Material Tester

PCE-5000 is a portable material hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.

• Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
• Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
• Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
• Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
• Memory size: 1,000 groups for measurement data and 20 groups for calibration data
• Different probe types (also automatic motorized probes) available

• torque: 0.1 ... 2000 Nm
• accuracy: ±1 % of Rd
• real-time curve
• display of the direction of rotation
• units Nm, kgf cm, lbf in
• USB interface
• adjustable limit values
• peak hold
• 7-inch touchscreen

The PCE-DDA 10 Shore A Material Tester is a portable handheld device used to check Shore A hardness in soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).

• Portable handheld digital device
• For Shore A hardness testing
• Single and serial measurements
• Data transfer to PC

The PCE-HT-75 Material Tester for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Material Tester in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.

• Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
• Measuring range: 10 … 70 N/mm²
• Energy: 0.735 J / 0.54 ft-lbs
• Low strength concrete testing or Type L
• Indication of measurement: 0 to 100 (without dimensions)
• Maximum thickness of concrete (of the material): 70 cm

The PCE-TG 300-P5EE is a material tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material tester. Wall thicknesses under a coating can also be measured with the material tester.

• Measuring range: P-E: 2 … 600 mm / 0.07 … 23.62", E-E: 2.5 … 100 mm / 0.09 …3.93"
• Diameter: 10mm / 0.39"
• Minimum diameter of pipes: 20 x 3 mm / 0.787 … 0.118"
• Frequency: 5MHz
• Bluetooth

The PCE-TG 300-P5EE is a material tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material tester. Wall thicknesses under a coating can also be measured with the material tester.

• Measuring range: P-E: 2 … 600 mm / 0.07 … 23.62", E-E: 2.5 … 100 mm / 0.09 …3.93"
• Diameter: 10mm / 0.39"
• Minimum diameter of pipes: 20 x 3 mm / 0.787 … 0.118"
• Frequency: 5MHz
• Bluetooth
• incl. ISO calibration certificate

The PCE-TG 300-NO5/90 is a material tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material tester. Wall thicknesses under a coating can also be measured with the material tester.

• Measuring range: 1 … 600 mm / 0.039 … 23.62" (steel)
• Diameter: 10mm / 0.39"
• Sensor at 90° angle
• Minimum diameter of pipes: 20 x 3 mm / 0.787 … 0.118"
• Frequency: 5 MHz
• Bluetooth