The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

- Camera head diameter: 60 mm / 2.4 in
- Cable length: 120 m / 393.7 ft
- Pipe diameter from & to: 80 ... 1200 mm / 3.1 ... 47.2 in
- Field of view: 20 ... 100 cm
- SD card up to 256 GB
- ø9.5 mm fiber optic cable
- Motorized camera
- With cable trolley

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

The force gauge / belt tension meter is an optical measuring instrument for determining the belt tension force. This force measuring device consists of a display unit and a sensor on a gooseneck cable. The force gauge measures the tension of the belt in a stationary state.

- Measures the oscillation frequency of the belt
- Measuring range: 10 ... 900 Hz
- Accuracy: ± (1% of rdg. + 4 digits)
- Resolution: <100 Hz: 0.1 Hz
                       >100 Hz: 1 Hz
- Memory for 750 measured values
- Length of gooseneck sensor 25 cm / 9,8 in

- Melting rate: 0.1 to 400.0 g / 10 min
- Heating temperature: 120 ... 400°C / 248 ... 752°F
- Measuring accuracy temperature: ± 0.2°C / 0.36°F
- Resolution: 0.1°C / 0.18°F
- Large 7" TFT touch display
- Already pre-set materials
- Various weights included
- Standards: ISO1133-1997, ASTM 1238-04C, GB / T3682-2000

PCE-5000 is a portable material hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

PCE-5000 is a portable material hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

The automotive material thickness tester is used for the quick and precise detection of layer thicknesses on metals. In comparison to many other thickness meters, this automotive material thickness tester does not have to differentiate between ferrous and non-ferrous metal.

The force gauge / belt tension meter is an optical measuring instrument for determining the belt tension force. This force measuring device consists of a display unit and a sensor on a gooseneck cable. The force gauge measures the tension of the belt in a stationary state.

- Measures the oscillation frequency of the belt
- Measuring range: 10 ... 900 Hz
- Accuracy: ± (1% of rdg. + 4 digits)
- Resolution: <100 Hz: 0.1 Hz
                       >100 Hz: 1 Hz
- Memory for 750 measured values
- Length of gooseneck sensor 16 cm

PCE-5000 is a portable hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

PCE-VE 200-S3 is an industrial inspection camera, endoscope or borescope for the non-destructive evaluation (NDE) of engines, machines and more. This industrial borescope provides excellent image quality at an affordable price. An ideal tool for diagnosing issues in hard-to-reach places, the waterproof camera head features 6 LED lights with adjustable intensity for optimal illumination. In addition, digital image magnification or zoom of up to 4 times is available.

- 3.7 mm / 0.14 in diameter
- 3 m / 9.8 ft cable length
- 1600 x 1200 pixels JPEG image / 640 x 480 pixels AVI video