The electrical tester has a measuring range of 0 … 1000 A AC/DC. The current is measured inductively using the clamp on the measuring device. Live supply lines with a diameter of up to 32 mm (1.2") can be connected to the electrical tester.

- Measuring range: 0 ... 1000 A AC/DC
- Bluetooth interface
- Inrush current measurement
- LC color display
- Not Connected Voltage function

- Current measurement up to 1000 A
- Cover of the measuring sockets
- Voltage measurement up to 600V
- Temperature measurement via 2 thermocouples
- Bluetooth interface

The PCE-ITE 50 is a robust Electrical Tester with a large 3.5" TFT color LCD display. The Electrical Tester also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

Measuring function
- Current measurement AC
- Inrush current AC
- Voltage measurement DC
- Voltage measurement AC
- Frequency measurement
- Frequency measurement current measurement function
- Frequency measurement voltage measurement function
- Duty cycle
- Resistance measurement
- Continuity test
- Capacity measurement
- Diode measurement
- Single-phase power measurement
- Power factor capacitive / inductive
- Harmonics measurement

- Noise level range: Auto 30 ... 130 dB
- Resolution: 0.1dB
- Accuracy: ±1.4dB
- Frequency range: 31.5 Hz...8 kHz
- Frequency Rating: A and C
- Data interface: USB, Bluetooth 4.0
- Free app
- Accuracy class: IEC61672-1 Class 2

With the environmental meter it is possible to determine the humidity, ambient, wet bulb and dew point temperature. Measurements up to 60 °C are possible with the environmental meter. The environmental meter can therefore be used universally because of its various measuring functions to determine the ambient conditions.

Measuring ranges:
- Humidity: 0 ... 100% RH
- Ambient temperature: -20 ... 60 °C / -4 ... 140 °F
- Wet bulb temperature: 0 ... 60 °C / 32 ... 140 °F
- Dew point temperature: -20 ... 60 °C / -4 ... 140 °F
- Interface: Bluetooth
- MIN / MAX / HOLD function

With the environmental meter it is possible to determine the humidity, ambient, wet bulb and dew point temperature. Measurements up to 60 °C are possible with the environmental meter. The environmental meter can therefore be used universally because of its various measuring functions to determine the ambient conditions.

Measuring ranges:
- Humidity: 0 ... 100% RH
- Ambient temperature: -20 ... 60 °C / -4 ... 140 °F
- Wet bulb temperature: 0 ... 60 °C / 32 ... 140 °F
- Dew point temperature: -20 ... 60 °C / -4 ... 140 °F
- Interface: Bluetooth
- MIN / MAX / HOLD function
- incl. sinter filter

- Measuring range: ± 13.8 kPa / ± 2 psi / ± 0.14 bar
- Measurement accuracy: ± 0.006 psi (0 ... 0.2 psi)
- Resolution: 6.9 Pa / 0.001 psi / 0.000069 bar
- Android and iOS app
- Bluetooth interface
- 11 different units

With the table-top environmental meter it is possible to carry out quick and precise analysis of the pH concentration of liquid samples. For example, with the environmental meter it is possible to check alkaline solutions, water, wine, milk and many other liquids for the pH content.

- pH measuring range: -2.000 ... +19.999 pH
- Resolution: 0.1 / 0.01 pH
- Measuring range mV: -1999.9 ... +1999.9 mV
- Resolution: 1 mV
- Temperature measuring range: -10 ... +110 °C / 14 ... 230 °F
- Resolution: 0.1 °C
- USB and Bluetooth interface
- Memory for 300 measured values
- Live viewing software
- 3 point calibration

The environmental meter can be used to quickly and precisely analyze liquid samples. Thus, for example, water, alkalis, milk, wine and many other liquids can be checked for their quality with the environmental meter.

Measuring range:
- pH, mV, TDS
- Temperature, conductivity
- Salinity, resistance
- Large 7" touchscreen
- Bluetooth and USB interfaces
- 3 point calibration

- Wind speed measuring range: 0.00 ... 30.00 m / s
- Temperature measuring range: -20 ... 60°C / -4 ... 140° F
- Humidity measuring range: 0 ... 100% RH
- Telescope diameter 12 mm
- 390 mm / 15.4 in telescopic pole
- Bluetooth 4.0 interface

- Infrared measuring range: -40 ... 300°C / -40 ... 572°F
- Sensor measuring range: -40 ... 300°C / -40 ... 572°F
- Charging station with micro USB cable
- Bluetooth interface

- Measuring range: -2.0 ... 20.0 pH
- Measuring range mV: ± 2000.0 mV
- Temperature measuring range: 0 ... 100°C / 32 ... 212°F 
- Bluetooth interface
- Free download of the Android app from the store

The environmental meter has a measuring range of 0.0 … 100.0%. For a measurement, the ball head is positioned on the test object by the environmental meter. This guarantees a non-destructive measurement with the environmental meter. The environmental meter is therefore used, for example, for on-site inspections of buildings, wood and other surfaces.

- Measuring range: 0.0 ... 100.0%
- Resolution: 0.1%
- Measuring depth: 20 ... 40 mm / 0.78 ... 1.57"
- Interface: Bluetooth 4.0
- Free Android and iOS app

The Environmental Meter measures α-, β-, γ- and X-rays and offers a high measurement accuracy and convenient design. Using the integrated Bluetooth interface in the Environmental Meter, the measured values can be sent in real time to a PC and analyzed with the included software.

- Α-, β-, γ- and X-rays
- Bluetooth interface
- Internal memory
- Software Included

 

The environmental meter has a temperature measuring range of -20 ... 60 °C and a humidity measuring range of 0 ... 99.9% RH. The readings from the environmental meter can be read directly on the 2.3" color display.

Temperature measurement
- Measuring range: -20 ... 60 °C / -4 ... 140 °F
Humidity measurement
- Measuring range: 0 ... 99.9% RH
- Data memory for 12800 measuring points
- For mounting on the wall
- WiFi interface