- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

- Measuring range: 0 ... 2000 Ω
- Measuring principle: Continuity test / earth resistance measurement
- Multi-coloured, backlit LCD
- Installation category III
- 50/60 Hz operating voltage

Electrical Tester for insulation resistance up to 2000 MΩ

- Measuring ranges AC voltage: 0 ... 750V
- Resolution AC voltage: 1V
- Accuracy AC voltage: ± 1.2% ± 10 dgts
- Complies with IEC1010-1, CAT III 1000V
- Large display with backlight
- Individual measurement and duration measurement

 

This electrical tester was developed for the indirect measurement of AC/DC currents as well as the frequency. A non-contact voltage tester function and a torch/flashlight for illuminating the measuring point have also been integrated into this electrical tester.

- AC/DC current, AC voltage and frequency measurement
- AC voltage test (contactless test):
   100 VAC to 600 VAC 50/60Hz 100 VAC to 600 VAC 50/60Hz
- DCA zero point function

Parameter:
- AC voltage, DC voltage
- AC / DC
- Resistance, conductivity
- Capacitance measurement, temperature
- Frequency measurement , duty cycle ratio
- Pulse width, continuity test
- Diode test

Digital Clamp Meter for measuring AC/DC current, AC voltage and resistance. This clamp meter is designed to indirectly detect AC/DC current and ohms. The clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The clamp meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in

 

PCE-PCM 1 is a multipurpose electrical tester or power analyzer used to measure alternating current (AC), voltage (TRMS) and frequency to determine active (kW), apparent (kVA) and reactive (kVAR) power as well as active energy (kWh) consumption. Both the phase angle and the power factor (cos φ) are shown on the handheld power meter's large and easy-to-read backlit display.

- Voltage (50 ... 200 Hz): 100 / 400 / 750V, ± (1.2% + 5 digits)
- Internal memory: Stores up to 99 measurement values
- Includes USB cable and PC software
- Three-phase power measurement
- True RMS

The Electrical Tester has been designed to detect, indirectly, AC/DC current and frequency. The Electrical Tester has a flashlight integrated to allow for the point of measurement to be illuminated, and a function to test the voltage without contact.

- AC current (50/60 Hz): 200 A / 0.1 A or 100-mA / ±3.0% + 8 digits
- DC current: 200 A / 0.1 A or 100-mA / ±2.8% + 8 digits
- AC test voltage (without contact):100 VAC to 600 VAC 50 / 60 Hz
- Frequency (3 ranges): 40 to 50 Hz / 51 to 510 Hz/ 0.51 to 1 kHz

 

Measuring function:
- DC voltage
- AC voltage
- Alternating current
- Resistance
- Capacity
- Frequency
- Type K temperature measurement
- Diode test
- Continuity test

Measuring function
- DC DC
- AC voltage AC (TRMS)
- AC + DC TRMS voltage
- DC DC
- AC AC (TRMS)
- 4 ... 20-mA %
- AC AC / Rogowski coil
- Resistance
- Frequency
- Duty cycle
- Capacity
- Temperature / thermocouple

Measurement functions
- DC power
- AC power
- DC voltage
- AC voltage
- Resistance
- Frequency (direct)
- Frequency (current clamp)

The Electrical Tester tests 12V and 24V starter batteries. The vehicle battery tester checks the condition of the car battery via the battery voltage in the charging cycle, when starting or when idling. 

 

- Measurement object:  12V / 24V starter batteries

- Battery standards: DIN, JIS, EN, SAE

- Power supply: 9 ... 35V DC via test voltage

The mobile electrical tester Easycount-3-32-A is an energy meter, installed in a splash-proof and impact-resistant housing, for three-phase current up to 400 V. The approx. 50 cm / 19.6" long cable ends of the mobile electrical tester are equipped with a CEE plug and a CEE coupling.

- Display: 6+1 roller counter
- Resolution: 0.1 kWh
- Degree of protection meter: IP 54
- Counter calibrated

The mobile electrical tester Easycount-3-16-A is an energy meter, installed in a splash-proof and impact-resistant housing, for three-phase current up to 400 V. The approx. 50 cm / 19.6" long cable ends of the mobile electrical tester are equipped with a CEE plug and a CEE coupling.

- Display: 6+1 roller counter
- Resolution: 0.1 kWh
- Degree of protection meter: IP 54

Measurement function:
- AC
- DC
- DC voltage
- AC voltage
- LowZ AC / DC
- Resistance
- Continuity test
- Diode test
- Capacities
- Temperature (type K)
- Frequency (with the current clamp)
- Frequency (during voltage measurement)
- frequency (direct measurement)
- Duty cycle

- Measuring range: 75 ... 600V AC
- 3-phase rotating field detection
- AC / DC voltage measurement
- CAT III 600V

The Easycount-1-CEE-G energy meter is an electricity meter for alternating voltages up to 230 V, enclosed in a splash-proof and impact-resistant housing. The cable ends of the Easycount-1-CEE-G energy meter are equipped with male and female connectors.

- Calibrated counter
- Voltage input: 230 VAC
- Current rating: 16 A
- Frequency: 50 HZ

 

The Easycount-1-Schuko-G energy meter is an electricity meter for alternating voltages up to 230 V, enclosed in a splash-proof and impact-resistant housing. The cable ends of the Easycount-1-Schuko-G energy meter are equipped with male and female connectors.

- Calibrated counter
- Voltage input: 230 VAC
- Current rating: 16 A
- Frequency: 50 HZ