Electrical tester to determine indirectly, the AC/DC currents with high accuracy.

- AC current (50 / 60 Hz): 2 A  / 1-mA / ± 2.8% + 10 dgt
- DC current: 2 A / 1-mA / ± 3.0% + 10 dgt
- AC overload protection: 100V AC up to 600V AC 50 / 60 Hz
- Incl. ISO Calibration Certificate

Electrical tester for measuring AC/DC current, AC voltage and resistance. This electrical tester is designed to indirectly detect AC/DC current and ohms. The electrical tester has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The electrical tester comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in
- Incl. ISO Calibration Certificate

Electrical Tester for insulation resistance up to 2000 MΩ

- Measuring ranges AC voltage: 0 ... 750V
- Resolution AC voltage: 1V
- Accuracy AC voltage: ± 1.2% ± 10 dgts
- Complies with IEC1010-1, CAT III 1000V
- Large display with backlight
- Individual measurement and duration measurement

The electrical tester PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the electrical tester, or you can use the integrated clamp mechanism. By using the clamp of the electrical tester, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

PCE-PCM 1 is a multipurpose electrical tester or power analyzer used to measure alternating current (AC), voltage (TRMS) and frequency to determine active (kW), apparent (kVA) and reactive (kVAR) power as well as active energy (kWh) consumption. Both the phase angle and the power factor (cos φ) are shown on the handheld power meter's large and easy-to-read backlit display.

- Voltage (50 ... 200 Hz): 100 / 400 / 750V, ± (1.2% + 5 digits)
- Internal memory: Stores up to 99 measurement values
- Includes USB cable and PC software
- Three-phase power measurement
- True RMS

Electrical Tester to test leakage / RMS measurement / continuity and resistance test.

- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included

Electrical Tester to determine indirectly, the AC/DC currents with high accuracy.

- AC current (50 / 60 Hz): 2 A  / 1-mA / ± 2.8% + 10 dgt
- DC current: 2 A / 1-mA / ± 3.0% + 10 dgt
- AC overload protection: 100V AC up to 600V AC 50 / 60 Hz

Digital Clamp Meter for measuring AC/DC current, AC voltage and resistance. This clamp meter is designed to indirectly detect AC/DC current and ohms. The clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The clamp meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in

By using the electrical tester PCE-CM 4, you are able to perform AC measurements on electrical conductors without having to disconnect them. Just put the flexible clamp of the electrical tester around the conductor to be measured and start the measurement. The flexible design of the clamp allows measurements even on hard to reach conductors.

- Range: 4 A / 40 A / 400 A AC
- Resolution: 0.001 A / 0.01 A / 0.1 A AC
- Accuracy: ± 3 %
- Easy to use

The Electrical Tester tests 12V and 24V starter batteries. The vehicle battery tester checks the condition of the car battery via the battery voltage in the charging cycle, when starting or when idling. 

- Measurement object:  12V / 24V starter batteries

- Battery standards: DIN, JIS, EN, SAE

- Power supply: 9 ... 35V DC via test voltage