The Anemometer PCE-WSAC 50-311 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 4 ... 20 mA
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-321 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 0 ... 10 V
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-211 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 4 ... 20 mA
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Borescope camera cable length: 2 m / 6.5 ft
- Cable diameter: 6mm / 0.23"
- Direction of view of the camera frontal
- Camera resolution 1 million pixels
- Camera viewing angle 120°
- Focusing distance 10 … 100 mm / 0.39 … 3.9"
- Flexible camera head length 60 mm / 2.3"
- Radius at 90° bend 50 mm / 1.9"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The PCE-WSAC 50-920 anemometer shows the speed of the wind and also the average figure over the prior two minutes and five minutes. The smallest wind motion is detected by this accurate anemometer. The timber industry, the mining industry, and the construction industry are some examples of applicable wind monitoring application areas for the anemometer.

- Pre-alarm and full alarm with visual and audible warnings
- Measuring range: 0 ... 110 mph
- Power supply: 24 V DC
- Signal input: 0...10 V
- incl. ISO calibration certificate

A strong wind is not esssential to use the PCE-WSAC 50-910 anemometer, as it has a measuring range of 0 to 110 mph. In addition to the actual wind speed, this versatile anemometer can display the average wind speed over the last two minutes and five minutes. The anemometer is suitable for numerous wind detection applications in outdoor industries, e.g. on construction sites.

- Pre-alarm and full alarm with visual and audible warnings
- Measuring range: 0 ... 110 mph
- Power supply: 24 V DC
- Signal input: 4...20 mA
- incl. ISO calibration certificate

PCE-PCO 2 is a portable handheld air quality particle counting meter or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also measures air temperature, dew point and relative humidity.

- PM channels: PM 2.5, PM 10, including mass concentration mode (µg/m³)
- Particle sizes (in micrometers): 0.3 µm, 0.5 µm, 1.0 µm, 2.5 µm, 5.0 µm, 10 µm
- Temp. measuring range: 0 ... +50 °C / +32 ... +122 °F
- Humidity measuring range: 0 ... 100 % RH
- Built-in camera for image and video recording
- Free software download on PCE Software web page

This Data Logger meter is very economical. With this Data Logger meter you can measure wind speed and air temperature. These test instruments are calibrated by the manufacturer. An ISO calibration certificate is available as an option.

- Speed measurement up to 45 m/s or 100 mph
- Wind speed: 0.01 m/s, accuracy ±3% ±0.1
- Air temperature: 0.2°C / 32.4°F, accuracy ±1°C / 33.8°F
- Air flow: 0.001 to 100, accuracy calculated from the wind speed and surface

 

PCE-WMM 50 is a wall-mounted air quality meter that uses diffusion to monitor carbon dioxide (CO2) gas levels and ambient temperature (ºC / ºF) indoors. This indoor air quality meter features an alarm-activated potential-free contact that can, for example, activate a fan to reduce CO2 gas concentration in the room.

- CO2 gas measurement range: 0... 50,000 ppm
- Temperature measurement range: 0... +45 ºC / +32... +113 ºF
- IP54-rated enclosure on sensor and remote display units
- 2 adjustable alarm thresholds
- 3- to 4-digit remote display (depends on range)

 

- Measurable particle sizes: PM2.5 / PM10
- Measuring range Mass concentration: 0 ... 2000 μg / m³
- Measurable particle sizes: 0.3, 2.5 and 10 μm
- Display with graphic real-time diagram
- Data memory up to 5000 data sets

The Anemometer PCE-WSAC 50-110 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Supply voltage: 230 V AC
- Input signal: 4 ... 20 mA
- 2 types of alarms
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-120 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 230 V AC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-220 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-310 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 4 ... 20 mA
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-320 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

The Anemometer PCE-WSAC 50-210 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 4 ... 20 mA
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate

Measuring function
- PM2.5
- Humidity
- Temperature
- CO2
- Air pressure
- Memory: SD card max. 32 GB
- Ideal for workplace monitoring
- Alarm function

PCE-WSAC 50 is a weather station that displays the current wind speed as well as the average wind speed of the last 2 and 5 minutes. This weather station allows measurement of the slightest wind movements. PCE-WSAC 50 is used for a variety of wind monitoring applications in industries such as construction, mining, renewable energy and manufacturing.

- Pre-alarm and full alarm with visual and audible warnings
- Optional RS-485 modbus interface for data communication
- Measuring range: 0 ... 50 m/s or 0 ... 110 mph
- Incl. ISO calibration certificate