The wind speed alarm controller PCE-WSAC 50W is primarily used to measure and monitor the wind load on cranes or wind turbines. Furthermore, the wind situation can be measured and analyzed before commissioning a wind turbine.

- Measuring range up to 180 km / h
- Input: pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analog output
- Supply voltage: 24V DC
- Ambient temperature -20 ... 70°C / -4 ... 158°F
- units adjustable: km / h, mph, m / s

- Measuring range up to 180 km / h
- Input: Pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analogue output
- Supply voltage: 110 ... 230V AC, 50/60 Hz
- Ambient temperature -20 .. . 70°C / -4 ... 158°F
- Units adjustable: km / h, mph, m / s

The Wind Speed Meter PCE-WSAC 50W is primarily used to measure and monitor the wind load on cranes or wind turbines. Furthermore, the wind situation can be measured and analyzed before commissioning a wind turbine. The high measuring range of up to 50 m/s of the wind speed meter means stormy gusts can also be monitored.

- Measuring range up to 180 km / h
- Input: pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analog output
- Supply voltage: 24V DC
- Ambient temperature -20 ... 70°C / -4 ... 158°F
- units adjustable: km / h, mph, m / s

The Xgard-1-NH3 is a single-gas Gas detector used to warn for gases (Ammonia, NH₃, 0 ... 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ammonia, NH₃, 0 ... 50 ppm)
- Additional display and alarm station
- ATEX or UL approval

The Xgard-1-NH3 is a single-gas Gas Leak Detector used to warn for gases (Ammonia, NH₃, 0 ... 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ammonia, NH₃, 0 ... 50 ppm)
- Additional display and alarm station
- ATEX or UL approval

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Incl. ISO calibration certificate

The PCE-DDM 5 Crane Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 5 Crane Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 5,000 kg / 50 kN / 11,023 lbs
- Resolution: 2 kg / 20 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The PCE-DDM 5 Force Gauge is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 5 Force Gauge is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 5,000 kg / 50 kN / 11,023 lbs
- Resolution: 2 kg / 20 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The PCE-DDM 5 Hanging Scales are the ideal tool for weighing big loads and for measuring strong tensile forces. The hanging scales are delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 5,000 kg / 50 kN / 11,023 lbs
- Resolution: 2 kg / 20 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The Tension Dynamometer PCE-DDM 5 is the ideal tool for weighing big loads and for measuring strong tensile forces. The Tension Dynamometer PCE-DDM 5 is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 5,000 kg / 50 kN / 11,023 lbs
- Resolution: 2 kg / 20 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

 

ZXCON extended is an extra-long consistometer / viscometer used to measure flow rate, viscosity or consistency by Bostwick method. Designed for conducting quick and accurate Bostwick tests of thinner liquids and pastes for compliance with MIL-R-81294D and ASTM F1080-93, this consistometer features:

- Extended scale length of 354 mm
- 75 ml sample size acceptance
- Built-in level and leveling feet
- Engraved 0.5 cm graduations
- Durable, stainless steel construction
- Spring-loaded gate that prevents premature flow

 

The simple design and an absolutely straightforward operation make it possible for the practitioner to use the adhesion tester as an instrument for daily adhesion tests. Using adhesive with rapid curing, the tests can be performed by the user in the shortest possible time.

- Breakout force: 200 kg
- Diameter of base dolly, mm: 15.1 (№ 1) and 19.5 (№ 2)
- Specific breakout force, MPa: Dolly №1 up to 10 MPa (100) Dolly
  №2 up to 6 MPa (60)

 

The Material Surface Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

 

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

 

The Profilometer Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

 

The Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

The Surface Testing Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

 

The PCE-DDM 10WI Force Gauge is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 10WI Force Gauge is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 10000 kg / 100 kN
- Resolution: 5 kg / 50 N
- Units of measurement: kg / t / lbs / N / kN
- Comes without remote control indicator

 

The PCE-DDM 10WI Hanging Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 10WI Hanging Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 10000 kg / 100 kN
- Resolution: 5 kg / 50 N
- Units of measurement: kg / t / lbs / N / kN
- Comes without remote control indicator

 

The Tension Load Cell  PCE-DDM 10WI is the ideal tool for weighing big loads and for measuring strong tensile forces. The Tension Load Cell  PCE-DDM 10WI is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 10000 kg / 100 kN
- Resolution: 5 kg / 50 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control indicator

 

The PCE-DDM 10WI Crane Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 10WI Crane Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 10000 kg / 100 kN
- Resolution: 5 kg / 50 N
- Units of measurement: kg / t / lbs / N / kN
- Comes without remote control indicator