Material Tester

Material testing equipment is used to determine geometric and physical quantities. In most cases, material testers use a known factor or unit to draw conclusions about the measured value/parameter. Measuring tools determine whether the tested object complies with the required conditions or not. In addition to the display of values that enable a real measurement, a statement, i.e. a rating, can also be output. Particularly accurate measuring tools can be used to test other measuring instruments.

Digital calipers (popularly known as callipers), micrometers, thickness gauges, endoscopes, dial gauges can all be found here. Some of these measuring tools have a data interface, corresponding cables and software to record the data obtained by means of the measuring tools and to evaluate them on the computer. Many measuring tools are calibrated and can optionally be equipped with an ISO 9000 calibration certificate.

If you have any questions, please contact us at or +44 ( 0 ) 161 464902 0.

Material Tester PCE-XXM 30

£ 325.00

Price excl. VAT &. delivery

The material tester is designed for fast and precise color measurements of surfaces. The color ranges CIE-LAB, CIE-LCh, HunterLab, CIE-Luv, XYZ, RGB of the color can be determined with the material tester.

Measuring aperture: Ø8 mm / 0.31"
Wavelength interval: 10 mm / 0.39"
Wavelength: 400 … 700 nm
Battery life for approx. 10,000 measurements
Bluetooth interface
Requiresfree app for Android only in Playstore (PCE-XXM 30) to use all features
Various adjustable light sources

Material Tester PCE-XXM 30-ICA incl. ISO Calibration Certificate

£ 708.00

Price excl. VAT &. delivery

Measuring aperture: Ø8 mm / 0.31"
Wavelength interval: 10 mm / 0.39"
Wavelength: 400 … 700 nm
Battery life for approx. 10,000 measurements
Bluetooth interface
Requiresfree app for Android only in Playstore (PCE-XXM 30) to use all features
Various adjustable light sources
incl. ISO Calibration Certificate

Material Tester PCE-CT 26FN

£ 183.00

Price excl. VAT &. delivery

The PCE-CT 26FN material tester can measure non-destructive coatings (paints, plastics …) on steel / iron and non-ferrous metals. The PCE-CT 26FN material tester is ideally suited to immediately detect, for example, accident damage to the vehicle.

Measuring range: 0 … 1250 μm / 0 … 49.2 mils
Resolution: 1 μm / 0.039 mils
Accuracy: ± (3% + 2 μm / 0.079 mils)
Wear-resistant sensor
V-groove for measurement on pipes

Material Tester PCE-CT 26FN-ICA Incl. ISO Calibration Certificate

£ 322.00

Price excl. VAT &. delivery

Measuring range: 0 … 1250 μm / 0 … 49.2 mils
Resolution: 1 μm / 0.039 mils
Accuracy: ± (3% + 2 μm / 0.079 mils)
Wear-resistant sensor
V-groove for measurement on pipes
Incl. ISO calibration certificate

Material Tester PCE-UCD 100

£ 4,672.00

Price excl. VAT &. delivery

The material testing device sets a new standard for quality control of concrete structures. With a wide range of measurement parameters and state-of-the-art technology, this material testing device enables accurate verification of concrete piles, concrete beams, and other components. This innovative material testing device not only provides reliable concrete strength measurements but also detailed error detection, including the size and depth of voids and cracks.

Measurement range: -1677700 µs to +1677700 µs
Resolution: 0.05 µs
Measurement parameters: Concrete strength, error detection, size and depth of voids, cracks
Includes a camera for measuring crack width
Bandwidth: 1 to 500 kHz
Display: 10.1" TFT touchscreen display
Internal storage: 8 GB

Material Tester PCE-DDA 10-ICA incl. ISO Calibration Certificate

£ 703.00

Price excl. VAT &. delivery

The PCE-DDA 10 shore Material Tester is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 Material Tester is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units.

Handheld device
For Shore A measurements
Single and Serial Measurements
Data transfer to pc
Incl. ISO Calibration Certificate

Material Tester PCE-DDD 10 Shore D

£ 566.00

Price excl. VAT &. delivery

The PCE-DDD 10 Shore D Material Tester is a portable handheld device used to check Shore D hardness in hard rubber and thermoplastic. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).

Portable handheld digital device
For Shore D hardness testing
Single and serial measurements
Data transfer to PC

Material Tester PCE-DDD 10-ICA incl. ISO Calibration Certificate

£ 700.00

Price excl. VAT &. delivery

The PCE-DDD 10 shore Material Tester is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.

Handheld device
For Shore D measurements
Single and Serial measurements
Data transfer to PC
Incl. ISO Calibration Certificate

Material Hardness Tester for Metal PCE-2600N

£ 1,285.00

Price excl. VAT &. delivery

The Material Hardness Tester for Metal PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the material tester PCE-2600N to determine the surface hardness of many metals. The material tester PCE-2600N is especially suitable for quality or product inspection.

Measurement according to Leeb Rebound method
Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS
Accuracy: ± 0.5%, Repeatability: ± 0.8%
Impactor: DL
Display: 128 x 64 OLED