The PCE-830 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

The current clamp is the ideal measuring device for measuring voltages up to 1500 V AC/DC and currents up to 1000 A AC/DC. The current measurement with the current clamp is inductive. To do this, the supply line is placed in the current clamp.

- Measuring range: 0 ... 1500 V AC/DC
- Free app for Android and iOS
- Data logging for up to 100,000 measured values
- Inrush current measurement
- Insulation categories: CAT IV 600 V, CAT III 1000 V, CAT II 1500 V
- incl. ISO Calibration Certificate

The PCE-830-3 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Simultaneous simulation and measurement mode
- For mA, mV and V
- Graphic display
- Supply of sensors possible
- Manual mode & ramp function
- Continuity test
- Data logger function

The current clamp PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the current clamp, or you can use the integrated clamp mechanism. By using the clamp of the digital current clamp, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism
- Incl. ISO Calibration Certificate

The current clamp PCE-DC 50-ICA is a measuring device for measuring currents of up to 1000 A AC / DC. In addition to current measurement, the current clamp can also measure and test voltage, frequency, duty cycle, resistance, continuity test, capacitors and diodes.

- Current measurement up to 1000 A
- Cover of the measuring sockets
- Voltage measurement up to 600V
- Temperature measurement via 2 thermocouples
- Bluetooth interface
- incl. ISO Calibration Certificate

- Incl. ISO Calibration Certificate

- Measurable electrical parameters: AC V, AC A, resistance
- Clamp diameter: 30 mm
- Operating temperature: -10 ... 50°C / 50 ... 122°F
- Current consumption: 10-mA
- Incl. ISO calibration certificate

- Measuring range up to 3000 A AC
- LC display
- Inrush function
- Frequency measurement
- Data memory
- Incl. ISO Calibration Certificate

The AC/DC current clamp is a versatile measuring instrument for the determination of currents, voltages and many other electrical quantities. With a current clamp opening of 40 mm / 1.6 in, even cables with a larger diameter can be tested with the AC/DC current clamp.

Measurement functions
- DC current
- AC current
- DC voltage
- AC voltage
- Resistance
- Frequency (direct)
- Frequency (current clamp)
- incl. ISO Calibration Certificate

- Simultaneous simulation and measurement mode
- For mA, mV and V
- Graphic display
- Supply of sensors possible
- Manual mode & ramp function
- Continuity test
- Data logger function

This current clamp was developed for the indirect measurement of AC/DC currents as well as the frequency. A non-contact voltage tester function and a torch/flashlight for illuminating the measuring point have also been integrated into this current clamp.

- AC/DC current, AC voltage and frequency measurement
- AC voltage test (contactless test):
   100 VAC to 600 VAC 50/60Hz 100 VAC to 600 VAC 50/60Hz
- DCA zero point function
- Incl. ISO Calibration Certificate

The current clamp is the ideal measuring device for measuring voltages up to 1500 V AC/DC and currents up to 1000 A AC/DC. The current measurement with the current clamp is inductive. To do this, the supply line is placed in the current clamp.

- Measuring range: 0 ... 1500 V AC/DC
- Free app for Android and iOS
- Data logging for up to 100,000 measured values
- Inrush current measurement
- Insulation categories: CAT IV 600 V, CAT III 1000 V, CAT II 1500 V

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission
- Incl. ISO Calibration Certificate

Current clamp for measuring AC/DC current, AC voltage and resistance. This current clamp is designed to indirectly detect AC/DC current and ohms. The current clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The current clamp comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in
- Incl. ISO Calibration Certificate

- Digital Multimeters up to 200 A
- Compact dimensions
- Robust plastic housing
- Multimeter functions
- Safety conditions: IEC1010-1 (2001)
                             CAT II 1000V
                             CAT III 600V
- Incl. ISO Calibration Certificate