Panel Meter

US$ 277.00

ex. VAT, ex. delivery costs

The panel meter measures current up to 63 A directly. This makes it possible to connect the power display directly to the main distribution. The panel meter measures all relevant network parameters such as current, voltage, power and frequency. The panel meter is ideally suited for measurement purposes in order to comply with the ISO 50001 energy management standard.

Measures up to 63 A directly

Measuring about 1A / 5A transducer possible

Measurement of U, I, f, P

DIN rail

Panel Meter PCE-PA 5500

US$ 198.00

ex. VAT, ex. delivery costs

The panel meter is a compact instrument for measuring and displaying various grid parameters in three-phase grids. This panel meter can record the energy values of individual consumers or electrical feeders. In addition to the voltages and currents, the apparent, reactive and active power as well as the active and reactive energy are measured and shown on the 68 x 55 mm display.

AC voltage: 30 … 264 V
Alternating current direct: 0.025 mA … 5 A
Energy meter
Harmonics up to the 50th order
RS485 Modbus interface
Accuracy class: 0.5

Panel Meter PCE-N24H

US$ 119.00

ex. VAT, ex. delivery costs

The digital panel meter is is used to show DC voltage parameters. The panel meter can measure and display direct current, direct voltage. The possibility of freely scaling the input signal allows a very versatile use of this panel meter.

Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
Input signal: ±100 V DC, ±250 V DC, ± 400 V DC, 1 A DC, 5 A DC (selectable)
Display: 4 digits, red
Digit height: 20 mm / 0.78"Note: This item must be configured before ordering!

Panel Meter PCE-N24Z

US$ 122.00

ex. VAT, ex. delivery costs

The panel meter is used to display AC parameters. The panel meter can measure and display AC current, AC voltage or frequencies. The possibility of freely scaling the input signal allows a very versatile use of this panel meter.

Power supply: 230V, 110V, 24V, 20 … 40V AC/DC, 85 … 253 V AC/DC (selectable)
Input signal: 1 … 100V, 2.5 … 250V, 4 … 400V, 20 … 500 Hz, 1 A, 5 A (selectable)
Display: 4 digits, red
Digit height: 20 mm / 0.78"

Panel Meter PCE-N25S

US$ 125.00

ex. VAT, ex. delivery costs

The panel meter is used for processing standardised signals. Depending on your specific needs, the panel meter can be ordered with different inputs, such as 0…20 mA, 4…20 mA, 0…60 mV, 0…10 V, ±60 mV or ±10 V. The input signal of the panel meter is freely scalable, which increases its application possibilities.

IP65 protected at the front
6 different standardised signal inputs available
configuration via software
5-digit LED display

Panel Meter PCE-N25T

US$ 125.00

ex. VAT, ex. delivery costs

The digital panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

IP65 protected front
For thermocouples and resistance thermometers
Configuration via software
5-digit LED display

Panel Meter PCE-N50B

US$ 131.00

ex. VAT, ex. delivery costs

The panel meter has a RS485 Modbus interface. This digital Modbus panel meter can display the measured data of up to 10 slave devices or registers.

Interface: RS 485 Modbus RTU Master
Number of slave devices / registers: 10
Baud rate individually adjustable
Further power supply area

Panel Meter PCE-N24T

US$ 132.00

ex. VAT, ex. delivery costs

The panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
Input signal: PT100, Thermoelement Type J / K (selectable)
Display: 4 digits, red
Digit height: 20 mm

Panel Meter PCE-N24S

US$ 134.07

ex. VAT, ex. delivery costs

The panel meter is used for the signal processing of 4 .. 20 mA. The panel meter has a 5-digit LED display to allow the user to read the directly measured current values.

Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
Input signal: 0/4 … 20 mA, 0 … 60 mV, ±60 mV DC, 0 … 10 V, ± 10 V DC (selectable)
Display: 4 digits, red
Digit height: 20 mm

Panel Meter PCE-N30O-1

US$ 139.00

ex. VAT, ex. delivery costs

Two counters / tri-color digital display / 2 alarm relays / freely scalable / 2 control inputs / optional analog output and RS-485 / front 65 IP.

2 internal counters
Front IP 65
3 colour indication display
2 alarm outputs

Panel Meter PCE-N30O-2

US$ 139.00

ex. VAT, ex. delivery costs

Two counters / tri-color digital display / 2 alarm relays / freely scalable / 2 control inputs / optional analog output and RS-485 / front 65 IP.

2 internal counters
Front IP 65
3 colour indication display
2 alarm outputs

Panel Meter PCE-PA39

US$ 145.00

ex. VAT, ex. delivery costs

The panel meter is designed to monitor AC power. This analogue indicator can be installed onto switch panels. The panel meter is a moving-coil ammeter. Active power as well as apparent power can be measured by means of this panel meter.

Moving-coil meter to measure electric power
96 x 96 mm
Panel installation

Panel Meter PCE-N20I

US$ 165.00

ex. VAT, ex. delivery costs

The panel meter is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the panel meter suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the panel meter.

Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
Accuracy: ± (0.2 % FS + 1 dgt.)
Two open collector outputs
24 V power supply sytem for sensors and transducers

Panel Meter PCE-N20T

US$ 165.00

ex. VAT, ex. delivery costs

The digital panel meter is used for processing signals from Pt100 temperature sensors or thermocouples (type J, K). The measurement results are shown on the large 5-digit LED-display of the panel meter. Depending on the actual values, the temperature can be shown in three different colors, which makes it easier to evaluate them.

Input: Pt100, thermocouple type J or type K
Accuracy: ± (0.2 % FS + 1 dgt.)
two open collector outputs
24 V power supply sytem for sensors and transducers
5-digit, three-coloured LED display

Panel Meter PCE-N20U

US$ 165.00

ex. VAT, ex. delivery costs

The PCE-N20U is a panel meter used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The panel meter also can output signals via two open collector outputs when a threshold value is exceeded.

Input (selectable): 0…10 V / 0…60 mV / ±10 V
Accuracy: ± (0.2 % FS + 1 digit)
24 V power supply system for sensors and transducers

Panel Meter PCE-N20Z

US$ 171.00

ex. VAT, ex. delivery costs

The panel meter can be used to measure AC voltages up to 400 V and AC currents. The voltage to be measured is connected directly and can then be read on the 5-digit LED display of the panel meter.

Input: 1A AC, 5A AC, 100V AC, 250V AC, 400 V AC, 20 … 500 Hz (selectable)
Supply voltage: 85 … 253V AC/DC / 20 … 40 V AC/DC (selectable)
Display: 5 digits, three colors
Digit height: 14 mm / 0.55"

Panel Meter PCE-N30O-3

US$ 211.00

ex. VAT, ex. delivery costs

Two counters / tri-color digital display / 2 alarm relays / freely scalable / 2 control inputs / optional analog output and RS-485 / front 65 IP.

2 internal counters
Front IP 65
3 colour indication display
2 alarm outputs

Panel Meter PCE-N30O-4

US$ 211.00

ex. VAT, ex. delivery costs

Two counters / tri-color digital display / 2 alarm relays / freely scalable / 2 control inputs / optional analog output and RS-485 / front 65 IP.

2 internal counters
Front IP 65
3 colour indication display
2 alarm outputs

Panel Meter PCE-DPD-U

US$ 237.00

ex. VAT, ex. delivery costs

The panel meter can be configured as AC and DC voltmeters (up to 600 Vac / DC), AC and DC ammeters (up to 5 AAC / DC). Furthermore, the built-in display shows measured values of process signals (mA, VDC), thermocouples, resistive temperature sensors (Pt, Ni, PTC and NTC), resistors, potentiometers and frequency.

Input:
2-, 3- wire
Thermocouples
Potentiometer
Resistance
Process signals
Frequency
DC voltage
DC power
AC voltage
AC power

Panel Meter PCE-N30U

US$ 249.00

ex. VAT, ex. delivery costs

The panel meter can process several different input signals, such as 0…410/4010 Ohm, -10…+63 mV DC, -13…+13 V DC, -24…+24 mA DC or signals from thermocouples and resistance thermometers. This makes the panel meter applicable in a wide range of applications. The measured values are shown on the large LED display of the panel meter.

21-point scaling
IP 65 protection on the front
Three-colored display
Two alarm outputs

Panel Meter PCE-N30P

US$ 269.00

ex. VAT, ex. delivery costs

The panel meter can determine the most important system parameters of a single-phase network. Based on the current and voltage, the panel meter calculates the apparent, active and reactive power, as well as the phase difference angle and the power factor. The panel meter can also determine the average power for a 15 minute period and the average voltage for a 10 minute period.

Input: 0.02…6 A / 0…480 V / 45.00…100.00 Hz
Accuracy: 0.2 %
IP65 protected front
two alarm outputs

Panel Meter PCE-DPD-F1

US$ 434.00

ex. VAT, ex. delivery costs

The built-in display is used to indicate the force and weight, which is detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

Power supply: 85 … 265V AC / DC
Input signal: mV / V for force and weighing sensors
Display: 6 digits, red
Digit height : 14 mm

Panel Meter PCE-DPD-F2

US$ 450.00

ex. VAT, ex. delivery costs

The built-in display is used to indicate the force and weight, which is determined by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

Power supply: 11 … 60V DC / 24/48V AC
Input signal: mV / V for force and weighing sensors
Display: 6 digits, red
Digit height : 14 mm

Panel Meter PCE-G 2

US$ 647.00

ex. VAT, ex. delivery costs

The panel meter is used to measure the environmental parameters of temperature and humidity. The panel meter is used in warehouses, open-plan offices, schools, etc.

Measuring range temperature: -40 … 85 °C
Measuring range humidity: 0 … 99 % r.H.
55 mm character height
Up to 30 m reading distance
External sensor (wired)

Panel Meter PCE-N45F

US$ 669.00

ex. VAT, ex. delivery costs

The panel meter is used to realize individual weighing solutions. The panel meter can be used to connect load cells, force sensors, weighing platforms and other sensors that use strain gauges.

Signal input range: 0 … 10 mV / 0 … 15 mV
Supply voltage of the measuring cell: 5V
Power supply: 24V DC
Relay output
Potential-free digital input
Interface and analog output

Panel Meter PCE-ULM 10

US$ 734.00

ex. VAT, ex. delivery costs

The panel meter is the ideal measuring device to determine the fill level of a silo. Thanks to the 4 … 20-mA output signal, the panel meter can also be connected to the operational process control.

Measuring range: 0 … 10 m / 0 … 32.8 ft
Accuracy: 0.5%
Resolution: 0.001 m
With display for setting and reading
Stable M60 connection thread

Panel Meter PCE-N50F

US$ 913.00

ex. VAT, ex. delivery costs

The panel meter is suitable for panel mounting. This panel meter can be used to indicate the weight, force or torque. The decisive factor here is the type of sensor that is connected to the panel meter.

Signal input range: 0 … 20 mV
Units: g, mN, mlb, Pa, kg, N, Ib, kPa, t, kN, klb, MPa
For load cells, force sensors, etc.
Up to 1600 Hz sampling rate
LCD display

Panel Meter PCE-ULM-10-N24S

US$ 932.00

ex. VAT, ex. delivery costs

The panel meter is the ideal measuring device to determine the filling level of a silo. Thanks to the 4 … 20 mA output signal, the panel meter can also be connected to the operational process control.

Measuring range: 0 … 10 m / 0 … 32.8 ft
Accuracy: 0.5%
Resolution: 0.001 m
With display for setting and reading
Stable M60 connection thread
incl. external digital display PCE-N24S:
Voltage supply: selectable
Input signal: selectable
Display: 4 digits, red
Digit height: 20 mm / 0.78"

Panel Meter PCE-BPD-U-46A

US$ 999.00

ex. VAT, ex. delivery costs

The panel meter is designed in such a way that the measured values displayed can be read from a large distance. With a digit height of 60 mm or 100 mm (2.3" or 3.9"), the reading distance for panel meters is 25 m or 50 m (82 ft or 164 ft).

Function: convert analog signal into usable value
Input signal: 4 … 20 mA, ±20 mA DC, 0 … 10 V DC, ±10 V DC
Display range: -1999 … 9999
Digit height: 60 mm / 2.3"
Number of outputs: 2
Voltage supply: 85 … 265 V AC / 120 … 370 V DC

Panel Meter PCE-BPD-U-46D

US$ 999.00

ex. VAT, ex. delivery costs

Function: convert analog signal into usable value
Input signal: 4 … 20 mA, ±20 mA DC, 0 … 10 V DC, ±10 V DC
Display range: -1999 … 9999
Digit height: 60 mm / 2.3"
Number of outputs: 2
Voltage supply: 11 … 36 V DC

Panel Meter PCE-BPD-C-66D

US$ 1,188.00

ex. VAT, ex. delivery costs

The panel meter is designed in such a way that the readings displayed can be read from a long distance. With a digit height of 60 mm or 100 mm (2.3" or 3.9"), the reading distance for the display is 25 m or 50 m (82 ft or 164 ft).

Function: time measurement
Input signal: NPN, PNP
Display range: -199,999 … 999,999
Number of outputs: 3
Voltage supply: 11 … 36 V DC

Panel Meter PCE-BPD-P-66A

US$ 1,188.00

ex. VAT, ex. delivery costs

Function: convert frequency to a usable value
Input signal: NPN, PNP
Display range: -199,999 … 999,999
Number of outputs: 3
Voltage supply: 85 … 265 V AC / 120 … 370 V DC

Panel Meter PCE-BPD-P-66D

US$ 1,188.00

ex. VAT, ex. delivery costs

Function: convert frequency to a usable value
Input signal: NPN, PNP
Display range: -199,999 … 999,999
Number of outputs: 3
Voltage supply: 11 … 36 V DC

Panel Meter PCE-G1

US$ 1,452.00

ex. VAT, ex. delivery costs

The panel meter is intended for stationary measurement of relative humidity and temperature and direct display on a large display. This panel meter consists of an LED display (100 mm high) and is protected according to IP 54.

Temperature measuring range: 0 … +60 °C (Celsius only)
Humidity measuring range: 10 … 95 % RH
Up to 50 m (164 ft) reading distance
External sensor (wired)

Panel Meter PCE-G1A

US$ 1,460.00

ex. VAT, ex. delivery costs

The Panel meter is a measuring device for stationary measurement of relative humidity and temperature. This panel meter consists of an LED seven-segment display with a digit height of 100 mm, which enables you to read it very well even at a distance of up to 50 m.

Temperature measuring range: 0 … +60 °C (Celsius only)
Humidity measuring range: 10 … 95 % RH
Up to 50 m (164 ft) reading distance
External sensor (wired)
Voltage supply: 230 V AC
with analogue output 4 … 20 mA

Panel Meter PCE-BPD-U-41A

US$ 1,521.00

ex. VAT, ex. delivery costs

Function: convert analog signal into usable value
Input signal: 4 … 20 mA, ±20 mA DC, 0 … 10 V DC, ±10 V DC
Display range: -1999 … 9999
Digit height: 100 mm / 3.9"
Number of outputs: 2
Voltage supply: 85 … 265 V AC / 120 … 370 V DC