The moisture meter PCE-MA 202 allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 10 mg / 0.01 g / 0.1%
- Adjustable drying temperature and time

The moisture sensor is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture sensor is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).

- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +76 °C

PCE-MA 110 is a halogen moisture meter or analyzer that functions on the gravimetric or loss on drying (LOD) principle. The moisture analyzer uses the halogen method to dry the material sample. Moisture content is calculated based on the weight difference before and after the drying procedure. Calibration of the moisture analyzer can be performed at any time using the automatic calibration function and the included 100 g weight.

- Weighing range: 0.1 g ... 110 g / 0.0035 ... 3.88 oz
- Weighing resolution or readability: 0.01 g / 10 mg
- Moisture content measuring range: 0 ... 100%
- Moisture content resolution or readability: 0.1%
- Adjustable drying time and temperature
- Memory stores up to 16 drying profiles
- RS-232 interface or port

The data logger for temperature and humidity is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the data logger for temperature and humidity determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

The dust measuring device is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the dust measuring device determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

The absolute moisture meter has a moisture measuring range of 0 … 100%. The absolute moisture meter is operated via the 5" touchscreen. To determine the moisture content with the absolute moisture meter, a sample is evenly distributed on the sample pan.

- Measuring range: 0 ... 110 g / 0 ... 3.88 oz
- Resolution: 0.001 g
- Memory for 32 drying parameters
- 5" touch screen for easy operation
- RS-232 interface for connection to a PC

The wood moisture meter PCE-MA 100 allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the wood moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time

The absolute moisture meter PCE-MA 100 allows different materials to be weighed and their moisture contents determined. The heating chamber is heated by halogen lamps up to 199 °C. In this chamber, the absolute moisture meter dries the material to be weighed, and then calculates the moisture content from the weight difference.

- Testing or weighing capacity: 110 g / 3.88 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time

Suitable for determining the humidity of bulk substances, this moisture test instrument can be fitted into containers and systems such as troughs, bunkers, distributors, augers, conveyors, bins and silos. This permits 24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, pastes, seed, or similar bulk or flowing substances. These test instruments / test sensors are mainly for use in manufacturing processes to give the opportunity of process optimization to the manufacturer or to insure the moisture content of the final product.

- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

The air sampler is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the air sampler determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

- Measuring range: 0 ... 362.6 psi, 0 ... 25 bar
- Resolution: 0.145 psi, 0.01 bar
- Scaled bar graph
- Measurable media: gases, water
- incl. ISO Calibration Certificate

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.

- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips