For industrial continuous production of concrete, powders, wood, and other small aggregates when in-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 210 moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.
- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: +5 ... +80 °C (+41 ... +176 °F)
- Questionnaire starts evaluation process
The PCE-830-2 Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Analyzer also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.
- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)
Suitable for determining the humidity of bulk substances, this in-process moisture meter for bulk materials can be fitted into containers and systems such as troughs, bunkers, distributors, augers, conveyors, bins and silos. This permits 24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, pastes, seed, or similar bulk or flowing substances.
- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C (+41 ... +176 °F)
- Analog and digital signal output
VHF-Band Moisture sensor Crushed soil, sand, stone, Gravel, Ore. The device is resistant to corrosion (stainless steel and dielectric materials) and can operate in the conditions deviating from the norm, for example, at temperatures of 250 °C. The moisture sensor probe can be mounted on the walls in the hoppers, in pipelines or on trays in conveyors. Due to pluggable design this version of the moisture sensor can also be used for soil moisture control.
- Measurement range: 0 ... 100 %
- Limits of error: <0.5% below 10% moisture
- Range of working temperatures:
0 ... +90 °C (industrial version)
0 ... +115 °C (extended temperature range)
0 ... +250 °C (drying kilns)
The FMD 6 is a handy and versatile moisture tester for wood for reliable measurement of the moisture content of paper, wood and construction materials. The moisture tester for wood has preset characteristic curves for the moisture measurement of specific materials. The moisture tester needs external sensors (sold separately - please see accessory list) to operate. The sensors can be positioned on the surface of a material or inserted into a material, thereby permitting either non-destructive or destructive measurement.
- Measuring range: 5-99% for wood / 0-99% for building materials
- Resolution: 0.1%
- Accuracy: ±0.2%
- Memory stores up to 1,000 measurement values for transfer to PC using
included software
The hay moisture analyzer PCE-HMM is a professional device to designed to determine moisture and temperature of pressed hay and straw. The hay moisture analyzer features a sensor made of stainless steel, which can be purchased in four different lengths, while the wooden handle has an ergonomic design. The hay moisture analyzer proves to be extremely robust, designed to withstand applications for many years.
- Measuring lance: 50 cm
- Measuring range moisture: 9 ... 50%
- Measuring range temperature:
-10 ... 100°C / 14 ... 212°F
- Resolution of display: 0.1%
- Accuracy: 0.8%
The FMD 6 is a handy and versatile wood moisture meter for reliable measurement of the moisture content of paper, wood and construction materials. The wood moisture meter has preset characteristic curves for the moisture measurement of specific materials. The moisture meter needs external sensors (sold separately - please see accessory list) to operate. The sensors can be positioned on the surface of a material or inserted into a material, thereby permitting either non-destructive or destructive measurement.
- Measuring range: 5-99% for wood / 0-99% for building materials
- Resolution: 0.1%
- Accuracy: ±0.2%
- Memory stores up to 1,000 measurement values for transfer to PC using
included software
The moisture sensor is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture sensor is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).
- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C
The PCE-MA 202 is an oven-drying moisture analyzing balance for weighing and heating material samples to determine moisture content. The heating chamber warms up to 199 °C / 390 °F with the use of halogen lamps. Drying of the sample to be weighed takes place within the chamber of the moisture analyzing balance and the moisture content is subsequently calculated from the difference between the initial and final weight.
- Testing or weighing sample capacity: 200 g / 7.05 oz
- Moisture content measurement range: 0 ... 100 %
- Readout, readability or resolution: 10 mg / 0.01 g / 0.1 %
- Adjustable drying temperature and time
- Memory for up to 15 drying programs
The Moisture Tester for wood is designed for professional use in the control output of sawmills in the input or control of pellet mills, manufacturers of heating briquettes and other branches of production. The Moisture Tester for wood determines the absolute moisture of sawdust and other types of biomass, such as Wood shavings, hay, straw.
- Fast moisture control
- Electrical resistance method
- For biomasses such as straw, hay, sawdust, etc.
- Sample size up to approx. 120 cm³
Designed specifically for use in humidity measurement of bulk materials, this humidity sensor is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.
The moisture meter is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture meter is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).
- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction)
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C
The PCE-MA 202 is an oven-drying wood moisture meter for weighing and heating material samples to determine moisture content. The heating chamber warms up to 199 °C / 390 °F with the use of halogen lamps. Drying of the sample to be weighed takes place within the chamber of the wood moisture meter and the moisture content is subsequently calculated from the difference between the initial and final weight.
- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 10 mg / 0.01 g / 0.1%
- Adjustable drying temperature and time
PCE-MA 110 is a wood moisture meter or halogen moisture analyzer that functions on the gravimetric or loss on drying (LOD) principle. The moisture analyzer uses the halogen method to dry the material sample. Moisture content is calculated based on the weight difference before and after the drying procedure. Calibration of the moisture analyzer can be performed at any time using the automatic calibration function and the included 100 g weight.
- Weighing range: 0.01 g ... 110 g / 0.0035 ... 3.88 oz
- Weighing resolution or readability: 0.1 g / 10 mg
- Moisture content measuring range: 0 ... 100%
- Moisture content resolution or readability: 0.1%
- Adjustable drying time and temperature
- Memory stores up to 16 drying profiles
The Moisture Analyzer FMW-B determines moisture content by means of the capacitive method. With the Moisture Analyzer an electromagnetic field quickly determines capacitance of wood. This moisture analyzer is very easy to use as well as very robust.
- Measurement range: 2 ... 30 % H2O wood / 0 ... 60 % building materials
- Resolution: 0.1 %
- Accuracy: ±0.5 % of the reference material
- Memory: 50 measurement values
- Lower frontal sensor
- Non-destructive measurement