With this snake camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the snake camera consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this car measuring device, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the car measuring device consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

PCE-HT 225E is a roll hardness test hammer, also called a rolled paper rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with rolled paper, concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² / 1450.38 ... 8702.26 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- Data processing software included

 

The process indicator can process several different input signals, such as 0...410/4010 Ohm, -10...+63 mV DC, -13...+13 V DC, -24...+24 mA DC or signals from thermocouples and resistance thermometers. This makes the process indicator applicable in a wide range of applications. The measured values are shown on the large LED display of the process indicator.

- 21-point scaling
- IP 65 protection on the front
- Three-colored display
- Two alarm outputs

The NDT test instrument PCE-VE 355N3 is a two-way articulating videoscope, inspection camera, industrial endoscope or borescope for the non-destructive inspection (NDI) of small components and hard-to-reach places. The camera head features 5 LED lights with automatic illumination. Pictures and videos are saved to the included 8 GB SD card memory, allowing easy transfer to a PC.

- 2-way camera probe
- Diameter camera head: Ø 4.5mm / 0.18"
- Interface: Mini-USB 1.1 und AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m /  9ft 10"

PCE-VC21 is a vibration calibrator used to calibrate vibration sensors, meters, analyzers and testers. Suitable for calibrating equipment weighing up to 600 g (1.32 lb), this rechargeable-battery-powered vibration calibrator generates mechanical vibrations with adjustable quartz-stabilized vibration frequencies between 15.92 and 1280 Hz and adjustable vibration amplitudes between 1 m/s² and 20 m/s².

- Load-independent vibration magnitude
- 7 adjustable vibration frequencies
- 5 adjustable vibration amplitudes

 

With this condition monitoring industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this inspection camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the inspection camera consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this automotive tester, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the automotive tester consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this car measuring device, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the car measuring device consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this snake camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the snake camera consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this condition monitoring industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the condition monitoring industrial borescope consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- Up to 1000 V terminal voltage
- Low Ohm measurement
- Direct connection for wallboxes
- Adapter with charging plugs type 1 and type 2
- PE conductor test
- Integrated Schuko socket

The industrial borescope has a 1.5 m / 4.9 ft long endoscope cable. With a diameter of only 4 mm, cavities with the smallest access can be viewed with the help of this industrial borescope. The camera head of this industrial borescope can move freely in 4 directions.

- Cable / head diameter: 4 mm
- Direction of movement camera head: 4-way
- Camera head length: 18 mm
- Bending radius: 8 mm
- 1.5 m / 4.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP67 camera cable
- 1,000,000 pixel image resolution

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

With this industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The color meter PCE-CSM 3 was developed for quality control and offers a very high accuracy reading. When using the color meter, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with these color test instruments, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the 100 reference value easily.