Condition Monitoring
Order no.: PCE-ODM 12
This PCE-ODM 12 condition monitoring voltmeter features both automatic and manual ranging and a dual OLED display. The measured values are displayed on the OLED number display up to 6,000 digits and in the bar graph.
Measuring function
- DC DC
- AC voltage AC (TRMS)
- AC + DC TRMS voltage
- DC DC
- AC AC (TRMS)
- 4 ... 20-mA %
- AC AC / Rogowski coil
- Resistance
- Frequency
- Duty cycle
- Capacity
- Temperature / thermocouple
- Interface: Bluetooth BLE
Manufacturer: PCE Instruments
Order no.: PCE-PI 10
The condition monitoring digital multimeter PCE-PI 10 is used to determine the direction of rotation of 3-phase voltage networks. Furthermore, the condition monitoring digital multimeter is able to measure voltages up to 600V AC / DC. The rotating field direction is important for machines and plants.
- Measuring range: 75 ... 600V AC
- 3-phase rotating field detection
- AC / DC voltage measurement
- CAT III 600V
Manufacturer: PCE Instruments
Order no.: PCE-T 238
The condition monitoring tachometer PCE-T 238 is a battery-powered hand-held device that allows mobile use.
The condition monitoring tachometer can perform a contact measurement as well as a non-contact measurement.
It is also possible to perform a measurement of the surface velocity. The condition monitoring tachometer allows a measurement of up to 99,999 revolutions per minute.
This measuring range is possible with contactless measurements with the optical tachometer.
- Continuous data output
- Contactless measurement range: 0 ... 99,999 RPM
- Contact measurement range: 0.5 ... 19,999 RPM
- Surface measurement range: 0.05 ... 1,999.9 m/min
- Measuring distance without contact: 5 ... 150 cm / 1.9" ... 4.9 ft
- Measuring distance without contact: 5 ... 150 cm / 1.9" ... 4.9 ft
Manufacturer: PCE Instruments
Order no.: PCE-T390
The PCE-T390 Condition Monitoring Thermometer is a digital device with four input channels for type K and type J temperature sensors and two input channels for PT100 temperature sensors. The PCE-T390 Condition Monitoring Thermometer has a SD card slot (from 1 ... 16 GB) for storing the measured data. The data is stored in xls format on the SD card of the contact thermometer so that no additional software is needed for further analysis.
- 4 input channels for type-K, J temperature sensors
- 2 input channels for Pt100 temperature sensors
- 2 x type-K TF-500 temperature sensors are included in the package
- SD card memory (1 ... 16 GB)
Manufacturer: PCE Instruments
Order no.: PCE-SLM 10
The condition monitoring sound level meter PCE-SLM 10 is suitable for the continuous measurement and visualization of the sound pressure level. The condition monitoring sound level meter PCE-SLM 10 is used in schools, open-plan offices, bars, clubs and other event rooms. Micro USB powered via external charger or battery pack.
- 75 mm / 3 in digit height
- 30 ... 130 dBA measuring range
- 0.1 dB or 1 dB resolution
- For offices, schools, event rooms
- Memory for 657,000 readings
Manufacturer: PCE Instruments
Order no.: PCE-VT 1100
The condition monitoring vibration meter is used as a hand-held measuring device for the individual assessment of vibrations on machines and systems. With the help of this condition monitoring vibration meter, the actual state can easily be determined on site. Thus, corresponding changes can be made directly on site after the measurement.
- Frequency range: 10 Hz ... 1 kHz
- Measures speed, distance, acceleration in metric units
- Holds the reading after each measurement
- Easy to handle and battery operated
- Standard probe: 10mm
Manufacturer: PCE Instruments
Order no.: PCE-313A
The PCE-313 A Thermometer measures relative humidity and temperature and can be used in the air-conditioning sector. The PCE-313 A Thermometer can be connected to type K thermo-elements to detect, for instance, the temperature of a wall by means of a surface probe. The internal memory of this test equipment allows the Thermometer to record humidity and temperature data at an adjustable measurement interval. Thanks to its SD memory card (1 to 16 GB) the humidity test instrument can be used for long term data acquisition. The meter comes manufacturer calibrated (ISO or as an option).
- Relative humidity: 5 ... 95% r.H.
- Temperature: 0 ... 50°C / 32 ... 122°F
- Type K: -50 ... 1300°C / -58 ... 2372°F
- Calculated dew point: -25.3 ... 48.9°C / -13.5 ... 120°F
- Wet bulb temperature: -21 ... 50°C / -5.8 ... 122°F
- Memory: SD card (1 ... 16 GB)
Manufacturer: PCE Instruments
Order no.: PCE-SLD 10
The condition monitoring device PCE-SLD 10 is used for permanent monitoring of the sound level. In addition to storing the measured values, the PCE-SLD 10 condition monitoring device is able to display the measured values on a display and output them as a 4 ... 20-mA analog value.
- Measurement accuracy: Based on class 2 according to IEC61672
- Resolution: 0.1 dB
- LC display
- SD card memory up to 16 GB
- external microphone
- Analog output with 4 ... 20-mA
Manufacturer: PCE Instruments
Order no.: PCE-OM 15
PCE-OM 15 is a condition monitoring strobe rotation meter or handheld strobe tachometer with trigger functionality. This easy-to-use portable digital stroboscope gun features high / low range selection and push-button rate control to scale the flash rate slower (x½) and faster (x2). In addition, two knobs allow coarse and fine adjustment of the flash rate.
- Measuring range: 50 ... 30000 rpm
- Bright 6500K xenon light bulb
- 10 mm / 0.4 in 5-digit LCD
Manufacturer: PCE Instruments
Order no.: PCE-DSX 20
The condition monitoring stroboscope PCE-DSX 20 is mostly used for speed or vibration measurement or for motion observations. This condition monitoring stroboscope has a small design and has a low weight. Thus, the tachometer can be conveniently used even in measurements in hard to reach places.
Function
- Speed: 50 ... 35000 RPM / FPM
- Flash frequency
- phase shift
- Lamp type: Xenon flash
- Flash response time: 10 ... 30 μs
- With trigger input
Manufacturer: PCE Instruments
Order no.: PCE-T 238-ICA
The condition monitoring tachometer PCE-T 238 is a battery-powered hand-held device that allows mobile use.
The condition monitoring tachometer can perform a contact measurement as well as a non-contact measurement.
It is also possible to perform a measurement of the surface velocity. The condition monitoring tachometer allows a measurement of up to 99,999 revolutions per minute.
This measuring range is possible with contactless measurements with the optical tachometer.
- Continuous data output
- Contactless measurement range: 0 ... 99,999 RPM
- Contact measurement range: 0.5 ... 19,999 RPM
- Surface measurement range: 0.05 ... 1,999.9 m/min
- Measuring distance without contact: 5 ... 150 cm / 1.9" ... 4.9 ft
- Incl. ISO calibration certificate
- Measuring distance without contact: 5 ... 150 cm / 1.9" ... 4.9 ft
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Order no.: PCE-VS10
PCE-VS10 is a vibration meter, analyzer or sensor condition monitoring switch used to measure RMS and peak value of vibration velocity or acceleration piezoelectrically. This IP67-rated vibration monitoring switch features a red and green visual warning or alarm with programmable high pass and low pass filters.
- Frequency range (max.): 0.1 Hz ...10 kHz
- Measuring range: Acceleration = 0.1 ... 1000 m/s², Speed =
Frequency-dependent
- Connections: Screw terminals for power supply (5 ... 30V DC) and Micro USB (internal)
- Mounting: M8 stud bolt
Manufacturer: PCE Instruments
Order no.: PCE-SLD 10-ICA
The condition monitoring device PCE-SLD 10 is used for permanent monitoring of the sound level. In addition to storing the measured values, the PCE-SLD 10 condition monitoring device is able to display the measured values on a display and output them as a 4 ... 20-mA analog value.
- Measurement accuracy: Based on class 2 according to IEC61672
- Resolution: 0.1 dB
- LC display
- SD card memory up to 16 GB
- external microphone
- Analog output with 4 ... 20-mA
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Order no.: PCE-OM 15-ICA
PCE-OM 15-ICA is a condition monitoring stroboscope with trigger functionality. This easy-to-use portable digital stroboscope gun features high / low range selection and push-button rate control to scale the flash rate slower (x½) and faster (x2). In addition, two knobs allow coarse and fine adjustment of the flash rate.
- Measuring range: 50 ... 30000 rpm
- Bright 6500K xenon light bulb
- 10 mm / 0.4 in 5-digit LCD
- Incl. ISO Calibration Certificate
Manufacturer: PCE Instruments
Order no.: PCE-DSX 20-ICA
The condition monitoring stroboscope PCE-DSX 20-ICA is mostly used for speed or vibration measurement or for motion observations. This condition monitoring stroboscope has a small design and has a low weight. Thus, the tachometer can be conveniently used even in measurements in hard to reach places.
Function
- Speed: 50 ... 35000 RPM / FPM
- Flash frequency
- phase shift
- Lamp type: Xenon flash
- Flash response time: 10 ... 30 μs
- With trigger input
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Order no.: PCE-894
The condition monitoring thermometer PCE-894 with double laser has a temperature range of -50 ... 1850°C / -58 ... 3362°F. The condition monitoring thermometer PCE-894 has an optical resolution of 50: 1 and enables a precise, non-contact temperature measurement of very small areas.
- Temperature range from -50 ... 1850°C / -58 ... 3362°F
- Adjustable emissivity
- Short response time of 150 ms
- With thermocouple input
- Bluetooth interface
Manufacturer: PCE Instruments
Order no.: PCE-LES 100
The PCE-LES 100 Rotation Meter combines LED technology with compact and accurate electronics, which controls the sequence and timing of flash over the entire measuring range. Thanks to LED technology, the Rotation Meter does not need periodic changing of bulbs. The Rotation Meter is sent to you calibrated (by the manufacturer PCE Instruments).
- Range: 60 ... 99,990 r.p.m / 1 ... 1,666 Hz
- Display: 5 digits LCD
- Impulses/Flash: Possibility of duplication and division/fine tuning
- Offset: Yes, 360º
Manufacturer: PCE Instruments
Order no.: PCE-VS11
PCE-VS11 is a vibration meter, analyzer or sensor condition monitoring switch used to measure RMS value, peak value and frequency domain (FFT) of vibration velocity or acceleration piezoelectrically. This IP67-rated vibration monitoring switch features a red and green visual warning or alarm with programmable high pass and low pass filters.
- Frequency range (max.): 0.1 Hz ...10 kHz
- Measuring range: Acceleration = 0.1 ... 1000 m/s², Speed =
Frequency-dependent
- Connections: Screw terminals for power supply (5 ... 30V DC) and Micro USB (internal)
- Mounting: M8 stud bolt
Manufacturer: PCE Instruments
Order no.: PCE-VS12
PCE-VS12 is a vibration meter, analyzer or sensor condition monitoring switch used to measure RMS value, peak value and frequency domain (FFT) of vibration velocity or acceleration piezoelectrically. This IP67-rated vibration monitoring switch features an external USB port, 8-pin female connector 711 and programmable high pass and low pass filters.
- Frequency range (max.): 0.1 Hz ...10 kHz
- Measuring range: Acceleration = 0.1 ... 1000 m/s², Speed =
Frequency-dependent
- Connections: Screw terminals for power supply (5 ... 30V DC) and Micro USB (internal)
- Mounting: M8 stud bolt
Manufacturer: PCE Instruments
Order no.: PCE-VT 2800
The PCE-VT 2800 Condition Monitoring Vibration Meter measures acceleration, oscillation speed and shift of vibrating parts, machines and equipment. The device features an integrated data logger to record vibration measurements over time. Measurement data is stored on an SD card memory and can be transferred directly to a PC via USB or RS-232 interface.
- Handheld instrument with vibration data logging function
- Frequency range: 10 Hz ... 1 KHz
- True-RMS (TRMS), max-hold, data-hold and peak-value
functionality
- Adjustable sampling rate
Manufacturer: PCE Instruments
In manufacturing and industrial environments, it is not only desirable for people to work effectively, but also for production equipment to work 
effectively. Equipment should be maintained so that downtime due to defective machine components hardly ever occurs. Condition monitoring attempts to predict machine behaviors, starting with a machine's control technology all the way through to the individual machine components. The goal of condition monitoring is to replace components shortly before they stop working, rather than replacing components after a certain period of time.
It is crucial to know the condition of production machines in all areas of industry and to recognize possible sources of error at early stages to be able to plan scheduled maintenance in good time. Additionally, when important machine components are used to the maximum, tremendous cost savings can be realized.