HVAC Meter / HVACR Tester

The PCE-VT 1100S HVAC meter is suitable for relative measurements on various machines. With the 45 mm long needle probe, you can access hard-to-reach places in machines and motors. For this reason, this HVAC meter is used for rapid measurement of imbalance and for checking bearing and gear conditions.

- Frequency range: 10 Hz ... 1 kHz
- Measures speed, distance, acceleration in metric units
- Holds the reading after each measurement
- Portable and battery operated
- Needle probe: 45mm / 1.77"

The HVAC meter PCE-HVAC 4 is a versatile measuring instrument for the determination of differential pressure, differential temperature and ambient temperature. The measurements of the HVAC meter PCE-HVAC 4 are via measuring terminals, thermocouples and an internally installed NTC sensor.

- Various parameters: psi, kPa, inHg, amHg, bar, °C, °F
- Measuring range: -96.5 to 3447.5 kPa / -14 to 500 psi / -0.97 to 34.48 bar
- Pressure Resolution: 689.5 Pa / 0.1 psi / 0.0069 bar
- Temperature Measuring range: -60 ... 537°C / -70 ... 998°F
- Built-in ambient temperature sensor-
- Battery warning indicator
- Overload indicator

The HVAC meter PCE-PDA 01L is a reliable differential pressure gauge for pressure measurement of gases in the range of ± 200 Pa. The HVAC meter PCE-PDA 01L has many different pressure measuring functions.

- Measuring range: ± 200 Pa  / 0.029 psi / 0.002 bar
- Resolution: 0.1 Pa / 0.0000145 psi / 0.000001 bar
- Accuracy: ± 1% of final value
- Min and Max value memory
- Data logger and leak test
- Temperature measurement, flow measurement

PCE-HVAC 3 is a multifunction HVAC meter, tester or diagnostic measuring device used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the meter calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the PCE-HVAC 3 meter.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F

The IR HVAC Meter was designed for taking non-contact temperature measurements. To get accurate readings, the emissivity of the thermometer can be adjusted, depending on the operation purpose. Besides taking infrared images, the thermometer can also take normal pictures, as well as a mixture of both, due to the built-in digital camera.

- Measurement range: -20 ... 300°C / -4 ... 572°F
- Accuracy: ± 2%, ± 2°C / 3.6°F
- Frequency image recording: 9 Hz
- Camera: 32 x 31 Pixel

PCE-VA 20 is a multifunction HVAC meter for testing heating, ventilation and air conditioning or cooling (HVAC) systems. This combination anemometer-hygrometer-thermometer features a 10 cm / 3.9" Ø fan impeller, easy-to-read backlit LCD, and functions such as display hold, average value, maximum value, minimum value, battery-saving automatic power off, low-battery indicator, and metric or imperial unit selection.

- Measures air flow velocity, volume flow, relative humidity, air temperature, dew
  point temperature and wet-bulb temperature
- Air flow velocity range: 0.2 ... 30 m/s (39.4 ... 5905.5 fpm)
- Accuracy: ±(1.5% of measured value + 0.3 m/s) when less than 20 m/s, ±(3% of
  measured value + 0.3 m/s) when more than 20 m/s
- Resolution: 0.1

PCE-VA 20-SET is a multifunction HVAC meter with capture hoods for assessing and balancing heating, ventilation and air conditioning or cooling (HVAC) systems. This combined hygrometer-anemometer-thermometer possesses a 10 cm / 3.9" diameter fan impeller and a bright backlit LCD. The functions of the HVAC device incorporate display hold, mean value, max value, min value, battery-saving auto shutdown, low-battery display, and a choice between metric and imperial units.

- Measures air flow velocity, volume flow, relative humidity, air temperature, dew
  point temperature and wet-bulb temperature
- Air flow velocity range: 0.2 ... 30 m/s (39.4 ... 5905.5 fpm)
- Accuracy: ±(1.5% of measured value + 0.3 m/s) when less than 20 m/s, ±(3% of
  measured value + 0.3 m/s) when more than 20 m/s
- Resolution: 0.1°C / 0.18°F
- Includes 2 x capture hoods (1 x round 210 mm / 8.3 in Ø, 1 x square 346 x 346
  mm / 13.6 x 13.6 in)

The PCE-VA 20 is a versatile multifunction HVAC meter for determining environmental conditions such as wind, temperature and humidity. It is additionally used to test heating, ventilation and air conditioning / cooling (HVAC) systems. This triple thermometer-hygrometer-anemometer device has a 10 cm / 3.9" Ø fan impeller and a clear backlit LCD. Available functions include display hold, average / maximum / minimum value, auto shutdown, low-battery warning, and metric / imperial choice.

- Measures air flow velocity, volume flow, relative humidity, air temperature, dew
  point temperature and wet-bulb temperature
- Air flow velocity range: 0.2 ... 30 m/s (39.4 ... 5905.5 fpm)
- Accuracy: ±(1.5% of measured value + 0.3 m/s) when less than 20 m/s, ±
  (3% of measured value + 0.3 m/s) when more than 20 m/s
- Resolution: 0.1
- Incl. ISO Calibration Certificate 

PCE-TDS 100H is a portable handheld clamp-on ultrasonic flow meter or HVAC meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 57 … 720 mm / approx. 2 ... 28 in.  Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 50 … 700, 57 … 720 mm (approx. 2 … 28")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-M1

PCE-TDS 100HS is a portable handheld clamp-on ultrasonic flow meter or HVACR meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 15 … 100, 20 … 108 mm (approx. 3/4 … 4")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, (N,W)
- Incl. sensors TDS-S1

PCE-TC 29 is an IR HVAC meter or infrared imaging camera used for visual inspection and non-contact infrared (IR) temperature measurement. Ideal for industrial use in electrical, mechanical, and building installations (such as in the auditing of machines, engines, or heating, ventilation, and air conditioning (HVAC) systems), this affordable infrared imager captures and saves 60 x 60 pixel IR resolution images to the included MicroSD card memory.

- IR Resolution: 60 x 60 pixels
- Temperature measuring range: -20 ... 300°C / -4 ... 572°F
- IR image, visual image, picture-in-picture
- Hot / cold spot localisation
- Field of view: 20 x 20°
- Adjustable emissivity from 0.1 ... 1.0
- Frequency image recording: 6 Hz
- Data storage: Micro SD

The HVAC Meter PCE-779N measures temperatures quickly and without contact. The HVAC Meter can be used for almost all surfaces. The emissivity of the HVAC Meter is adjustable over the range of 0.1 ... 1.0. The HVAC Meter has various measurement functions such as max, min and average measurement.

- OLED-Display
- Measuring range: -60 ... 760°C / -76 ... 1400°F
- Additional thermocouple measurement -64 ... 1400°C / -83.2 ... 2552°F
- Dual Laser
- Resolution: 0.1°C / 0.18°F at -83.2 ... 999.9°C (-117.8 ... 1831.8°F), otherwise 1°C / 1.8°F

PCE-330 is a multifunction digital HVAC meter or hygro-thermometer with a quick-response sensor for determining ambient temperature, relative humidity and dew point temperature. Equipped with an easy-to-read dual display, this data-logging indoor air quality (IAQ) meter features a large internal memory with storage for up to 16,000 recorded values.

- Temperature range: -20 ... 60°C / -4 ... 140°F
- Relative humidity range: 0 ... 100% RH
- Resolution: 0.1° / 0.18°F
- Accuracy: ± 0.8°C / ± 1.5°F, ± 2.0 ... 4.0% RH

This HVAC meter is very economical. With this HVAC meter you can measure wind speed and air temperature. The readings can be stored in the device and then transferred to a computer for further analysis. These test instruments are calibrated by the manufacturer. An ISO calibration certificate is available as an option.

- Speed measurement up to 45 m/s or 100 mph
- Wind speed: 0.01 m/s, accuracy ±3% ±0.1
- Air temperature: 0.2°C / 32.4°F, accuracy ±1°C / 33.8°F
- Air flow: 0.001 to 100, accuracy calculated from the wind speed and surface

This HVAC Data Logger meter is very economical. With this HVAC Data Logger meter you can measure wind speed and air temperature.

- Speed measurement up to 45 m/s or 100 mph
- Measures wind speed and air temperature (also calculates volumetric flow)
- Sampling rate: 1/ sec.
- Stores up to 2000 readings
- Incl. ISO calibration certificate

This HVAC meter has a good relation between price and quality and it combines accuracy and versatility with the ability to transfer data directly to a computer. This HVAC meter forms a part of a professional's basic equipment to regulate and test ventilation systems. All the test instruments come manufacturer calibrated. ISO certification can be made as an option.

- Measurement range: 0.2 ... 20.0 m/s
- Measurement range: 0.0 ... 50.0°C / 32 ... 122°F (sensor)
- Volume of air current:  0 ... 36,000 m³/min
- Internal memory: 16,000 values
- Sampling rate: 1 sec

HVAC data logger to measure air temperature and velocity with calculation of volume of air current and RS-232. This kind of airflow meter is mainly for use in HVAC systems. The logging instruments are manufacturer calibrated and are delivered incl. ISO calibration certificate.

- Measurement range: 0.2 ... 20.0 m/s
- Measurement range: 0.0 ... 50.0 °C / 32 ... 122°F (sensor)
- Volumetric flow:  0 ... 36,000 m³/min
- Internal memory: 16,000 values
- Incl. ISO calibration certificate

With the PCE-890U HVAC meter, measurements of surface temperatures can be carried out quickly and easily. Since the HVAC meter uses infrared radiation for temperature measurement, no direct contact with the measuring object is required. The HVAC meter makes it easy to measure objects from a distance that are difficult to access.

- Measuring range: -50 ... 1150°C / -58 ... 2102°F
- Accuracy: ± 1.5% ± 2°C / 3.6°F (0 ... 500°C / 32 ... 932°F)
- Resolution: 0.1°C / 0.18°F (<1000°C / 1832°F)
- Emission level: 0.1 ... 1

PCE-313A is a combination thermometer hygrometer used to measure the relative humidity (% RH) and temperature (°C / °F) of the air. Ideal for use in evaluating heating, ventilation and air conditioning (HVAC) system performance, this digital HVAC meter also has a port for connecting a type-K thermocouple.

- Relative humidity: 5 ... 95% r.H.
- Temperature: 0 ... 50°C / 32 ... 122°F
- Type K: -50 ... 1300°C / -58 ... 2372°F
- Calculated dew point: -25.3 ... 48.9°C / -13.5 ... 120°F
- Wet bulb temperature: -21 ... 50°C / -5.8 ... 122°F
- Memory: SD card (1 ... 16 GB)

The PCE-313A HVAC Meter measures relative humidity and temperature and can be used in the air-conditioning sector. The PCE-313A HVAC Meter can be connected to type K thermo-elements to detect, for instance, the temperature of a wall by means of a surface probe. The internal memory of this test equipment allows the HVAC Meter to record humidity and temperature data at an adjustable measurement interval. Thanks to its SD memory card (1 to 16 GB) the humidity test instrument can be used for long term data acquisition.

- Relative humidity: 5 ... 95% r.H.
- Temperature: 0 ... 50°C / 32 ... 122°F
- Type K: -50 ... 1300°C / -58 ... 2372°F
- Calculated dew point: -25.3 ... 48.9°C / -13.5 ... 120°F
- Wet bulb temperature: -21 ... 50°C / -5.8 ... 122°F
- Memory: SD card (1 ... 16 GB)
- incl. ISO Calibration Certificate

The PCE-HT110 HVAC Meter or Humidity Detector precisely measures air temperature and relative humidity. This accurate and reliable device shows the current measurements on the large LCD display and saves the measurement data directly to an SD card (included). The PCE-HT110 is equipped with two channels, accommodates an SD card memory of up to 16 GB, offers an adjustable measurement rate / sampling interval, and includes a wall mount, making the device ideal for logging data over an extended period of time.

- Measurement ranges: 0 … 50°C / 32 ... 122°F, 10 ... 90% RH
- Resolution: 0.1°C / 0.18°F, 0.1% RH
- Data format: .XLS (compatible with Microsoft Excel)

The PCE-HT110 HVAC Humidity / Temperature Data Logger or Humidity Detector precisely measures air temperature and relative humidity. This accurate and reliable device shows the current measurements on the large LCD display and saves the measurement data directly to an SD card (included). The PCE-HT110 is equipped with two channels, accommodates an SD card memory of up to 16 GB, offers an adjustable measurement rate / sampling interval, and includes a wall mount, making the device ideal for logging data over an extended period of time.

- Measurement ranges: 0 … 50°C / 32 ... 122°F, 10 ... 90% RH
- Resolution: 0.1°C / 0.18°F, 0.1% RH
- Data format: .XLS (compatible with Microsoft Excel)
- Set = Quantity of 5 x units

The PCE-HT110-ICA HVAC Humidity / Temperature Data Logger or Humidity Detector precisely measures air temperature and relative humidity. This accurate and reliable device shows the current measurements on the large LCD display and saves the measurement data directly to an SD card (included). The PCE-HT110-ICA is equipped with two channels, accommodates an SD card memory of up to 16 GB, offers an adjustable measurement rate / sampling interval, and includes a wall mount, making the device ideal for logging data over an extended period of time.

- Measurement ranges: 0 … 50°C / 32 ... 122°F, 10 ... 90 % RH
- Resolution: 0.1°C / 0.18°F, 0.1% RH
- Data format: .XLS (compatible with Microsoft Excel)
- incl. ISO Calibration Certificate

The PCE-IR10 HVAC Meter is made up of a small sensor head and a separate electrical component. The HVAC Meter sensor is so small that it can fit in almost any space. part from this, the device offers similar specifications as other devices.

- Temperature range: -40 ... 600°C / -40 ... 1112°F
- Accuracy: ± 1% or ± 1°C / 1.8°F
- Optical resolution: 15:1
- Storage conditions: -40 ... 85°C / -40 ... 185°F
- Spectral range: 8.0 ... 14 µm
- Emissivity: 0.100 - 1.000 adjustable in digital mode, by units of 0.001
- Outputs: analogue, USB, RS-232, RS-485, relay

The HVAC Meter with microprocessor is a high precision 1-channel temperature gauge. The HVAC Meter with microprocessor is ideal for use with various Pt100 sensors. Due to the fact that it uses 4-wire technology, it has a very fast response time and precision.

- 1 channel temperature recorder
- Automatic shutdown
- High accuracy of ± 2 % r.H.
- Sampling rate of 2 / sec
- Memory size: 5,000 values

HVAC Infrared Thermometer with LCD for continuous measurement of surface temperature of all solid materials, designed for fixed installation.

- Temperature range: -40 ... 600°C / -40 ... 1112°F
- Accuracy: ± 1% or ± 1°C / 1.8°F
- Optical resolution: 15:1
- Storage conditions: -40 ... 85°C / -40 ... 185°F
- Spectral range: 8.0 ... 14 µm
- Emissivity: 0.100 - 1.000 adjustable in digital mode, by units of 0.001
- Outputs: analogue, USB, RS-232, RS-485, relay
- Incl. ISO Calibration Certificate

The PCE-423 HVAC Meter with thermal sensor is highlighted by its good relation between price and quality. The PCE-423 HVAC Meter has a high resolution to be used for different applications. All the test instruments come manufacturer calibrated. ISO certification can be made as an option.

- Kind of sensor: Hot wire
- External
- Memory: No
- Interface: USB
- Measurement range: 0.1 ... 25.0 m/s, 0.2 ...55.8 mph
- Resolution: 0.01 m/s, 0.1 mph

PCE-HVAC 2 is a high-velocity multifunction HVAC meter with a pitot tube. This portable HVAC meter can be used to determine air speed, air pressure, air flow, differential pressure and ambient temperature. The pitot tube allows access through tiny openings to take measurements in small pipe systems and other confined spaces.-

- Measures air velocities up to 80 m/s / 262 ft/s, 2.24 ... 178.66 MPH  
- Zero, minimum, maximum, average, record and hold functions
- Stores to memory up to 99 measurement values per parameter

The PCE-HVAC 2 is a multifunction HVAC meter with a pitot tube that measures air velocities up to 80 m/s. It is possible to measure air speed, air pressure, air flow, differential pressure and ambient temperature with this mobile HVAC meter. Readings can be taken in narrow pipes and other restricted spaces because the pitot tube can be inserted in very small gaps.-

- Measures air velocities up to 80 m/s / 262 ft/s, 2.24 ... 178.66 MPH  
- Zero, minimum, maximum, average, record and hold functions
- Stores to memory up to 99 measurement values per parameter
- Includes ISO calibration certificate

The PCE-T390 HVAC meter is a digital device with four input channels for type K and type J temperature sensors and two input channels for PT100 temperature sensors. The PCE-T390 HVAC meter has a SD card slot (from 1 to 16 GB) for storing the measured data. The data is stored in xls format on the SD card of the HVAC meter so that no additional software is needed for further analysis.

- 4 input channels for type-K, J temperature sensors
- 2 input channels for Pt100 temperature sensors
- 2 x type-K TF-500 temperature sensors are included in the package
- SD card memory (1 ... 16 GB)

The PCE-T390 HVAC data logger is a digital device with four input channels for type K and type J temperature sensors and two input channels for PT100 temperature sensors. The PCE-T390 HVAC data logger has a SD card slot (from 1 ... 16 GB) for storing the measured data.

The data is stored in xls format on the SD card of the data logger so that no additional software is needed for further analysis. These temperature logging instruments are manufacturer calibrated and the delivery includes an ISO calibration certificate.

- 4 input channels for type-K, J temperature sensors
- 2 input channels for Pt100 temperature sensors
- 2 x type-K TF-500 temperature sensors are included in the package
- Sampling rate: 1/ sec.
- SD card memory (1 ... 16 GB)
- Incl. ISO calibration certificate

HVAC Meter with network Analyzer / Clamp on Tester with data logger.

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records

This HVAC meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The HVAC meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Voltage range: 50.0 V ... 600.0 V True RMS value
- Current range: 3.0 A ... 999.9 A True RMS value
- Includes clamps, clips, leads, PC software and data cable
- Data logger of 10,000,000 records at 5/10/30/60/120 second interval options
- For measurement in real time and over an extended time period up to 578 days @ 5 second sample rate

The HVAC Meter PCE-THA 10 is easy to operate with one hand thanks to its compact size, the new structure and integrated impeller. In addition to the wind speed, the HVAC meter measures the temperature, humidity, dew point, the wet bulb temperature and the air volume. Average wind speed values can be determined with the HVAC meter from the 20 preset points.

- Temperature measuring range: -15 ... 50°C / 5 ... 122°F
- Humidity range: 5 ... 95% RH
- Air speed: 0.4 ... 35 m / s
- Air flow: 0 ... 9.999 m³ / s
- Incl. ISO Calibration Certificate

The PCE-VA 20-SET is a multi-functional HVAC meter including flow hoods for assessing and balancing heating, ventilation and air conditioning or cooling (HVAC) installations. This multi-faceted anemometer-thermometer-hygrometer incorporates a 10 cm / 3.9" diam. fan impeller, easy-to-view backlit LCD, and useful functions, e.g. display hold, average val, maximum val, minimum val, auto power-off, low battery indication, and imperial/metric option.

- Measures air flow velocity, volume flow, relative humidity, air temperature, dew
  point temperature and wet-bulb temperature
- Air flow velocity range: 0.2 ... 30 m/s (39.4 ... 5905.5 fpm)
- Accuracy: ±(1.5% of measured value + 0.3 m/s) when less than 20 m/s, ±(3% of
  measured value + 0.3 m/s) when more than 20 m/s
- Resolution: 0.1°C / 0.18°F
- Includes 2 x capture hoods (1 x round 210 mm / 8.3 in Ø, 1 x square 346 x 346
  mm / 13.6 x 13.6 in)
- Incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Voltage range: 50.0 V ... 600.0 V True RMS value
- Current range: 3.0 A ... 999.9 A True RMS value
- Includes clamps, clips, leads, PC software and data cable
- Data logger of 10,000,000 records at 5/10/30/60/120 second interval options
- For measurement in real time and over an extended time period up to 578 days @ 5 second sample rate
- incl. ISO Calibration Certificate 

The PCE-ST 1 HVAC Meter is a handheld digital device to measure temperature in the HVAC sector, as for instance in heating ducts, air conditioning vents, insulation, crawl spaces, etc., thanks to its 120 mm / 4.7 in stainless steel probe. The HVAC Meter is very easy to use, with small dimensions and short response time.

- Measuring range:  -40 ... 250°C / -40 ... 482°F
- Indication of max. and min. values
- Data function
- Lock for continuous operation
- Measured value in ºC or ºF

PCE-MAM 2 is a lightweight portable handheld pocket-sized mini anemometer, wind speed meter or air velocity measuring device with an impeller wheel sensor that is ideal for determining air or wind speeds inside or out. This mini anemometer allows you to take velocity and temperature measurements quickly and on the spot.

- Velocity measuring range: 0.4 ... 30 m/s (0.9 ... 67 mph)
- Temperature measuring range: -20 ... 70°C / -4 ... 158°F
- Displays velocity measurements in m/s, km/h, mph, knots or ft/min
- Impeller wheel sensor for air or wind speed
- Colour display

The HVAC Meter PCE-777N measures non-destructively and from a distance, the temperature of surfaces via infrared beam. This small HVAC Meter is characterized by simple operation and the red sighting tool.

- Temperature range: -30 ... 260°C / -22 ... 500°F
- Measuring spot (measuring distance to measuring spot size): 8: 1
- Resolution: 0.1°C / 0.18°F

The HVAC Meter PCE-TH 5 is a universal temperature / humidity gauge which allows the measurement of both the ambient temperature and the ambient humidity, as well as the determination of the dew point and wet bulb temperature.

- Temperature measuring range: -20 ... 50°C / -4 ... 122°F
- Humidity measuring range: 0 ... 99.9% r.H.
- Resolution: 0.1°C / 0.18°F, 0.1% relative humidity
- Measurement accuracy: ±3% r.H. / ±0.6°C / 1.08°F
- Calculation of dew point and wet bulb temperature

The PCE-DC1 HVAC meter has been designed to detect, indirectly, AC/DC current and frequency. The HVAC meter has a flashlight integrated to allow for the point of measurement to be illuminated, and a function to test the voltage without contact.

- AC current (50/60 Hz): 200 A / 0.1 A or 100-mA / ±3.0% + 8 digits
- DC current: 200 A / 100-mA / ±2.8% + 8 digits
- AC test voltage (without contact): 100 VAC to 600 VAC 50 / 60 Hz
- Frequency: 40 to 50 Hz / 51 to 510 Hz/ 0.51 to 1 kHz

Digital Clamp Meter for measuring AC/DC current, AC voltage and resistance. This clamp meter is designed to indirectly detect AC/DC current and ohms. The clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The clamp meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in

- Measuring range: ± 13.8 kPa / ± 2 psi / ± 0.14 bar
- Measurement accuracy: ± 0.006 psi (0 ... 0.2 psi)
- Resolution: 6.9 Pa / 0.001 psi / 0.000069 bar
- Android and iOS app
- Bluetooth interface
- 11 different units

HVAC Meter PCE-DC3 to determine indirectly, the AC/DC currents with high accuracy.

- AC current (50 / 60 Hz): 2 A  / 1-mA / ± 2.8% + 10 dgt
- DC current: 2 A / 1-mA / ± 3.0% + 10 dgt
- AC overload protection: 100V AC up to 600V AC 50 / 60 Hz

PCE-EM 886 is a portable handheld multifunctional digital device used to measure sound, light, humidity, temperature, AC / DC current, electrical resistance, capacitance and frequency.

- Sound: 35 ...100 dB
- Light: 4,000 ... 40,000 lux
- Humidity: 33 ... 99% RH
- Temperature: 0 ... 50°C Indoor, -20 ... 1300ºC Type K
- Auto-ranging electrical multimeter

PCE-P05 is a portable handheld digital HVAC meter or differential pressure manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-P05 displays min / max / average values right on the meter's screen for comparison against current measurement values.

- Measuring Range: ± 34.5 kPa / ± 5 psi / ± 0.345 bar

- Resolution: 6.9 Pa / 0.001 psi / 0.000069 bar

- Displayable Units: bar, mmHg, ozin², kgcm², psi, inH2O, kPa, ftH2O, inHg, cmH2O, mbar

- Features real-time data-logging capabilities using the included PC software and USB cable

HVAC Meter PCE-LCT 1 to test leakage / RMS measurement / continuity and resistance test.

- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included

The HVAC Meter PCE-THA 10 is easy to operate with one hand thanks to its compact size, the new structure and integrated impeller. In addition to the wind speed, the HVAC Meter measures the temperature, humidity, dew point, the wet bulb temperature and the air volume.

- Temperature measuring range: -15 ... 50°C / 5 ... 122°F
- Humidity range: 5 ... 95% RH
- Air speed: 0.4 ... 35 m / s
- Air flow: 0 ... 9.999 m³ / s

PCE-PCM 1 is a multipurpose HVAC meter or power analyzer used to measure alternating current (AC), voltage (TRMS) and frequency to determine active (kW), apparent (kVA) and reactive (kVAR) power as well as active energy (kWh) consumption. Both the phase angle and the power factor (cos φ) are shown on the handheld power meter's large and easy-to-read backlit display.

- Voltage (50 ... 200 Hz): 100 / 400 / 750V, ± (1.2% + 5 digits)
- Internal memory: Stores up to 99 measurement values
- Includes USB cable and PC software
- Three-phase power measurement
- True RMS

Without a doubt, the main advantage of this handheld cup vane HVAC Meter is that it doesn't need to be held exactly in the direction of the wind. HVAC Meter with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane HVAC Meter, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

The HVAC meter PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the HVAC meter, or you can use the integrated clamp mechanism. By using the clamp of the HVAC meter, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

PCE-LD 1 is a portable handheld gas detector used to locate CFC/HFC refrigerant gas leaks. This highly sensitive gas leak detector can locate gas leaks from HVACR refrigeration systems even in areas contaminated by other gases. The gas sensor is located at the end of a 390 mm / 15.35 in flexible goose-neck tube, allowing unique access to hard-to-reach places.

- Adjustable high/low sensitivity:
    6 g/yr or 30 g/yr for R-22 and R-134a
    8 g/yr or 40 g/yr for R404A, R-407C and R-410A

PCE-T 318 is an HVAC temperature meter or digital contact thermometer used to measure temperature in laboratory, industrial and heating, ventilation, air conditioning and refrigeration (HVACR) systems and applications. Compatible with IEC751 PT100, PT500 and PT1000 sensors, this platinum resistance temperature detector (RTD) thermometer includes 1 x 4-wire PT100 class A sensor in the delivery contents. Additional sensors sold separately.

- Measuring range: -100 ... 300°C / -148 ... 572°F
- Resolution: 0.1°C / 0.18°F
- Accuracy: ± (0.1% of reading + 0.4°C / 0.72°F)

PCE-EM 888 is a portable handheld HVAC meter ideal for monitoring environmental conditions and the performance of heating, ventilation and air conditioning (HVAC) systems. This multifunctional digital device is used to measure wind speed, volumetric air flow, temperature, relative humidity, light and barometric pressure.

- Wind speed
- Volumetric air flow
- Air temperature
- Relative humidity
- Type K thermocouple sensor
- Barometric pressure
- Light

PCE-P15 is an HVAC meter or differential pressure manometer used to measure gauge pressure and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 103.4 kPa / 0 to 15 psi / 0 to 1.034 bar
- Resolution: 6.895 Pa / 0.001 psi / 0.000069 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F

PCE-P30 is an HVAC meter used to measure gauge and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 206.8 kPa / 0 to 30 psi / 0 to 2.07 bar
- Resolution: 138 Pa / 0.02 psi / 0.0014 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F

PCE-910 is a portable handheld digital HVAC meter or differential pressure manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-910 features a dust-proof, splash-resistant housing, allowing the meter to be used under adverse conditions.

- Pressure measuring range: ± 200 kPa / ± 29 psi / ± 2 bar
- Resolution: 100 Pa / 0.0145 psi / 0.001 bar
- 10 measurement units: psi, mbar, inH2O, mH2O, inHg, mmHg, Torr, Pa / kPa, atm, kg/cm²
- Optional PC software with RS-232 cable sold separately as a data transfer accessory

HVAC meter for measuring AC/DC current, AC voltage and resistance. This HVAC meter is designed to indirectly detect AC/DC current and ohms. The HVAC meter has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The HVAC meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.

- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in
- Incl. ISO Calibration Certificate

PCE-917 is a portable handheld digital HVAC meter or differential pressure manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-917 features a dust-proof, splash-resistant housing, allowing the meter to be used under adverse conditions.

- Pressure measuring range: ± 700 kPa / ± 101.5 psi / ± 7 bar
- Resolution: 500 Pa / 0.0725 psi / 0.005 bar
- 10 measurement units: psi, mbar, inH2O, mH2O, inHg, mmHg, Torr, Pa / kPa, atm, kg/cm²
- Optional PC software with RS-232 cable sold separately as a data transfer accessory

HVAC meter to determine indirectly, the AC/DC currents with high accuracy.

- AC current (50 / 60 Hz): 2 A  / 1-mA / ± 2.8% + 10 dgt
- DC current: 2 A / 1-mA / ± 3.0% + 10 dgt
- AC overload protection: 100V AC up to 600V AC 50 / 60 Hz
- Incl. ISO Calibration Certificate

PCE-932 is an easy-to-use, digital, handheld device for high pressure measurement in hydraulic and compressor systems, pumps, tanks and silos in chemical, manufacturing, plastics and HVAC industries. This portable pressure measuring device can be connected to pressure sensors with ranges up to 400 bar (each with a 1.2 m / 3.9 ft connecting cable). Please note: Pressure sensors are sold separately.

- Measuring range: 0 to 400 bar / 0 to 5801 psi, depending on sensor
- Measures system pressure in all media (e.g., gasses, liquids, etc.)
- Offers min, max and hold functionality 

PCE-P50 is an HVAC meter or differential pressure manometer used to measure gauge pressure and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 689.5 kPa / 0 to 100 psi / 0 to 6.9 bar
- Resolution: 689.5 Pa / 0.1 psi / 0.0069 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F

The HVAC Meter is used as a hand-held measuring device for the individual assessment of vibrations on machines and systems. With the help of this HVAC Meter, the actual state can easily be determined on site. Thus, corresponding changes can be made directly on site after the measurement.

- Frequency range: 10 Hz ... 1 kHz
- Measures speed, distance, acceleration in metric units
- Holds the reading after each measurement
- Easy to handle and battery operated
- Standard probe: 10mm

The HVAC meter PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the HVAC meter, or you can use the integrated clamp mechanism. By using the clamp of the digital HVAC meter, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism
- Incl. ISO Calibration Certificate

The PCE-THB 38 HVAC meter is ideal for detecting and digitally displaying humidity, temperature and barometric pressure. Temperature is measured by an RTD sensor and air humidity is measured by a highly repeatable, capacitive sensor. All products are test instruments, and the HVAC meter is sent out manufacturer calibrated. An ISO certification is available optionally.

With the PCE-320 HVAC Meter it is possible to measure climate conditions such as temperature and relative humidity, as well as determining surface temperature of objects simultaneously by using the included external temperature sensor or using an infrared measurement. The HVAC Meter offers features such as average value, maximum, minimum, and hold functions at a reasonable price.

- Internal probe
- Temperature: -20°C ... 60°C / -4 ... 140°F
- Relative humidity: 10 ... 90% r.H.
- Temperature of global: -22°C ... 60°C / -8 ... 140°F
- Humidity: -68°C ... 60°C / -90 ... 140°F
- Dew point temperature: depending on the sensor

- External probe
- Temperature: -50° C ... 500° C / -58 ... 932°F

The PCE-779N-ICA HVAC Meter measures temperatures quickly and without contact. The HVAC meter can be used for almost all surfaces. The emissivity of the HVAC meter is adjustable over the range of 0.1 ... 1.0. The HVAC meter has various measurement functions such as max, min and average measurement.

- OLED-Display
- Measuring range: -60 ... 760°C / -76 ... 1400°F
- Additional thermocouple measurement -64 ... 1400°C / -83.2 ... 2552°F
- Dual Laser
- Resolution: 0.1°C / 0.18°F at -83.2 ... 999.9°C (-117.8 ... 1831.8°F), otherwise 1°C / 1.8°F
- incl. ISO Calibration Certificate

PCE-HVAC 3 is a HVAC meter or diagnostic measuring device used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the HVAC meter calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the PCE-HVAC 3 HVAC meter.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F
- Incl. ISO calibration certificate

PCE-P05 is a portable handheld digital HVAC meter or differential pressure manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-P05 displays min / max / average values right on the meter's screen for comparison against current measurement values.

- Measuring Range: ± 34.5 kPa / ± 5 psi / ± 0.345 bar

- Resolution: 6.9 Pa / 0.001 psi / 0.000069 bar

- Displayable Units: bar, mmHg, ozin², kgcm², psi, inH2O, kPa, ftH2O, inHg, cmH2O, mbar

- Features real-time data-logging capabilities using the included PC software and USB cable

The PCE-JR-911 HVAC Meter with Thermometer is a versatile tool in that it can measure the temperature of objects without contact and readings can be stored in memory and transferred to a computer by way of its RS-232 interface and software. This HVAC Meter comes complete with a Thermometer, allowing the user to program specific time intervals for taking measurements, such as over an entire week.

- Temperature range: -40 to 500°C / -40 ... 932°F
- Resolution: 0.1°C / 0.18°F
- Accuracy: ±2% of reading or ±2°C / 3.6°F
- Optical resolution: 8:1
- Emissivity: 0.3 to 1.0 (adjustable)
- Interface: RS-232
- Display: LCD

The PCE-313 S HVAC Meter has been designed for professional use in fields such as the air-conditioning sector. The PCE-313 S HVAC Meter determines both relative humidity and ambient temperature. The PCE-313 S HVAC Meter can be connected to type K thermo-elements to detect, for instance, the temperature of a wall by means of a surface probe.

- Relative humidity: 5 ... 95% r.H.
- Temperature: 0 ... 50°C / 32 ... 122°F
- Type K: -50 ... 1300°C / -58 ... 2372°F
- Calculated dew point: -25.3 ... 48.9°C / -13.54 ... 120°F

The PCE-VE 200SV1 HVAC meter is a nondestructive inspection camera. Thus, the PCE-VE 200SV1 HVAC meter is the ideal instrument for diagnosing hard-to-reach areas. Thus, the areas of mechanical engineering, sanitary and heating construction, and the entire construction and construction industry are among the main applications of the HVAC meter PCE-VE 200SV1.

- Camera head diameter 9 mm / 0.4 in
- Cable length: 1 m / 3.3 ft 
- Interface: Micro USB 2.0
- Memory: Micro SD card
- Front and side view camera

With the PCE-890U-ICA HVAC Meter, measurements of surface temperatures can be carried out quickly and easily. Since the HVAC meter uses infrared radiation for temperature measurement, no direct contact with the measuring object is required. The HVAC meter makes it easy to measure objects from a distance that are difficult to access.

- Measuring range: -50 ... 1150°C / -58 ... 2102°F
- Accuracy: ± 1.5% ± 2°C / 3.6°F (0 ... 500°C / 32 ... 932°F)
- Resolution: 0.1°C / 0.18°F (<1000°C)
- Emission level: 0.1 ... 1
- incl. ISO Calibration Certificate

PCE-P15 is an HVAC meter or differential pressure manometer used to measure gauge pressure and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 103.4 kPa / 0 to 15 psi / 0 to 1.034 bar
- Resolution: 6.895 Pa / 0.001 psi / 0.000069 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F
- Incl. ISO calibration certificate

PCE-P30 is an HVAC meter used to measure gauge and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 206.8 kPa / 0 to 30 psi / 0 to 2.07 bar
- Resolution: 138 Pa / 0.02 psi / 0.0014 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F
- Incl. ISO calibration certificate

PCE-910 is a portable handheld HVAC Meter, digital differential pressure gauge or manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-910 features a dust-proof, splash-resistant housing, allowing the meter to be used under adverse conditions.

- Pressure measuring range: ± 200 kPa / ± 29 psi / ± 2 bar
- Resolution: 100 Pa / 0.0145 psi / 0.001 bar
- 10 measurement units: psi, mbar, inH2O, mH2O, inHg, mmHg, Torr, Pa / kPa, atm, kg/cm²
- Optional PC software with RS-232 cable sold separately as a data transfer accessory
- Incl. ISO calibration certificate

The HVAC meter PCE-VE 200SV3 is a nondestructive inspection camera. Thus, the HVAC meter PCE-VE 200SV3 is the ideal instrument for diagnosis in hard-to-reach places. For example, the areas of mechanical engineering, sanitary and heating engineering, and the entire construction and construction industry are among the main areas of application of the HVAC meter PCE-VE 200SV3.

- Camera head diameter 9 mm / 0.4 in
- Cable length: 3 m / 9.9 ft
- Interface: Micro USB 2.0
- Memory: Micro SD card
- Front and side view camera

PCE-917 is a portable handheld digital HVAC Meter, gauge or manometer used to measure differential pressure in pneumatic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. The PCE-917 features a dust-proof, splash-resistant housing, allowing the meter to be used under adverse conditions.

- Pressure measuring range: ± 700 kPa / ± 101.5 psi / ± 7 bar
- Resolution: 500 Pa / 0.0725 psi / 0.005 bar
- 10 measurement units: psi, mbar, inH2O, mH2O, inHg, mmHg, Torr, Pa / kPa, atm, kg/cm²
- Optional PC software with RS-232 cable sold separately as a data transfer accessory
- Incl. ISO calibration certificate

PCE-WB 20SD is a data-logging HVAC meter used to measure indoor / outdoor wet bulb globe temperature (WBGT), black globe temperature (TG), wet bulb temperature (WB), dew point temperature, air temperature (TA) and relative humidity. Thus, this multipurpose data-recording device is an ideal tool for evaluating heat stress risks in different work environments.

- Programmable WBGT alarm setting with audible and visual alerts
- Manual (push-button) or automatic (adjustable 1 ... 3600 sec) sampling
- SD card memory (1 ... 16 GB) allows for quick and easy data transfer to a PC

PCE-P50 is a HVAC meter used to measure gauge pressure and true differential pressure in pneumatic, hydraulic, compressor and pump installations, valves, tanks and heating, ventilation and air conditioning (HVAC) systems. 11 pressure units are selectable for Imperial and Metric measurement, including bar, mmHg, ozin², kgcm², psi, inH2, kPa, ftH2O|, inHg, cmH2O and mbar.

- Pressure measuring range: 0 to 689.5 kPa / 0 to 100 psi / 0 to 6.9 bar
- Resolution: 689.5 Pa / 0.1 psi / 0.0069 bar
- Accuracy: ± 0.3% of full scale at 25°C / 77°F
- Incl. ISO calibration certificate

PCE-330 is an HVAC meter or hygro-thermometer with a quick-response sensor for determining ambient temperature, relative humidity and dew point temperature. Equipped with an easy-to-read dual display, this data-logging indoor air quality (IAQ) meter features a large internal memory with storage for up to 16,000 recorded values.

- Temperature range: -20 ... 60°C / -4 ... 140°F
- Relative humidity range: 0 ... 100% RH
- Resolution: 0.1° / 0.18°F
- Accuracy: ± 0.8°C / ± 1.5°F, ± 2.0 ... 4.0% RH
- Incl. ISO calibration certificate

The HVAC meter PCE-PDA 100L is a reliable differential pressure gauge for pressure measurement of gases in the range of -100 to +200 kPa. The HVAC meter PCE-PDA 100L has many different pressure measuring functions.

- Measuring range: -100 ... 200 kPa  / -14.5 ...  29 psi / -1 ... 2 bar
- Resolution: 10 Pa / 0.00145 psi / 0.0001 bar
- Accuracy: ± 0.5% of final value
- Min and Max value memory
- Data logger and leak test
- Temperature measurement, flow measurement

The HVAC meter PCE-PDA 10L is a reliable differential pressure gauge for pressure measurement of gases in the range of ±20 kPa. The HVAC meter PCE-PDA 10L has many different pressure measuring functions.

- Measuring range: ± 20 kPa  / ± 2.9 psi / ± 0.2 bar
- Resolution: 10 Pa / 0.00145 psi / 0.0001 bar
- Accuracy: ± 0.5% of final value
- Min and Max value memory
- Data logger and leak test
- Temperature measurement, flow measurement
- Pitot tube not included in delivery / optionally selectable

The relative pressure HVAC meter PCE-PDA 1000L measures the relative pressure on machines and systems. The relative pressure is measured by this HVAC pressure meter in the range between -100 ... 2000 kPa. The relative pressure HVAC meter PCE-PDA 1000L has a quick coupling connection with which the air pressure or water pressure can be directly applied to the device.

- Measuring range pressure: -100 ... 2000 kPa relative  / -14.5 ... 290 PSI
- Resolution: 0.01 kPa, 0.1 kPa
- Accuracy: <± 0.5% of the measuring range
- USB interface
- Data logger
- Adjustable measuring units: Pa, hPa, kPa, MPa, mbar, bar, ATM, kg / cm², mmH2O, cmH2O, inH2O, mmHg, inHg, Torr, PSI, PSF

The HVAC meter PCE-PDA 1L is a reliable differential pressure gauge for pressure measurement of gasses in the range of ± 2 kPa. The HVAC meter PCE-PDA 1L has many different pressure measuring functions.

- Measuring range: ± 2000 Pa  / ± 0.29 psi / ± 0.02 bar
- Resolution: 1 Pa / 0.000145 psi / 0.00001 bar
- Accuracy: ± 0.5% of final value
- Min and Max value memory 
- Data logger and leak test 
- Temperature measurement, flow measurement

The HVAC meter PCE-PDA A100L is suitable for the measurement of atmospheric pressure. This HVAC meter records the pressure from absolute zero to 200 kPa. The HVAC meter can be used for many mobile applications in industry and crafts. 

- Measuring range pressure: 0 ... 200 kPa absolute
- Resolution: 0.01 kPa, 0.1 kPa
- Accuracy: < ± 0.5% of the measuring range
- USB interface
- Datalogger
- Different units

The PCE-G1 HVAC Meter has been designed for measuring relative humidity and temperature, with readings shown on its high visibility display. The HVAC Meter is composed of a 100mm high LED and comes with IP54 rating. Celcius only temperature display.

- Measurement ranges relative humidity / temperature: 10 to 95% r.h. / 0 to 60  °C
- Resolution relative humidity / temperature: 1% r.h. / 1 °C
- Accuracy relative humidity / temperature: ±2% r.h. / 1 °C
- Display: 100 mm high LED (alternates values)
- Protection: IP 54

PCE-WM1 is a multi-function HVAC meter used to determine relative humidity (% RH), absolute humidity (g/m³), air temperature, dew-point temperature and surface temperature (°C). This Metric-only measuring instrument comes complete with an external sensor probe for taking the surface temperature of different materials.

- Temperature range: -20 ... 80°C 
- Relative humidity range: 10 ... 95% RH
- Absolute humidity range: 0.5 ... 74.4 g/m³

PCE-T 1200 is a 12-channel temperature data logger that accommodates SD cards up to 16 GB in size. The optional software allows the temperature meter to connect to a PC via USB for direct data transfer and analysis via Microsoft Excel.

- 12-channel data logger for temperature (°C / °F)
- Works with type K, J, T, E, R and S thermocouple sensors
- Adjustable datalogging interval from 1 ... 3600 seconds per channel
- Includes 2 Type K sensors 1-meter in length

PCE-WM1-ICA is a multi-function HVAC meter used to determine relative humidity (% RH), absolute humidity (g/m³), air temperature, dew-point temperature and surface temperature (°C). This Metric-only measuring instrument comes complete with an external sensor probe for taking the surface temperature of different materials.

- Temperature range: -20 ... 80°C 
- Relative humidity range: 10 ... 95% RH
- Absolute humidity range: 0.5 ... 74.4 g/m³
- incl. ISO Calibration Certificate

PCE-G1A is an HVAC meter with a large display. This IP54-rated wall-mountable device measures both relative humidity (%RH) and temperature (°C only). The PCE-G1A HVAC meter has a large LED display with a number height of 100 mm / 3.9 in, so measurement values can be seen at a distance of up to 50 m / 164 ft away. Celcius only temperature display.

- Measurement ranges relative humidity / temperature: 10 ... 95% RH / 0 ... 60°C
- Resolution relative humidity / temperature: 1% RH / 1°C
- Accuracy relative humidity / temperature: ±2% RH / 1°C
- 2-channel analog output of 4 ... 20-mA
- Display: 100 mm / 3.9 in tall LED digits (alternates values) 

PCE-PA 8000 is a portable handheld power analyzer used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.

PCE-TDS 100H-ICA is a portable handheld clamp-on ultrasonic HVAC meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 57 … 720 mm / approx. 2 ... 28 in.  Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 50 … 700, 57 … 720 mm (approx. 2 … 28")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-M1
- Incl. ISO Calibration Certificate

PCE-TDS 100HS-ICA is a portable handheld clamp-on ultrasonic flow HVACR meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 15 … 100, 20 … 108 mm (approx. 3/4 … 4")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, (N,W)
- Incl. sensors TDS-S1
- Incl. ISO Calibration Certificate

PCE-TDS 100HSH is a portable handheld clamp-on ultrasonic flow test instrument or meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 15 … 700, 20 … 720 mm (approx. 3/4 … 28")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, (N,W)
- Incl. sensors TDS-M1 and TDS-S1

The PCE-830 HVAC Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVAC Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)