Control Systems

The voltage indicator is used to display AC parameters. The voltage indicator can measure and display AC current, AC voltage or frequencies. The possibility of freely scaling the input signal allows a very versatile use of this voltage indicator.

• Power supply:   230V, 110V, 24V, 20 … 40V AC/DC,   85 … 253 V AC/DC (selectable)
• Input signal:   1 … 100V, 2.5 … 250V, 4 … 400V,   20 … 500 Hz, 1 A, 5 A (selectable)
• Display: 4 digits, red
• Digit height: 20 mm / 0.78"

• Frequency Indicator mode
• DC voltage: 0 ... 999.9 V
• AC voltage: 0 ... 750 V
• direct current: 0 ... 10 A
• alternating current 0 ... 10 A
• frequency: 40 Hz ... 1 kHz
• resistance: 0 ... 99.99 MΩ
• capacitance: 0 ... 99.99 mF
• temperature: -20 ... +1000 °C
• graphical display of the measured value

• 2-channel Frequency Indicator
• bandwidth: 10 MHz, sampling rate: 50 MS/s
• voltage: 0 ... 1000 V DC, 0 ... 750 V AC
• current: 0 ... 9.999 A AC/DC
• resistance, capacitance, temperature
• non-contact voltage detection
• signal generator: 1 Hz ... 2 MHz

• Illuminance: 0 ... 65535 lx
• Resolution: 1 lx - Accuracy: ±7 % FS @25°C / 77°F
• Protection class: IP65
• Output: RS-485 Modbus RTU*

The panel indicator PCE-N24T is used for processing signals coming from temperature sensors. Depending on your specific needs, the digital indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the digital indicator is freely scalable, which increases its application possibilities.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: PT100, Thermoelement Type J / K (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

The panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: PT100, Thermoelement Type J / K (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

The digital temperature indicator PCE-N24T is used for processing signals coming from temperature sensors. Depending on your specific needs, the digital indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the digital indicator is freely scalable, which increases its application possibilities.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: PT100, Thermoelement Type J / K (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

The frequency indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the frequency indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the frequency indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

PCE-N20U is a frequency indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The panel indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the panel indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the panel indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a panel indicator used for signal processing. Designed for quick and easy system integration, the digital panel indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The panel indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The panel meter is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the panel meter suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the panel meter.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a panel meter used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The panel meter also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The PCE-N20U is a power indicator used for signal processing. Designed for quick and easy system integration, the digital power indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The power indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The pressure indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the pressure indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the pressure indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a pressure indicator used for signal processing. Designed for quick and easy system integration, the digital pressure indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The pressure indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The process indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the process indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the process indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a process indicator used for signal processing. Designed for quick and easy system integration, the digital process indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The process indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The digital temperature indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the digital temperature suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the digital temperature.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a digital temperature indicator used for signal processing. Designed for quick and easy system integration, the digital temperature indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The temperature indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The voltage indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the voltage indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the voltage indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a voltage indicator used for signal processing. Designed for quick and easy system integration, the digital voltage indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The voltage indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The digital universal indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the digital universal indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the digital universal indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The 2-point process controller / temperature controller is a compact temperature controller for use in a wide range of tasks. This 2-point temperature controller PCE-RE22P processes the process signals 0 … 20mA, 4 … 20 mA, 0 … 5 V and 0 … 10 V as input signals. Different operating modes can be selected to optimally regulate the controlled variable to the reference variable.

• Power supply: 230 V AC, 110 V AC, 24 V AC (selectable)
• Process signals: 0/4 … 20 mA, 0 … 5/10 V
• Output: Relay / SSR (selectable)
• Manual control mode

The 2-point process controller / temperature controller is a compact PID controller for a wide range of tasks. As an input signal, this 2-point temperature controller PCE-RE22 processes resistance sensors and thermocouples. Different operating modes can be selected for optimum control of the control variable. Starting with a simple on / off control with adjustable hysteresis up to the PID control, the 2-point temperature controller offers a wide range of possibilities.

• Signal input: temperature signals (PT100, PT1000, J, T, K, S, R, B, E, N, L) 
• Possible control characteristics: P, PD, PI, PID, On / Off control
• Front is protected to IP 65
• 4 LEDs for status display

The PCE-P20Z transmitter is used to convert a measured current into a standard signal. This makes it possible to determine the most diverse currents with the transmitter.

• Input: Alternating current
• Various supply voltages
• For direct or indirect current measurement
• Current transformer can be connected
• With voltage output or current output

Note: This item must be configured before ordering!

The digital panel indicator is used for processing signals from Pt100 temperature sensors or thermocouples (type J, K). The measurement results are shown on the large 5-digit LED-display of the panel indicator. Depending on the actual values, the temperature can be shown in three different colors, which makes it easier to evaluate them.

• Input: Pt100, thermocouple type J or type K
• Accuracy: ± (0.2 % FS + 1 dgt.)
• two open collector outputs
• 24 V power supply sytem for sensors and transducers
• 5-digit, three-coloured LED display