The PCE-830 3-Phase Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter / 3-Phase Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-TG 300-P5EE is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: P-E: 2 ... 600 mm / 0.07 ... 23.62", E-E: 2.5 ... 100 mm / 0.09 ...3.93"
- Diameter: 10mm / 0.39"
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).

PCE-VE 370HR3 is a four-way articulating industrial borescope / inspection camera for the non-destructive inspection (NDI) of hard-to-reach places. The waterproof borescope camera head features 5 LED lights (3 front, 2 side) for optimal illumination. In addition, digital image magnification or zoom of up to 2 times is available, plus boost functionality for improved image quality in the dark.

- With boost function: better images in dark surroundings
- 2 additional side LEDs for better lighting
- Diameter: Ø 6 mm / 0.24"
- 4-way camera
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m / 9ft 10"

The PCE-830-3 Portable Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This Portable Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The PCE-TG 300-HT5 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 12mm / 0.47"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

Function:
- Current simulation (active)
- Current simulation (passive)
- Voltage transmitter f. current loop
- Voltage measurement
- Current measurement

The PCE-830-3 3-Phase Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter / 3-Phase Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

Measurement functions
- DC power
- AC power
- DC voltage
- AC voltage
- Resistance
- Frequency (direct)
- Frequency (current clamp)

The two-way optics is a great advantage of the PCE-VE 1034N-F NDT test instrument or inspection camera. There is easy control of the camera head with the NDT test instrument. The NDT test instrument allows you to capture images and videos, and the videos are also stored with an audio recording. 

- Cable length: 3 m / 9.84 ft
- Camera head: 2 way
- Diameter: 4.5 mm / 0.18 in
- Resolution: 640 x 480 Pixel
- Storage of pictures and videos
- 8 GB memory card incl.
- LED lighting

- Sound pressure level: 94 dB, 114 dB
- Accuracy class: IEC 942, class 1
- Accuracy sound level: ± 0.3 dB (20°C / 68°C, 760 mm / 30 in Hg)
- Frequency: 1000 Hz for A, B, C and D frequency weighting
- incl. ISO Calibration Certificate

The Class 1 IoT meter can be used, e.g., for sound measurement of street noise, aircraft and train noise, event noise, noise coming from construction sites, ports, factories involving heavy machinery, airport/bus stations, stadiums, horse/motor racing tracks etc. The weather conditions do not matter, and hail, snow, rain and similar are no problem for this system for outdoor noise monitoring. The IoT meter is equipped with a GPS receiver which allows the user to assign the measured values to an exact position.

 

- Accuracy class 1
- GPS function
- A, B, C & Z frequency rating
- Fast, Slow, Pulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- Incl. Outdoor Alarm Noise Meter Kit PCE-4xx-EKIT
- Outdoor measurement of sound and noise
- Incl. ISO calibration certificate

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

- Borescope camera cable length: 2 m / 6.5 ft
- Cable diameter: 6mm / 0.23"
- Direction of view of the camera frontal
- Camera resolution 1 million pixels
- Camera viewing angle 120°
- Focusing distance 10 … 100 mm / 0.39 … 3.9"
- Flexible camera head length 60 mm / 2.3"
- Radius at 90° bend 50 mm / 1.9"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The PCE-TG 300-NO2 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 3.0 … 300.0 mm / 0.118 ... 11.81" (steel)
- Diameter: 14 mm / 0.55"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 2.5 MHz
- Bluetooth
- incl. ISO calibration certificate

The PCE-TG 300-NO7 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth
- incl. ISO calibration certificate

- incl. ISO-Calibration Certificate