of round bottom flasks and their contents. The round-bottomed flasks are filled and heated. The PCE-HMA series is available in different sizes. The heating mantle is controlled by a slider. All models of the series are equipped with RCD protection. 

- Capacity of round-bottomed flask: 25 - 20000 ml 
- Diameter of round-bottomed flask: 41 - 345 mm / 1.6 - 13.6"
- Operating temperature: 0 ... +450 °C / +32 ... 842 °F
- Short heat-up time
- For round bottom flasks with a capacity of up to 20 l
- Control via a slider
- With external RCD protection

Different variants selectable!

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MSR 300

Magnetic PCE-MSR 300 with a large display and ability to set temperature, stirring speed and time. The adjusted data can be read directly on the display of the magnetic stirrer.


- Stirring capacity: 2 liters
- Stirring speed: 0 ... 1250 rpm
- Temperature range: 20 ... 300°C / 68 ... 572°F
- Timer: 0 ... 999 min

 

Manufacturer: PCE Instruments
Order no.: PCE-RCM 12
The air sampler PCE-RCM 12 is used for orientation testing of environmental parameters. The air sampler PCE-RCM 12 enables the measurement of CO2, fine dust, temperature and relative humidity. The bright display of the air sampler provides information about these parameters. 


- Fine dust, CO2, formaldehyde, humidity, temperature
- Particle size channels: PM 2.5 / PM 10
- Temperature measuring range: -20 ... +70 °C / -4 ... +158°F
- Humidity measuring range: 0 ... 100 % r.H.
- Formaldehyde measuring range: 0.00 ... 5.00 mg/m³
- CO2 measuring range: 0 ... 9999 ppm
- For orientation measurements
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MSR 350
The magnetic stirrer with heater PCE-MSR 350 can be used for aqueous solutions up to 10 liters. The magnetic stirrer PCE-MSR 350 also has a heater that can heat the medium from room temperature up to 230 °C / 446 °F. 

- Stirring drive: Motorised
- Max. Stirring volume: 10 l
- Adjustable speed: 200 ... 2200 rpm
- Accuracy of speed: ± 20 rpm
- Heating up to 230 °C / 446 °F
- Pulse function
Manufacturer: PCE Instruments
Order no.: PCE-MPC 10

PCE-MPC 10 is a portable handheld air sampler or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also measures air temperature and relative humidity (RH).


- PM channels: PM 2.5, PM 10
- Particle sizes (in micrometers): 2.5 µm, 10 µm
- Temp. measuring range: 0 ... +50 °C / +32 ... +122 °F
- Humidity measuring range: 0 ... 100 % RH
- 2" full-color LCD with user-friendly graphics
- Integrated data logger with adjustable sampling time
- Internal memory stores up to 5000 date-and-time-stamped data sets

Manufacturer: PCE Instruments
Order no.: PCE-MSR 400

PCE-MSR 400 is a multi-position magnetic stirrer with four stirring points for stirring up to four beakers simultaneously. This multi-beaker laboratory stir plate uses the induction method for quiet stirring. The flat stainless steel design is both low profile and easy to clean.


- Adjustable speed: 15 ... 1200 rpm
- Timer
- Stir plate made of stainless steel
- IP65 ingress protection rating
- 4 stirring points

Manufacturer: PCE Instruments
Order no.: PCE-TUM 20

PCE-TUM 20 is a portable handheld turbidity meter or turbidimeter for water quality analysis. This turbidity measuring device is equipped with a large LCD screen and user-friendly keyboard. The turbidity meter features two automatically switching measuring ranges between 0 ... 50 NTU and 50 ... 1000 NTU for increased accuracy.


- 0 ... 1000 NTU turbidity measuring range
- Infrared LED light source
- Calibration references included

Manufacturer: PCE Instruments
Order no.: PCE-MSR 450
The magnetic stirrer PCE-MSR 450 is a stirring instrument for up to 20 liters. The speed of the magnetic stirrer can be adjusted. It is possible to set speeds between 200 and 2200 revolutions per minute. 

- Motor: brushless DC motor (BLDC)
- Number of stirring points: 1
- Maximum stirring volume: 20 l
- Speed range: 200 ... 2200 rpm (adjustable)
- Accuracy: +/- 1 rpm
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-CFE 200

PCE-CFE 200 is a compact, programmable micro-centrifuge for laboratory benchtop use. This vital piece of lab equipment spins liquid samples at high speeds to separate particles or macromolecules from suspensions and solutions. Equipped with a variety of important safety features, this space-saving centrifuge:


- Offers a rotational speed of 500 ... 15,000 rpm
- Contains a fixed angle rotor for 12 x 2 ml microtubes
- Includes an adapter for 0.2, 0.4 and 0.5 ml PCR tubes

 

Manufacturer: PCE Instruments