Environmental Tester

- Range : 30 ... 130dB (A)
- Resolution: 0.1dB
- Accuracy: ± 1.5dB
- Alarm relay: 5A / 240VAC
- Supply: 250V / 50Hz
- Handle and wall mount
- Analogue output signal
- Incl. ISO calibration certificate

The environmental tester is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the environmental tester determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 2.5 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

- Measuring range up to 30,000 G
- DC Milli Tesla, DC Gauss, Transverse Probe
- AC Milli Tesla, AC Gauss, frequency from 40 to 500 Hz
- Temperature sensor
- Switchable AC or DC measurement
- Memory: Manual / Automatic
- Incl. ISO calibration certificate

The PCE-WP24 is a environmental tester used to perform noninvasive, nondestructive moisture measurements of wood, timber and other construction or building materials. An ideal tool for assessing everything from lumber to floors and more, this environmental tester uses electromagnetic waves that penetrate approximately 50 mm / 1.96 inches to 60 mm / 2.36 inches deep (depending on substrate) to return a mean-value moisture content percentage.

- Moisture content measuring range: 4% ... 60% wood, 0% ... 10% building
  materials
- Resolution: 0.1%
- Accuracy: ±0.7%

 

Measuring function
- PM2.5
- Humidity
- Temperature
- CO2
- Air pressure
- Memory: SD card max. 32 GB
- Ideal for workplace monitoring
- Alarm function

- Temperature measuring range: 32.0… 122.0 °F
- Humidity measuring range: 0.0 ... 99.9% RH
- Connection of up to four external sensors
- Analog 4 ... 20-mA input signal
- Wall mounting

- Measuring range: 70 ... 140 dB
- Frequency weighting: A, B and Z
- Battery life: >15 hours
- LEQ measurement
- Memory
- USB interface
- Battery / power supply
- Software download
- Standards: IEC 61252:2002, ANSI S1.25-1991

- Temperature measuring range: 32.0… 122.0 °F
- Humidity measuring range: 0.0 ... 99.9% RH
- Connection of up to four external sensors
- Analog 4 ... 20-mA input signal
- Wall mounting
- Incl. ISO calibration certificate

- Dew point, H2O, temperature, humidity measurement
- Data memory for approx. 50,000 measurement data
- CSV data export
- With G1 / 2" connection thread
- For inline measurement of pressure pipes
- Sensor protected with a cap
- Left connection has NO function

The environmental tester is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the environmental tester determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

The environmental tester is intended for stationary measurement of relative humidity and temperature and direct display on a large display. This environmental tester consists of an LED display (100 mm high) and is protected according to IP 54.

- Temperature measuring range: 0 ... +60 °C (Celsius only)
- Humidity measuring range: 10 ... 95 % RH
- Up to 50 m (164 ft) reading distance
- External sensor (wired)

The environmental tester is a measuring device for stationary measurement of relative humidity and temperature. This environmental tester consists of an LED seven-segment display with a digit height of 100 mm, which enables you to read it very well even at a distance of up to 50 m.

- Temperature measuring range: 0 ... +60 °C (Celsius only)
- Humidity measuring range: 10 ... 95 % RH
- Up to 50 m (164 ft) reading distance
- External sensor (wired)
- Voltage supply: 230 V AC
- with analogue output 4 ... 20 mA

- Dew point, H2O, temperature, humidity measurement
- Data memory for approx. 50,000 measurement data
- CSV data export
- With G1 / 2" connection thread
- For inline measurement of pressure pipes
- Sensor protected with a cap
- Left connection has NO function
- incl. ISO Calibration Certificate for humidity and temperature

- Measuring range: 0 ... 12 A DC
- Three different test functions
- PC interface for data transfer
- Switchable graphic view
- Application, e.g. photovoltaic systems

PCE-EM 30 is a digital portable 3-axis environmental electromagnetic radiation tester or EMF detector used to measure electromagnetic radiation generated by electronic devices and electric installations. This triple-axis EMF meter provides greater precision than single-axis models as well as affords the ability to assess EMFs from more than one source at a time.

- Measuring range: 0 to 199.99 V/m, 0 to 99.999 W/m², 0 to 9.9999 mW/cm²
- EMF bandwidth: 100 kHz to 3 GHz
- Measures EMF of 5G cellular Low-band and Mid-band
- Comes with two external sensor probes (for low and high frequency ranges)