The chlorine gas leak detector is a highly accurate measuring device for measuring the chlorine concentration in our ambient air. Furthermore, sensor heads for other gases are also available for the chlorine gas leak detector, which are automatically recognized when they are plugged into the device.

- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- incl. sensor head for chlorine
- Different sensor heads selectable
- Digital output
- Data logger

- Measuring range up to 10000 ppm
- Audible alarm with 85 dB
- Rechargeable battery for mobile use
- Automatic calibration
- For the detection of combustible gases

This Gas Leak Detector is designed to detect formaldehyde in air. The Gas Leak Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The formaldehyde Gas Leak Detector runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Measuring range: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

This gas detector is designed as a cost-effective solution for applications where protection against a specific combustible or toxic gas is required. The Gasman gas detector is a single gas detector.

- Gas detector for flammable gases
- Range: 0...100%
- Alarm: 20%
- Memory for 5000 events
- Data logger for 900 hours of storage with 1 minute intervals
- Interface for calibrating, configuring and reading out the data
- Weight: 130g / 4.5 oz
- incl. charger

Gas Detector AQ-300 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Detector can be equipped with four different heads that vary in their measurement range.

- High accuracy and functionality
- Battery operation
- Alarm function

 

 

The Xgard-1-PH3 is a single-gas Gas Leak Detector used to warn for gases (Phosphine, PH₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Phosphine, PH₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

This gas leak detector is designed as a cost-effective solution for applications where protection against a specific combustible or toxic gas is required. The Gasman gas leak detector is a single gas detector.

- Gas detector for flammable gases
- Range: 0...100%
- Alarm: 20%
- Memory for 5000 events
- Data logger for 900 hours of storage with 1 minute intervals
- Interface for calibrating, configuring and reading out the data
- Weight: 130g / 4.5 oz
- incl. charger

The Xgard-1-H2 is a single-gas Gas detector used to warn for gases (Hydrogen, H₂, 0 ... 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Hydrogen, H₂, 0 ... 2000 ppm)
- Additional display and alarm station
- ATEX or UL approval

Single-Gas Gas Leak Detector warning for gases (for Carbon Dioxide CO₂), / without display / with signal output for sensors in combination with a stationary equipment to detect gases (with ATEX approval).

- Stationary
- For Carbon Dioxide CO₂
- Additional display and alarm station
- ATEX approved

 

The Xgard-1-O3 is a single-gas Gassensor used to warn for gases (Ozone, O₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

The Xgard Type 5 gas detector is a robust, explosion-proof gas sensor for flammable gases. The Xgard Type 5 gas detector is available in different versions, depending on the gases for which it is to be used. The gas measuring device measures the respective flammable gases with the help of an integrated pellistor.
 
- Different versions available
- Explosion-proof construction with ATEX approval
- Detection by pellistor
- 3-wire 4 ... 20 mA output

The humidity detector provides exceptionally accurate grain moisture measurement in real time. The humidity detector uses low-power microwaves to penetrate the surface every 0.2 second and obtain interior moisture readings without causing any damage. An integrated temperature probe ensures the readings are accurate from 5°C to 55°C / 41°F to 131°F. Suitable for the continuous monitoring of moisture in corn, soybeans, wheat, rice, sorghum, barley, oats, rye, hops, green coffee, cocoa beans, oil seeds, flax seeds, sunflower seeds, poppy seeds, pumpkin seeds, spelt seeds, buckwheat, sesame, peas, fava beans, scarlet runner beans, triticale, amaranth and jatropha.

- Boasts a measurement range of 5% to 40% for moisture content during
  continuous mass flow with an error of just ±0.5% from 5% to 18% grain
  moisture
- Lowers energy costs by enabling shorter drying times and reduces labor costs
  by automating the moisture monitoring process
- Provides nearly maintenance-free operation, delivering consistently accurate
  moisture readings over time
- Analog output of 4 to 20 mA can be converted to digital for dryer control

 

The Xgard-1-NH3 is a single-gas Gas detector used to warn for gases (Ammonia, NH₃, 0 ... 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ammonia, NH₃, 0 ... 50 ppm)
- Additional display and alarm station
- ATEX or UL approval

The Xgard-1-H2 is a single-gas Gas Leak Detector used to warn for gases (Hydrogen, H₂, 0 ... 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Hydrogen, H₂, 0 ... 2000 ppm)
- Additional display and alarm station
- ATEX or UL approval

The carbon dioxide gas leak detector PCE-WMM 100 consists of a main unit and a remote display. The CO2 gas leak detector PCE-WMM 100 is used to measure carbon dioxide and oxygen in a fixed location. The gas leak detector PCE-WMM 100 has two relays that can be used to control alarm lights or sounders.

- Measuring range CO2: 0 .... 50000 ppm
- Measuring range O2: 0 ... 30 %
- Measuring range temperature: 0 ... 50 °C / 32 ... 122 °F
- Main and remote unit
- Alarm relay
- 4 ... 20 mA analog outputs
- Acoustic alarm

- Up to 15 gases
- For flammable gases
- 500 mm / 19.6" sensor
- Visual, audible and haptic alarm

The Xgard-1-O3 is a single-gas Gas Leak Detector used to warn for gases (Ozone, O₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval