The PCE-160 CT cable fault meter is a line locator for hard-to-reach cables and is used, for example, in the automotive sector. In addition to the line location, there is also the continuity test with the cable fault meter.
- Sensitivity adjustment
- Headphone jack
- Different beeps
- Cable tracking in walls and cable channels
- For mobile use
PCE-180 CBN is a handheld, portable, battery-powered wire tracer or cable locator that consists of an amplifier probe and acoustic signal or tone generator. This locating device is designed to detect wires or cables hidden behind walls or insulation.
- Uses an acoustic signal to detect wires and cables, including network and coaxial cables - Features a 3-position toggle switch (and 3-color LED) for line polarity, continuity and voltage testing - Comes with red and black test leads with alligator clips
The cable fault meter PCE-186 CB consists of a transmitter and a receiver. The transmitter of the cable fault meter has many functions. For example, the cable fault meter can be used to find wires in walls or break cables.
- Voltage measurement AC / DC
- For detection of line interruptions
- Cable tracking in walls and cable duct
- Different beeps
- Resistance measurement
The PCE-CL 20 is a cable fault meter or locator used to detect live and voltage-free electrical wires. This cable fault meter also can be used to locate metallic and non-metallic gas or water pipes, identify short circuits, and follow lines inside walls or under flooring.
- Output signal: 125 kHz - Compatible with one- or two-pole circuits - Automatic, manual and UAC measuring modes
The cable fault meter PCE-CLT 10 is a multifunctional device which enables high accuracy and fast measurement results. If used appropriately, the cable fault meter can be used to measure cables that have already been installed and are still to be installed.
- Measuring range cable length: 5 ... 3000 m / 16.4 ... 9842.5 ft
- Measurement Units: m, ft
- Resolution: 0.1 m / 0.3 ft
- Measuring principle: time domain reflectometer
- 20 pre-set cable types
The cable fault meter represents a powerful and versatile measuring instrument specifically designed for the precise measurement of electrical cables and conductors. With an impressive measurement range from 0.1 meters to an astonishing 30 kilometers, this device can measure and display cable lengths. Since the cable fault meter determines length based on conductor resistance, it can also measure resistance from 0.1 mΩ to 1999.9 Ω.
- Cable Length: 0.1 m ... 30 km
- Standard Cable Types: Selectable from 0.15 ... 240 mm²
The cable fault meter is a versatile measuring instrument. In addition to the standard voltage and current measurements, the cable fault meter also has a network analysis. With this network analysis, the cable fault meter can be used to check, for example, LAN connections for their correct wiring and function.
Measurement function:
- AC voltage
- DC voltage
- AC
- DC
- Resistance
- Diode measurement
- Continuity test
The PCE-160 CT cable locator is a line locator for hard-to-reach cables and is used, for example, in the automotive sector. In addition to the line location, there is also the continuity test with the cable locator.
- Sensitivity adjustment
- Headphone jack
- Different beeps
- Cable tracking in walls and cable channels
- For mobile use
The cable locator is a universal measuring device. With this cable locator, for example, RJ11 ISDN telephone lines can be checked for their function. For this purpose it is sufficient to connect the RJ 11 plug of the cable locator with the telephone socket.
Test functions
- Network cable testing
- Coaxial cable test
- Network cable finder
- Continuity test
- Telephone line test
PCE-180 CBN is a handheld, portable, battery-powered wire tracer or cable locator that consists of an amplifier probe and acoustic signal or tone generator. This locating device is designed to detect wires or cables hidden behind walls or insulation.
- Uses an acoustic signal to detect wires and cables, including network and coaxial cables - Features a 3-position toggle switch (and 3-color LED) for line polarity, continuity and voltage testing - Comes with red and black test leads with alligator clips
The cable locator PCE-186 CB consists of a transmitter and a receiver. The transmitter of the cable locator has many functions. For example, the cable locator can be used to find wires in walls or break cables.
- Voltage measurement AC / DC
- For detection of line interruptions
- Cable tracking in walls and cable duct
- Different beeps
- Resistance measurement
PCE-191 CB is a handheld, portable wire tracer, cable detector or cable fault meter used for locating wires and cables hidden behind walls and insulation.
- Power range: 220 to 240 V AC - Frequency range: 50 / 60 Hz - Acoustic alarm
PCE-CL 10 is a cable locator that uses the conductive method to detect metal pipes or pipe tracer wires. With PCE-CL 10, you also can locate power cables, lines, circuits, short circuits and ground points, as well as test protective tubing and coaxial cables. To perform these functions, it is not necessary to disconnect the power. Location can be identified in floors, ceilings, walls and the ground, even behind concrete and brick.
- Operating temperature / humidity: 0 ... +40 ºC or +32 ... +104 ºF / max. 80% rh - Storing temperature / humidity: -20 ... +60 ºC or -4 ... +140 ºF/ max. 80% rh - Max. Voltage: 400 VAC (0 - 60 Hz) / 400 V DC
The PCE-CL 20 is a cable locator used to detect live and voltage-free electrical wires. This cable detector also can be used to locate metallic and non-metallic gas or water pipes, identify short circuits, and follow lines inside walls or under flooring.
- Output signal: 125 kHz - Compatible with one- or two-pole circuits - Automatic, manual and UAC measuring modes
The Cable Locator PCE-CLT 10 is a multifunctional device which enables high accuracy and fast measurement results. If used appropriately, the Cable Locator can be used to measure cables that are installed and are still to be installed.
- Measuring range cable length: 5 ... 3000 m / 16.4 ... 9842.5 ft
- Measurement Units: m, ft
- Resolution: 0.1 m / 0.3 ft
- Measuring principle: time domain reflectometer
- 20 pre-set cable types
The cable fault meter represents a powerful and versatile measuring instrument specifically designed for the precise measurement of electrical cables and conductors. With an impressive measurement range from 0.1 meters to an astonishing 30 kilometers, this device can measure and display cable lengths. Since the cable fault meter determines length based on conductor resistance, it can also measure resistance from 0.1 mΩ to 1999.9 Ω.
- Cable Length: 0.1 m ... 30 km
- Standard Cable Types: Selectable from 0.15 ... 240 mm²
The cable locator is a versatile measuring instrument. In addition to the standard voltage and current measurements, the cable locator also has a network analysis. With this network analysis, the cable locator can be used to check, for example, LAN connections for their correct wiring and function.
Measurement function:
- AC voltage
- DC voltage
- AC
- DC
- Resistance
- Diode measurement
- Continuity test
ISO calibration certificate, e.g. to comply with your DIN ISO 9000. For this we give the measuring device to our in-house calibration laboratory. You as the client, the measured values and the serial number are recorded in this ISO calibration certificate.
N.B. calibration certificates are issued specifically for the customer and are non-returnable.
PCE Instruments offers a wide range of stock products. However, despite an extensive selection of stock product offerings, sometimes a custom product is required to satisfy the specific requirements of a new, groundbreaking or special application.
Are you looking for custom test instruments?
Look no further than PCE Instruments. The DIN EN ISO 9001-certified PCE Product and Development Company GmbH produces customized test instruments tailored to meet the unique needs of a diverse customer base. By capitalizing on the expert knowledge and extensive experience of PCE’s industry-leading engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
Throughout the design, development and production process, PCE's engineers and technicians work hand-in-hand with each customer to ensure the final test instrument exceeds expectations. Specifications are clearly defined from the start of the project. Sensors, microprocessors and other electronic components are sourced from high-quality suppliers. Software is written to best support the customer's systems, processes and procedures. Qualified calibration laboratories are tasked with verifying the measurement accuracy of the custom test instrument, and rigorous testing is conducted to make certain that the device will function properly under the anticipated operating conditions.
If you are interested in pursuing the creation of a custom test instrument designed to accommodate an unusual or highly specialized measuring task, please contact the friendly and knowledgable staff at info@industrial-needs.com or +44 (0) 2380 987 035 for PCE Instruments UK, or at info@pce-americas.com or +1 (561) 320-9162 for PCE Americas Inc.
engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
