The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-VE 355N is a two-way articulating car measuring device, inspection camera, industrial endoscope or videoscope for the non-destructive inspection (NDI) of small components and hard-to-reach places. The camera head features 5 LED lights with automatic illumination. Pictures and videos are saved to the included 8 GB SD card memory, allowing easy transfer to a PC.

- 2-way camera probe
- Diameter camera head: Ø 4.5mm / 0.18"
- Interface: Mini-USB 1.1 und AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 1.5 m / 4ft 11"

With this condition monitoring industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The PCE-VE 200SV1 automotive tester is a nondestructive inspection camera. Thus, the PCE-VE 200SV1 automotive tester is the ideal instrument for diagnosing hard-to-reach areas. Thus, the areas of mechanical engineering, sanitary and heating construction, and the entire construction and construction industry are among the main applications of the automotive tester PCE-VE 200SV1.

- Camera head diameter 9 mm / 0.4 in
- Cable length: 1 m / 3.3 ft 
- Interface: Micro USB 2.0
- Memory: Micro SD card
- Front and side view camera

PCE-VE 340N is an automotive tester, borescope, inspection camera or industrial endoscope for the non-destructive inspection (NDI) of engines, machines and more. This industrial borescope is an ideal tool for diagnosing issues in hard-to-reach places. The waterproof camera head features 4 LED lights with automatic illumination. In addition, digital image magnification or zoom of up to 2 times is available.

- Diameter camera head: Ø 5.5mm / 0.22"
- Interface: Mini-USB 1.1 and AV out
- Memory: 8 GB SD memory card (incl.)
- Cable length: 10 m / 32 ft 9"

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

With this inspection camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the inspection camera consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Wall Mount Particle Counter
- 6 channel measuring range 0.5(fixed) 0.6-25 um(user defined)
- 45,000 record internal memory
- Counting efficiency: 50% at 0.5 μm 100% at > 0.75 μm according to JIS 
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration mode (PM 2.5, PM 10)
- Ethernet, USB, Touch Screen display, Audible Alarms & Wifi Optional
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921
- Made in the USA

The original BIA class 1 closing force measuring device is an electronic closing force measuring device for rail vehicle and bus doors and sliding steps. The elaborate design combines precision with practical robustness and ensures accurate measured values even after years of use in harsh environments.

- Measuring range: 25 ... 310 N
- Stiffness: 10 N/mm
- Accuracy: +/- 3N or 3% of reading
- Memory for 100 measurements
- Sensor and PC interface
- Applicable standards: EN 14752:2005, VDV 111, VDV 157, 2001/85/EG
- incl. evaluation software PinchPilot
- incl. display unit SEB2
- incl. ISO calibration certificate

PCE-VE 350HR3 is a two-way articulating car measuring device for engine and turbine inspection, and for the non-destructive inspection (NDI) of other hard-to-reach places. The waterproof camera head of this type of car measuring device features 6 LED lights (4 front, 2 side) for optimal illumination. In addition, digital image magnification or zoom of up to 2 times is available, plus boost functionality for improved image quality in the dark.

- With boost function: better images in dark surroundings
- 2 additional side LEDs for better lighting
- Image rotation possible
- Diameter: Ø 6 mm / 0.24"
- 2-way camera
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m / 9ft 10"

With this snake camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the snake camera consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The simple design and an absolutely straightforward operation make it possible for the practitioner to use the adhesion tester as an instrument for daily adhesion tests. Using adhesive with rapid curing, the tests can be performed by the user in the shortest possible time.

- Breakout force: 200 kg
- Diameter of base dolly, mm: 15.1 (№ 1) and 19.5 (№ 2)
- Specific breakout force, MPa: Dolly №1 up to 10 MPa (100) Dolly
  №2 up to 6 MPa (60)

 

- Interference currents, interference voltages, frequencies
- Direct and indirect resistance measurement
- Data memory for later analysis on the PC
- Mobile use thanks to battery and batteries

The closing force transducer is an electronic closing force measuring device for power-operated windows in the motor vehicle sector. Typical areas of application are testing and production in the automotive industry.

- Measuring range: 0 ... 150 N
- Spring stiffness: 10 N/mm
- Accuracy: +/- 3N (0-100N) or +/- 3% (>100N)
- Memory for 100 measurements
- Cable length: 1.5 m / 4.9 ft
- Lithium polymer battery
- Support of relevant standards - 2000/4 EG
- incl. ISO calibration certificate

The original BIA class 1 closing force measuring device is an electronic closing force measuring device for rail vehicle and bus doors and sliding steps. The elaborate design combines precision with practical robustness and ensures accurate measured values even after years of use in harsh environments.

- Measuring range: 25 ... 310 N
- Stiffness: 10 N/mm
- Accuracy: +/- 3N or 3% of reading
- Memory for 100 measurements
- Sensor and PC interface
- Applicable standards: EN 14752:2005, VDV 111, VDV 157, 2001/85/EG
- incl. evaluation software PinchPilot
- incl. display unit SEB2
- incl. ISO calibration certificate

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission