The Gas Detector Gasman-CO is a unique gas meter which protects against a specific gas, inflammable or toxic. The Gas Detector warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Gas Detector fulfills all the European and international norms, even ATEX and UL standards.

- Non-rechargeable, 1-year battery
- For CO (Carbon Monoxide)
- Dust and water resistant - IP 65/67
- 0... 500 ppm

 

The gas leak detector has a CO² measuring range of 0 ... 9999 ppm. In addition to the carbon dioxide measurement, the gas leak detector also has a carbon monoxide (CO) sensor with a measuring range of 0 ... 1000 ppm and a temperature and humidity sensor.

- Carbon monoxide (CO): 0 … 1000 ppm
- Carbon dioxide (CO²): 0 … 9999 ppm
- Temperature: 0 … 50 °C / 32 … 122 °F
- Humidity: 0 … 100% RH
- Data memory for 5000 measuring points
- Data export CSV
- Power supply: rechargeable battery

PCE-MMK 1 is a portable digital moisture meter used to measure the moisture content of wood, paper, textiles, concrete and other building materials. This multifunction handheld humidity detector also measures ambient temperature and ambient relative humidity.

Measuring ranges:
- Wood, paper, textiles: 1 ... 75% moisture
- Concrete, building materials: 0.1 ... 2.4% moisture
- Ambient temperature: -40 ... 70°C / -40 ... 158°F
- Ambient relative humidity (RH): 0 ... 100 % RH

The Gas Leak Detector Gasman-CO is a unique gas meter which protects against a specific gas, inflammable or toxic. The Gas Leak Detector warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Gas Leak Detector fulfills all the European and international norms, even ATEX and UL standards.

- Non-rechargeable, 1-year battery
- For CO (Carbon Monoxide)
- Dust and water resistant - IP 65/67
- 0... 500 ppm

 

Designed specifically for use in humidity measurement of bulk materials, this humidity detector is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

- Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

VHF-Band Moisture Meter Crushed Stone, Gravel, Ore (conveyor). The device is resistant to corrosion (stainless steel and dielectric materials) and can operate in the conditions deviating from the norm, for example, at temperatures of 145 °C. The humidity detector probe can be mounted on the walls in the hoppers, in pipelines or on trays in conveyors. Due to pluggable design this version of the humidity detector can also be used for soil moisture control.

- Measurement range: 0 ... 100 %
- Limits of error: <0.5% below 10% moisture
- Range of working temperatures:
  0 ... +90 °C (industrial version)
  0 ... +115 °C (extended temperature range) 
  0 ... +250 °C (drying kilns)

Suitable for determining the humidity of bulk substances, this absolute humidity detector can be fitted into containers and systems such as troughs, bunkers, distributors, augers, conveyors, bins and silos. This permits 24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, pastes, seed, or similar bulk or flowing substances.

- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)

 

- Measuring range up to 10000 ppm
- Audible alarm with 85 dB
- Rechargeable battery for mobile use
- Automatic calibration
- For the detection of combustible gases

PCE-FD 20 is a portable ultrasonic flaw detector with a large LCD screen that displays A-scan maps of ultrasonic signals as well as B-scan cross sections. Ideal for use in mechanical engineering, aerospace and metallurgical applications, this high-frequency ultrasound-based flaw detector uses a contact transducer (two different probes included; 45° and 90°) to measure material thickness and identify flaws and defects such as discontinuity in welds.

- Operating frequency range: 1 ... 10 MHz
- Measured time interval range: 6 ... 1000 microseconds (µs)
- Sound velocity: 1000 ... 9999 m/s 

 

The humidity detector is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our humidity detector is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).

- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The humidity detector of PCE Instruments helps meet those criteria through highly accurate moisture measurement.

- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

With the gas detector you can ensure the right climate in your office. The gas detector measures the CO2 content of the air, the relative humidity and the room temperature. The gas detector shows carbon dioxide concentrations up to 9999 ppm, temperatures from -10… 50 °C, and relative humidity values from 20… 95%.

- Large CO2 measuring range up to 9999 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- Network operation
- Suitable for classrooms, offices, lecture halls

- Up to 15 gases
- For flammable gases
- 500 mm / 19.6" sensor
- Visual, audible and haptic alarm

The Ozone Meter Xgard-1-O3 is a single-gas gas sensor used to warn for gases (Ozone, O₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

- Large CO2 measuring range up to 5000 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- 5 h graph for long-term monitoring
- Battery and power adapter operation
- Suitable for classrooms, nurseries/kindergartens, lecture halls