- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces 

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.2 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
- Incl. ISO calibration certificate

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

- Measuring range: Fe: 0 ... 5000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Measuring range: Fe: 0 ... 2500 µm, NFe: 0 ... 2500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 1500 µm, NFe: 0 ... 1500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO Calibration Certificate

The portable and easy-to-use roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

- Measuring range: Fe: 0 ... 2000 µm, NFe: 0 ... 2000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

- Measuring range: Fe: 0 ... 3000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces 
- Incl. ISO calibration certificate

The roughness tester PCE-RT 2000BT-ICA is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store
- incl. ISO Calibration Certificate

The roughness tester PCE-RT 2000-ICA is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- 3 different cut-off wavelengths
- PC software
- incl. ISO Calibration Certificate

- Measuring range: Fe: 0 ... 500 µm, NFe: 0 ... 500 µm
- Accuracy after foil calibration: ±(1% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO Calibration Certificate