The gas detector PCE-WMM 100 consists of a main unit and a remote display. The CO2 gas detector is used to measure carbon dioxide and oxygen in a fixed location. The gas detector has two relays that can be used to control alarm lights or sounders.

- Measuring range CO2: 0 .... 50000 ppm
- Measuring range O2: 0 ... 30 %
- Measuring range temperature: 0 ... 50 °C / 32 ... 122 °F
- Main and remote unit
- Alarm relay
- 4 ... 20 mA analog outputs
- Acoustic alarm

With its hydrogen-selective sensor, the leak detector can detect the smallest leaks with a very low leak rate. Containers or lines that do not contain hydrogen can also be checked for leaks with the leak detector if they are filled with test gas containing hydrogen and then checked for leaks.

- High sensitivity: > 2 g / year
- Medium sensitivity: > 15 g / year
- Low sensitivity: > 30 g / year - bar display with traffic light function
- Three adjustable sensitivities
- Semi-rigid probe with a length of 40 cm / 15.7"
- Audible and visual alarm

The Gas Leak Detector Gasman-SO2 is a unique gas meter which protects against a specific gas, inflammable or toxic. The Gas Leak Detector warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Gas Leak Detector fulfills all the European and international norms, even ATEX and UL standards.

- Non-rechargeable, 1-year battery
- For SO₂ (Sulfur Dioxide)
- Dust and water resistant - IP 65/67
- 0... 20 ppm

 

PCE-LD 1 is a portable handheld refrigerant gas leak detector used to locate CFC/HFC refrigerant gas leaks. This highly sensitive gas leak detector can locate gas leaks from HVACR refrigeration systems even in areas contaminated by other gases. The gas sensor is located at the end of a 390 mm / 15.35 in flexible goose-neck tube, allowing unique access to hard-to-reach places.

- Adjustable high / low sensitivity:
    6 g/yr or 30 g/yr for R-22 and R-134a
    8 g/yr or 40 g/yr for R404A, R-407C and R-410A

 

PCE-VOC 1 is a portable handheld volatile organic compound (VOC) and formaldehyde (HCHO) meter or gas leak detector for indoor air quality (IAQ) monitoring applications. This easy-to-use VOC meter is ideal for measuring total volatile organic compound (TVOC) and formaldehyde (HCHO) levels in homes, offices, factories, laboratories, hotels, schools and other indoor environments.

- TVOC range: 0.00... 9.99 ppm
- HCHO range: 0.00... 5.00 ppm
- Displays units in ppm or mg/m³
- Audible and visual alarms
- Long-lasting rechargeable battery

The gas detector has a CO² measuring range of 0 ... 9999 ppm. In addition to the carbon dioxide measurement, the gas detector also has a carbon monoxide (CO) sensor with a measuring range of 0 ... 1000 ppm and a temperature and humidity sensor.

- Carbon monoxide (CO): 0 … 1000 ppm
- Carbon dioxide (CO²): 0 … 9999 ppm
- Temperature: 0 … 50 °C / 32 … 122 °F
- Humidity: 0 … 100% RH
- Data memory for 5000 measuring points
- Data export CSV
- Power supply: rechargeable battery

The TXgard-Plus gas detector is a robust, flame-proof gas sensor for toxic gases or oxygen. The TXgard-Plus gas detector is available in different versions, depending on the gases for which it is to be used. The gas measuring device measures the respective gases with the help of an integrated, electrochemical detector.

- Different versions available
- Flame-proof construction with ATEX approval
- Electrochemical detector
- 3-wire 4 ... 20 mA output

The Xgard-1-SO2 is a single-gas Gas Leak Detector used to warn for gases (Sulfur Dioxide, SO₂, 0 ... 10 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Sulfur Dioxide, SO₂, 0 ... 10 ppm)
- Additional display and alarm station
- ATEX or UL approval

With the gas leak detector you can ensure the right climate in your office. The gas leak detector measures the CO2 content of the air, the relative humidity and the room temperature. The gas leak detector shows carbon dioxide concentrations up to 9999 ppm, temperatures from -10… 50 °C, and relative humidity values from 20… 95%.

- Large CO2 measuring range up to 9999 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- Network operation
- Suitable for classrooms, offices, lecture halls

This gas leak detector is designed as a cost-effective solution for applications where protection against a specific combustible or toxic gas is required. The Gasman gas leak detector is a single gas detector.

- Gas detector for flammable gases
- Range: 0...100%
- Alarm: 20%
- Memory for 5000 events
- Data logger for 900 hours of storage with 1 minute intervals
- Interface for calibrating, configuring and reading out the data
- Weight: 130g / 4.5 oz
- incl. charger

- Measuring range up to 10000 ppm
- Audible alarm with 85 dB
- Rechargeable battery for mobile use
- Automatic calibration
- For the detection of combustible gases

The chlorine gas detector is a highly accurate measuring device for measuring the chlorine concentration in our ambient air. Furthermore, sensor heads for other gases are also available for the chlorine gas detector, which are automatically recognized when they are plugged into the device.

- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- incl. sensor head for chlorine
- Different sensor heads selectable
- Digital output
- Data logger

The Gas Detector AQ-500 Set EF is a high-precision measuring device for measuring the formaldehyde concentration in our circulating air.

- Range Formaldehyde: 0...10 ppm
- High accuracy and functionality
- Digital output: RS232 with USB converter
- Data Logger: 8188 values
- PC transfer: Software and data cable included

Triple Plus+ is the latest generation of the respected "Triple" family of toxic, oxygen and flammable gas detectors. Intrinsically safe, the Triple Plus+ provides enhanced features for safety and detector fleet managers including:

- Selection of flammable gas correction factors (so one unit can be used in
  several locations across a site)
- Annotation of the data file with user names and site names selected from
  pre-configured files in the unit

* Call to order or see accessories tab. Must specify sensors (see chart for details) and choose with / without internal pump. Charger and software sold separately.

 

The Xgard-1-PH3 is a single-gas Gassensor used to warn for gases (Phosphine, PH₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Phosphine, PH₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

The humidity detector provides exceptionally accurate grain moisture measurement in real time. The humidity detector uses low-power microwaves to penetrate the surface every 0.2 second and obtain interior moisture readings without causing any damage. An integrated temperature probe ensures the readings are accurate from 5°C to 55°C / 41°F to 131°F. Suitable for the continuous monitoring of moisture in corn, soybeans, wheat, rice, sorghum, barley, oats, rye, hops, green coffee, cocoa beans, oil seeds, flax seeds, sunflower seeds, poppy seeds, pumpkin seeds, spelt seeds, buckwheat, sesame, peas, fava beans, scarlet runner beans, triticale, amaranth and jatropha.

- Boasts a measurement range of 5% to 40% for moisture content during
  continuous mass flow with an error of just ±0.5% from 5% to 18% grain
  moisture
- Lowers energy costs by enabling shorter drying times and reduces labor costs
  by automating the moisture monitoring process
- Provides nearly maintenance-free operation, delivering consistently accurate
  moisture readings over time
- Analog output of 4 to 20 mA can be converted to digital for dryer control

 

The Xgard-1-H2 is a single-gas Gas detector used to warn for gases (Hydrogen, H₂, 0 ... 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Hydrogen, H₂, 0 ... 2000 ppm)
- Additional display and alarm station
- ATEX or UL approval

The Gas Leak Detector Gasman-O2 is a unique gas meter which protects against a specific gas, inflammable or toxic. The Gas Leak Detector warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Gas Leak Detector fulfills all the European and international norms, even ATEX and UL standards.

- Non-rechargeable, 1-year battery
- For NO₂ (Oxygen)
- Dust and water resistant - IP 65/67
- 0... 25% v/v