PCE-WP24 is a damp meter for wood used to perform noninvasive, nondestructive moisture measurements of wood, timber and other construction or building materials. An ideal tool for assessing everything from lumber to floors and more, this moisture meter uses electromagnetic waves that penetrate approximately 50 mm / 1.96 inches to 60 mm / 2.36 inches deep (depending on substrate) to return a mean-value moisture content percentage.

- Moisture content measuring range: 4% ... 60% wood, 0% ... 10% building
  materials
- Resolution: 0.1%
- Accuracy: ±0.7%

 

The moisture analyzer is a sensor for measuring moisture of sand and liquids consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture analyzer is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, and fuels (CWF).

- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 10% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

The Wood Moisture Meter FMW-T covers all your needs while measuring moisture contents in all types of wood and building materials. The Wood Moisture Meter works without causing any damage to the material and it is mainly used to measure building walls.

- Measurement range: 2 ... 30 % H2O wood / 0 ... 60 % building materials
- Resolution: 0.1 %
- ±0.5 % accuracy of reference material
- Memory: 50 measurement values
- Upper frontal sensor
- Non destructive measurement

For industrial continuous production of wood pellets, chips, sawdust and similar materials when in-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 210 moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.

- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: +5 ... +80 °C  (+41 ... +176 °F)
- Questionnaire starts evaluation process

The PCE-WP24 is a environmental meter used to perform noninvasive, nondestructive moisture measurements of wood, timber and other construction or building materials. An ideal tool for assessing everything from lumber to floors and more, this environmental meter uses electromagnetic waves that penetrate approximately 50 mm / 1.96 inches to 60 mm / 2.36 inches deep (depending on substrate) to return a mean-value moisture content percentage.

- Moisture content measuring range: 4% ... 60% wood, 0% ... 10% building
  materials
- Resolution: 0.1%
- Accuracy: ±0.7%

 

The Absolute Moisture Meter is designed for professional use in the control output of sawmills in the input or control of pellet mills, manufacturers of heating briquettes and other branches of production. The Absolute Moisture Meter determines the absolute humidity of sawdust and other types of biomass, such as Wood shavings, hay, straw.

- Fast moisture control
- Electrical resistance methods
- For biomasses such as straw, hay, sawdust, etc.
- Sample size up to approx. 120 cm³

 

The relative humidity meter PCE-MA 100-ICA allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the relative humidity meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time
- incl. ISO Calibration Certificate

PCE-MA 110 is a halogen relative humidity meter or analyzer that functions on the gravimetric or loss on drying (LOD) principle. The relative humidity meter uses the halogen method to dry the material sample. Moisture content is calculated based on the weight difference before and after the drying procedure. Calibration of the relative humidity meter can be performed at any time using the automatic calibration function and the included 100 g weight.

- Weighing range: 0.1 g ... 110 g / 0.0035 ... 3.88 oz
- Weighing resolution or readability: 0.01 g / 10 mg
- Moisture content measuring range: 0 ... 100%
- Moisture content resolution or readability: 0.1%
- Adjustable drying time and temperature
- Memory stores up to 16 drying profiles
- RS-232 interface or port
- Incl. ISO calibration certificate

The relative humidity meter has a moisture measuring range of 0 … 100%. The relative humidity meter is operated via the 5" touchscreen. To determine the moisture content with the relative humidity meter, a sample is evenly distributed on the sample pan.

- Measuring range: 0 ... 110 g / 0 ... 3.88 oz
- Resolution: 0.001 g
- Memory for 32 drying parameters
- 5" touch screen for easy operation
- RS-232 interface for connection to a PC

Suitable for determining the humidity of bulk substances, this moisture test instrument can be fitted into containers and systems such as troughs, bunkers, distributors, augers, conveyors, bins and silos. This permits 24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, pastes, seed, or similar bulk or flowing substances. These test instruments / test sensors are mainly for use in manufacturing processes to give the opportunity of process optimization to the manufacturer or to insure the moisture content of the final product.

- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

Designed specifically for use in moisture measurement of various bulk materials, these moisture analyzing test instruments are installed in bins, silos, troughs, bunkers, distributors, augers, and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

The humidity detector allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the humdity detector dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time