The 4-channel PCE-VM 5000 Vibration Analyzer performs vibration measurements on up to 4 places at the same time. The vibration velocity, acceleration, and displacement in a frequency range of 10 Hz to 1 kHz can be measured. The cables of the vibration sensors are 1.2 m / 3.9 ft long, so the vibration measuring device is able to record vibrations at different points of the component to be tested.

- Frequency range: 10 Hz ... 1 kHz
- Measurement of acceleration, velocity and displacement
- Connection of up to 4 sensors simultaneously, 2 included
- Data storage on SD card

 

The wood moisture meter PCE-MA 100 allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the wood moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time

The absolute moisture meter PCE-MA 100 allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the absolute moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time

The vibration analyzer has a measuring range of 0 ... 200 m/s² for acceleration. In addition to acceleration, the vibration analyzer can also perform speed, displacement, frequency and an ISO 18016-3 measurement.

- Acceleration
- Velocity
- Displacement
- Frequency
- Tachometer    
- Infrared temperature measurement   
- 4 GB data memory
- FFT analysis and wave view of the vibration
- incl. ISO Calibration Certificate

The PCE-830 Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

The Moisture Meter PCE-MA 200 is used to weigh a range of substances up to 200g / 7.05oz and measure their moisture content. A halogen lamp heats up the chamber to 199 °C / 390 °F. The Moisture Meter dries the substance to be weighed within the heating chamber and determines the moisture content from the difference in weight.

- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time
- Accuracy to 0.01 %
- incl. ISO Calibration Certificate

The concrete moisture meter is designed for mobile use by technicians and assemblers. It not only measures the absolute moisture in construction materials or wood, but can also display data regarding air humidity and temperature.

- Easy handling
- Self-test of universal moisture meter
- Wood, board paper and construction material  
- Battery display
- Wet-dry-indicator
- Temperature unit eligible between °C and °F
- Resistive Measuring 

PCE-WP24 is a moisture tester or meter for wood used to perform noninvasive, nondestructive moisture measurements of wood, timber and other construction or building materials. An ideal tool for assessing everything from lumber to floors and more, this moisture meter uses electromagnetic waves that penetrate approximately 50 mm / 1.96 inches to 60 mm / 2.36 inches deep (depending on substrate) to return a mean-value moisture content percentage.

- Moisture content measuring range: 4% ... 60% wood, 0% ... 10% building
  materials
- Resolution: 0.1%
- Accuracy: ±0.7%

The PCE-830-3 Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Vibration acceleration: 0 ... 200 m/s², RMS and peak-peak
- Vibration speed: 0 ... 200 mm/s, RMS
- Vibration distance: 0 ... 2000 μm, peak-peak
- Real-time FFT analysis
- Direct evaluation according to DIN ISO 10816

PCE-MA 110 is an absolute moisture meter or halogen moisture analyzer that functions on the gravimetric or loss on drying (LOD) principle. The absolute moisture meter uses the halogen method to dry the material sample. Moisture content is calculated based on the weight difference before and after the drying procedure. Calibration of the absolute moisture meter can be performed at any time using the automatic calibration function and the included 100 g weight.

- Weighing range: 0.01 g ... 110 g / 0.0035 ... 3.88 oz
- Weighing resolution or readability: 0.1 g / 10 mg
- Moisture content measuring range: 0 ... 100%
- Moisture content resolution or readability: 0.1%
- Adjustable drying time and temperature
- Memory stores up to 16 drying profiles

- Dew point, H2O, temperature, humidity measurement
- Data memory for approx. 50,000 measurement data
- CSV data export
- With G1 / 2" connection thread
- For inline measurement of pressure pipes
- Sensor protected with a cap
- Left connection has NO function
- incl. ISO Calibration Certificate for humidity and temperature

The Moisture Tester for wood is designed for professional use in the control output of sawmills in the input or control of pellet mills, manufacturers of heating briquettes and other branches of production. The Moisture Tester for wood determines the absolute moisture of sawdust and other types of biomass, such as Wood shavings, hay, straw.

- Fast moisture control
- Electrical resistance method
- For biomasses such as straw, hay, sawdust, etc.
- Sample size up to approx. 120 cm³

 

The moisture meter PCE-MA 100-ICA allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time
- incl. ISO Calibration Certificate

PCE-MA 110 is a halogen moisture meter or analyzer that functions on the gravimetric or loss on drying (LOD) principle. The moisture analyzer uses the halogen method to dry the material sample. Moisture content is calculated based on the weight difference before and after the drying procedure. Calibration of the moisture analyzer can be performed at any time using the automatic calibration function and the included 100 g weight.

- Weighing range: 0.1 g ... 110 g / 0.0035 ... 3.88 oz
- Weighing resolution or readability: 0.01 g / 10 mg
- Moisture content measuring range: 0 ... 100%
- Moisture content resolution or readability: 0.1%
- Adjustable drying time and temperature
- Memory stores up to 16 drying profiles
- RS-232 interface or port
- Incl. ISO calibration certificate