Control Systems

The digital panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

• IP65 protected front
• For thermocouples and resistance thermometers
• Configuration via software
• 5-digit LED display

The digital temperature indicator is used for processing signals coming from temperature sensors. Depending on your specific needs, the temperature indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the temperature indicator is freely scalable, which increases its application possibilities.

• IP65 protected front
• For thermocouples and resistance thermometers
• Configuration via software
• 5-digit LED display

• Illuminance: 0 ... 65535 lx
• Resolution: 1 lx - Accuracy: ±7 % FS @25°C / 77°F
• Protection class: IP65
• Output: RS-485 Modbus RTU*

The panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: PT100, Thermoelement Type J / K (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

• Frequency Indicator mode
• DC voltage: 0 ... 999.9 V
• AC voltage: 0 ... 750 V
• direct current: 0 ... 10 A
• alternating current 0 ... 10 A
• frequency: 40 Hz ... 1 kHz
• resistance: 0 ... 99.99 MΩ
• capacitance: 0 ... 99.99 mF
• temperature: -20 ... +1000 °C
• graphical display of the measured value

• 2-channel Frequency Indicator
• bandwidth: 10 MHz, sampling rate: 50 MS/s
• voltage: 0 ... 1000 V DC, 0 ... 750 V AC
• current: 0 ... 9.999 A AC/DC
• resistance, capacitance, temperature
• non-contact voltage detection
• signal generator: 1 Hz ... 2 MHz

The digital temperature indicator PCE-N24T is used for processing signals coming from temperature sensors. Depending on your specific needs, the digital indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the digital indicator is freely scalable, which increases its application possibilities.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: PT100, Thermoelement Type J / K (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

The panel meter is used for the signal processing of 4 .. 20 mA. The panel meter has a 5-digit LED display to allow the user to read the directly measured current values.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: 0/4 … 20 mA, 0 … 60 mV, ±60 mV DC, 0 … 10 V, ± 10 V DC (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

The digital universal indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the digital universal indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the digital universal indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The frequency indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the frequency indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the frequency indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

PCE-N20U is a frequency indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The panel indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the panel indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the panel indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a panel indicator used for signal processing. Designed for quick and easy system integration, the digital panel indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The panel indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The PCE-N20U is a power indicator used for signal processing. Designed for quick and easy system integration, the digital power indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The power indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The pressure indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the pressure indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the pressure indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a pressure indicator used for signal processing. Designed for quick and easy system integration, the digital pressure indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The pressure indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The process indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the process indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the process indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a process indicator used for signal processing. Designed for quick and easy system integration, the digital process indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The process indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The digital temperature indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the digital temperature suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the digital temperature.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The digital temperature indicator is used for processing signals from Pt100 temperature sensors or thermocouples (type J, K). The measurement results are shown on the large 5-digit LED-display of the temperature indicator. Depending on the actual values, the temperature can be shown in three different colors, which makes it easier to evaluate them.

• Input: Pt100, thermocouple type J or type K
• Accuracy: ± (0.2 % FS + 1 dgt.)
• two open collector outputs
• 24 V power supply sytem for sensors and transducers
• 5-digit, three-coloured LED display

The PCE-N20U is a digital temperature indicator used for signal processing. Designed for quick and easy system integration, the digital temperature indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The temperature indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The voltage indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the voltage indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the voltage indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The PCE-N20U is a voltage indicator used for signal processing. Designed for quick and easy system integration, the digital voltage indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The voltage indicator also can output signals via two open collector outputs when a threshold value is exceeded.

• Input (selectable): 0…10 V / 0…60 mV / ±10 V
• Accuracy: ± (0.2 % FS + 1 digit)
• 24 V power supply system for sensors and transducers

The humidity sensor is used in HVAC technology to monitor humidity and temperature. The measured values are output as a standard signal by the humidity sensor . Air humidity and temperature are accurately determined in this compact humidity sensor via a semiconductor component. For commissioning, the humidity probe is supplied with a DC voltage. The measured values are output via a two-wire cable.

• With display
• Standard signal output
• Simple wall mounting
• RS-485 interface