- Over 100 combinations pre-selected
- Converts analogue input range
- Completely galvanic isolation
- Power supply 18 ... 265V AC / DC

The process indicator is used for the signal processing of 4 .. 20 mA. The process indicator has a 5-digit LED display to allow the user to read the directly measured current values.

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: 0/4 ... 20 mA, 0 ... 60 mV, ±60 mV DC, 0 ... 10 V, ± 10 V DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

The PCE-N20U is a power indicator used for signal processing. Designed for quick and easy system integration, the digital power indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The power indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

PCE-N20U is a frequency indicator used for signal processing. Designed for quick and easy system integration, the digital panel meter features a large 5-digit LED display with tricolor coding dependent on the measured values. The PCE-N20U also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The PCE-N20U is a panel indicator used for signal processing. Designed for quick and easy system integration, the digital panel indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The panel indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

The PCE-N20U is a pressure indicator used for signal processing. Designed for quick and easy system integration, the digital pressure indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The pressure indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

The PCE-N20U is a voltage indicator used for signal processing. Designed for quick and easy system integration, the digital voltage indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The voltage indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

The PCE-N20U is a digital temperature indicator used for signal processing. Designed for quick and easy system integration, the digital temperature indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The temperature indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers

The digital temperature indicator PCE-N24T is used for processing signals coming from temperature sensors. Depending on your specific needs, the digital indicator can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the digital indicator is freely scalable, which increases its application possibilities.

 

- Power supply: 230 V, 110 V, 24 V, 20 ... 40 V AC/DC, 85 ... 253 V AC/DC (selectable)
- Input signal: PT100, Thermoelement Type J / K (selectable)
- Display: 4 digits, red
- Digit height: 20 mm

The process indicator is used for processing 4...20 mA and 0...20 mA signals. Many measuring transducers and sensors use this type of output, which makes the process indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the process indicator.

- Input (selectable): 0...20 mA, 4...20 mA, ± 20 mA
- Accuracy: ± (0.2 % FS + 1 dgt.)
- Two open collector outputs
- 24 V power supply sytem for sensors and transducers

- Measurement of all relevant environmental parameters
- Wind speed
- Temperature
- Humidity
- Sound level
- Light
- High accuracy
- MIN, MAX, HOLD function

 - Power supply:
   230 V, 110 V, 24 V, 20 ... 40 V AC/DC,
   85 ... 253 V AC/DC (selectable)
- Input signal: ±100 V DC, ±250 V DC,
   ± 400 V DC, 1 A DC, 5 A DC (selectable)
- Display: 4 digits, red
- Digit height: 20 mm / 0.78"

Note: This item must be configured before ordering!

The Current Clamp has been designed to detect, indirectly, AC/DC current and frequency. The Current Clamp has a flashlight integrated to allow for the point of measurement to be illuminated, and a function to test the voltage without contact.

- AC current (50/60 Hz): 200 A / 100-mA / ±3.0% + 8 digits
- DC current:200 A / 0.1 A or 100-mA / ±2.8% + 8 digits
- AC test voltage (without contact):100 VAC to 600 VAC 50 /
  60 Hz
- Frequency: 40 to 50 Hz / 51 to 510 Hz/ 0.51 to 1 kHz

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

PCE-HT 225E is a roll hardness test hammer, also called a rolled paper rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with rolled paper, concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² / 1450.38 ... 8702.26 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- Data processing software included

 

With this condition monitoring industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The PCE-N20U is a process indicator used for signal processing. Designed for quick and easy system integration, the digital process indicator features a large 5-digit LED display with tricolor coding dependent on the measured values. The process indicator also can output signals via two open collector outputs when a threshold value is exceeded.

- Input (selectable): 0...10 V / 0...60 mV / ±10 V
- Accuracy: ± (0.2 % FS + 1 digit)
- 24 V power supply system for sensors and transducers