The PCE-830 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm diameter / 2.2 in
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
- Incl. ISO calibration certificate

Force test stand
The motorised force test stand can be used for vertical tensile and compressive force tests. All force gauges from PCE Instruments can be mounted on the force test stand (if necessary with an adapter plate). The force test stand can withstand a maximum load of 500 N.

- Force range: max. 500 N / 50 kg / 110 lb
- Travel path: max. 270 mm / 10.6"
- Feed speed: 1 ... 500 mm/min
- Manual or automatic procedure

Force gauge
Digital force gauge for tensile force measurement and compressive force measurement up to 500 N. The digital force gauge is for precise measurements with a resolution of 0.1 N.

- Measuring range: 0 ... 500 N
- Accuracy: ± 0.1% of the measuring range
- Tensile and compressive force measurement
- 1600 Hz sampling rate
- Interface: USB
- 6 different measuring tips
- Memory for 100 measurements
- 220V AC ONLY

The NDT test Instrument PCE-VE 200SV1 is a nondestructive inspection camera. Thus, the NDT test Instrument is the ideal instrument for diagnosing hard-to-reach areas. Thus, the areas of mechanical engineering, sanitary and heating construction, and the entire construction industry are among the main applications of the NDT test Instrument.

 

- Camera head diameter: 9 mm / 0.4 in
- Cable length: 1 m / 3.3 ft 
- Interface: Micro USB 2.0
- Memory: Micro SD card
- Front and side view camera

The PCE-830 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

PCE-CT 27FN is a Thickness Test Instrument that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications.

 

- Measuring range of 0 ... 1250 µm / 0 ... 50 mils
- Accuracy of ±(2 % + 2 µm) / ±(2 % + 0.1 mils)
- Features a resolution of 0.1 µ / 0.1 mils

The PCE-CT 28 Thickness Gauge for cars is for measuring the thickness of paint and plastic on ferrous or non-ferrous metals without damaging the coating's surface. The Thickness Gauge stands out due to its high range of measurement.

- Measurement range: 0 ... 1250 µm / 49.2 mils
- Resolution: 0.1 µm / 0.004 mils (in a range of 0.0 µm ... 99.9 µm / 3.9
  mils) 1 µm / 0.04 mils (above the range)
- Accuracy: ± 2% or 2.5 µm / 0.1 mils (highest reading is valid)
- Display: LCD with 4 mm x 10 mm (0.2 in x 0.4 in) high digits

 

Force test stand
The motorised force test stand can be used for vertical tensile and compressive force tests. All force gauges from PCE Instruments can be mounted on the force test stand (if necessary with an adapter plate). The force test stand can withstand a maximum load of 500 N.

- Force range: max. 500 N / 50 kg / 110 lb
- Travel path: max. 270 mm / 10.6"
- Feed speed: 1 ... 500 mm/min
- Manual or automatic procedure

Force gauge
Digital force gauge for tensile force measurement and compressive force measurement up to 500 N. The digital force gauge is for precise measurements with a resolution of 0.1 N.

- Measuring range: 0 ... 500 N
- Accuracy: ± 0.1% of the measuring range
- Tensile and compressive force measurement
- 1600 Hz sampling rate
- Interface: USB
- 6 different measuring tips
- Memory for 100 measurements
- 220V AC ONLY

The PCE-830-3 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The surface testing - inspection camera has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this surface testing - inspection camera. The camera head of this inspection camera can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The Test Stand measures both tensile forces and compressive forces and this with a very high resolution. The tensile force and the compressive force are often determined in the test laboratory, e.g. to determine the yield point, the tear-off force, the force required to operate a button or switch. The supplied motorized test stand can be coupled and operated in various versions with our Test Stands.

Dynamometer PCE-DFG N 5K
- Measuring range: 0 ... 5000 N / 500 kg / 1100 lbs
- Resolution: 1N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

Test Stand PCE-MTS500
- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel path: max. 300 mm / 11.8"
- Feed speed: 30 mm/min ... 230 mm/min / 1.18 ... 9.05 in/min

The PCE-DDM 10 Force Gauge is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 10 Force Gauge is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 10,000 kg / 100 kN / 22,046 lbs
- Resolution: 5 kg / 50 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² or 1450 ... 8702 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

- Measuring range: 10 Nm 7.4 ft-lb
- Resolution: 0.005 Nm / 0.0037 ft-lb
- Accuracy: 0.3% of the measuring range
- USB interface for software connection
- Integrated printer

PCE-HT-225A is a heavy-duty roll hardness tester or concrete test hammer, also called a paper roll rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with rolled paper, concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² or 1450 ... 8702 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

- Measuring range: 1.20 ... 300.0 mm  / 0.04 ... 11.81"
- Accuracy: ±0.5% of measured value + 0.05 mm
- Memory capacity: 1500 measured values
- Calibration reference on housing
- Probe temperature range: -10 ... 60 °C / 14 ... 140 °F

PCE-PST 1 Test Stand and Device for Peel Tests is designed to check the adhesive force of edges and edge bands on support materials. With the Test Stand and Device for Peel Tests, checks can be made with respect to the quality of workmanship. Feed speed, travel distance, tension, and traction angle are fixed. Ball transfer units on the guide surface of the Test Stand reduce the coefficient of friction. Likewise the self-locking jaws and smooth guide rollers always guarantee reproducible and comparable results.

- Measuring range: 500 N / 50 kg / 110 lbs
- Measurable edge thickness: 0.4 mm ... 3.5 mm
- Measurable thicknesses: 10 mm ... 64 mm
- Velocity: 0.3 m / min