- incl. ISO-Calibration Certificate

With this snake camera, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the snake camera consists of braided tungsten.

- Diameter: Ø2.8mm / 0.11"
- Cable length: 2m / 6.5 ft
- Camera direction: 0°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

The tension dynamometer measures both tensile forces and compressive forces and this with a very high resolution. The tensile force and the compressive force are often determined in the test laboratory, e.g. to determine the yield point, the tear-off force, the force required to operate a button or switch. The supplied motorized test stand can be coupled and operated in various versions with our force gauges.

Force Gauge PCE-DFG N 5K
- Measuring range: 0 ... 5000 N / 500 kg / 1100 lbs
- Resolution: 1N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

Test Stand PCE-MTS500
- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel path: max. 300 mm / 11.8"
- Feed speed: 30 mm/min ... 230 mm/min / 1.18 ... 9.05 in/min

The tension dynamometer is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the tension dynamometer. Despite the high measuring capacity, these materials enable a compact design with a low weight.

- Measurement range: 5,000 kg / 50 kN / 11,023 lb
- Resolution: 2 kg / 20 N
- Minimum load: 40 kg / 88 lbs
- Supplied with remote control indicator

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

- Measurement according to UCI method
- Testing of HRC, HRB, HV, HB, MPa
- Measuring direction 360 °
- Large LCD
- USB interface
- Incl. 50 N / 11.2 lbs UCI probe

With this condition monitoring industrial borescope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the industrial borescope consists of braided tungsten.

- Diameter: Ø2.8mm / 0.11"
- Cable length: 2m / 6.5 ft
- Camera direction: 0°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- incl. ISO-Calibration Certificate

- Measures Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc in both Metric (µm) and Imperial (µinch)
- Ra, Rq, Rc : 0.005 μm…16 μm / 0.197 µinch ... 629.921 µinch measurement range
- Rz, Rt Rp, Rv: 0.020 µm … 200 µm / 0.797 µinch ... 7874.016 µinch measurement range
- Rsm: 5 μm …1000 μm / 1968 µinch … 3937 µinch measurement range
- Rsk: -1 …. 1 measurement range
- Measurement accuracy: <± 10% and Repeatability < 6%
- Robust Piezoelectric sensor
- Saves up to 20 Data points
- 3 different cutoff wavelengths
- Micro USB Interface
- PC Software
- Built-in rechargeable li-ion battery

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.2 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
- Incl. ISO calibration certificate

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

 

The portable and easy-to-use roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

The surface tester PCE-RT 2000BT is used for accurate measurement of surface roughness. The surface tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via wifi and USB
- Two different probes for NFe and Fe (included)

- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces 

The roughness tester PCE-RT 2000BT is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store