The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.
- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate
PCE-FD 20 is a portable ultrasonic tester or ultrasonic thickness gauge with a large LCD screen that displays A-scan maps of ultrasonic signals as well as B-scan cross sections. Ideal for use in mechanical engineering, aerospace and metallurgical applications, this high-frequency ultrasound-based thickness meter uses a contact transducer (two different probes included; 45° and 90°) to measure material thickness and identify flaws and defects such as discontinuity in welds.
- Operating frequency range: 1 ... 10 MHz
- Measured time interval range: 6 ... 1000 microseconds (µs)
- Sound velocity: 1000 ... 9999 m/s
The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.
- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate
PCE-CT 27FN is a Thickness Gauge that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications.
- Measuring range of 0 ... 1250 µm / 0 ... 50 mils
- Accuracy of ±(2 % + 2 µm) / ±(2 % + 0.1 mils)
- Features a resolution of 0.1 µ / 0.1 mils
- incl. ISO Calibration Certificate
The material thickness meter for cars is for measuring the thickness of paint and plastic on ferrous or non-ferrous materials without damaging the coating's surface. The material thickness meter stands out due to its high range of measurement.
- Measurement range: 0 ... 1250 µm / 49.2 mils
- Resolution: 0.1 µm / 0.004 mils (in a range of 0.0 µm ... 99.9 µm / 3.9 mils)
1 µm / 0.04 mils (above the range)
- Accuracy: ± 2% or 2.5 µm / 0.1 mils (highest reading is valid)
- Display: LCD with 4 mm x 10 mm (0.2 in x 0.4 in) high digits
- Incl. ISO Calibration Certificate
The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).
- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate
- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- Saves up to 20 Data points
- Micro-USB interface
- Built-in rechargeable li-ion battery
- Incl. ISO calibration certificate
PCE-CT 27FN is a material thickness meter that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications.
- Measuring range of 0 ... 1250 µm / 0 ... 50 mils
- Accuracy of ± (2% + 2 µm) / ± (2% + 0.1 mils)
- Features a resolution of 0.1 µ / 0.1 mils
- Incl. ISO Calibration Certificate
PCE-CT 5000H is a thickness measuring instrument used for the rapid determination of coating thicknesses on ferrous (Type F) and non-ferrous (Type N) metals. The Thickness Meter automatically detects the type of metal to be measured.
- Type F measuring range: 0 ... 5000 µm / 0 ... 5 mm / 0 ... 196 mils
- Type N measuring range: 0 ... 3000 µm / 0 ... 3 mm / 0 ... 118 mils
- Displays measuring units in μm, mm or mils
- Saves up to 2000 measurements to internal memory
- Practical V-groove on the measuring head
- Incl. ISO Calibration Certificate
With this automotive tester, layer thicknesses on metallic surfaces can be reliably determined. The automotive tester has a measuring range of 1500 µm. This means that the automotive tester is used, for example, in a paint shop, for incoming goods inspection or for an expert.
- Measuring range up to 1500 µm
- Measurable substrates: Fe, NFe
- Probe: internal
- Micro USB and Bluetooth interface
- Data storage for up to 600 measured values
- incl. ISO Calibration Certificate