Industrial Measurement Products and Solutions

Current Indicator

Order no.: PCE-N25Z
The digital indicator PCE-N25Z can be used for processing different AC input signals. Depending on your specific needs, the digital indicator can be ordered with different inputs, like 100 V AC, 250 V AC, 400 V AC, 1 A AC, 5 A AC and 20...50 Hz. The input signal of the digital indicator is freely scalable, which increases its application possibilities.

- IP65 protected front
- 6 different inputs available
- configuration via software
- 5-digit LED display

Manufacturer: PCE Instruments
US$ 117.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-N25H

The digital indicator PCE-N25H is used for measuring and displaying direct current and direct voltage. Depending on your specific needs, the digital indicator can be ordered with different inputs, such as ±100 V DC, ±250 V DC, ±400 V DC, ±1 A, ±5 A, 0...100 V DC or 0...250 V DC. The input signal of the digital indicator is freely scalable, which increases its application possibilities.


- 7 different input options
- Accuracy: ± (0.2 % FS + 1 digit)
- Configuration via software
- 5-digit LED display

 

Manufacturer: PCE Instruments
US$ 120.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-N30H

The digital indicator PCE-N30H can measure direct voltage up to 500 V and direct current up to 5 A. This makes the digital indicator an ideal device, when it comes to monitoring of direct current. The measured values are shown on the large LED display of the PCE-N30H.


- Measuring range: ±100 / ±500 V DC; ±1 /±5 A DC
- Display range: -19,999 ... +99,999
- 21-point scaling
- IP 65 protection on the front

 

Manufacturer: PCE Instruments
US$ 143.55

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-N30B

The installation display PCE-N30B is a Modbus Master for up to 10 slave devices. This indicator can trigger, as well as display readings, trigger alarms, share readings, and save readings. The installation display PCE-N30B is used as a Modbus master in a Modbus network which enables the display to process multiple Modbus slaves that can be cycled through at the push of a button.


- Front Side IP 65
- Setting via Front Key
- Two Alarm Outputs
- Modbus master and slave 

 

Manufacturer: PCE Instruments
US$ 184.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-N30P

The digital indicator PCE-N30P can determine the most important system parameters of a single-phase network. Based on the current and voltage, the digital indicator PCE-N30P calculates the apparent, active and reactive power, as well as the phase difference angle and the power factor. The digital indicator can also determine the average power for a 15 minute period and the average voltage for a 10 minute period.


- Input: 0.02...6 A / 0...480 V / 45.00...100.00 Hz
- Accuracy: 0.2 %
- IP65 protected front
- Two alarm outputs

 

Manufacturer: PCE Instruments
US$ 206.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-ND10
The current indicator PCE-ND10 measures all 3-phase network parameters. Power, voltage, and power measurements are not a problem for the PCE-ND10 power indicator. 

 

- Detection of wrong phase sequence
- Pulse output of the effective energy
- IP 65 on the front
- Voltage supply via measuring connections
- Different variants can be selected! Note: This item must be configured before ordering!

Manufacturer: PCE Instruments
US$ 222.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer