PCE Instruments

Hardness Tester

Order no.: PCE-DD-A

The PCE-DD-A hardness tester is used to measure Shore A hardness in soft gums, rubber, elastomers and more. Calibration is not available for this item.


- Measurement area: 0 ... 100 Shore A
- Resolution: 0.5
- Accuracy: ±1
- Depth of indentation: 0 ... 2.5 mm
- Indenter: 35°

 

Manufacturer: PCE Instruments
£ 53.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-DD-D

PCE-DD-D is a Shore D durometer or hardness tester. This Shore D hardness tester uses an impact rod with a 30 º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24". Calibration is not available for this item.


- For Shore D hardness testing of hard rubber, hard resin, acrylic, glass,
  thermoplastic and more
- Measurement range: 0 ... 100 Shore D
- Accuracy: ±2 Hardness - Grade


Manufacturer: PCE Instruments
£ 53.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-DX-AS

Mechanical hardness tester for measuring hardness of soft elastomer with drag needle. The shore hardness tester is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero. 

- Force of pressure: 0 to 12.5 N
- Penetrating body: 35º (according to Shore A)
- Measurement range: 10 to 90 (pressure diminishes below 10 and above 90)
- Margin of error: ±1
- Division of scale: 1


Manufacturer: PCE Instruments
£ 91.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-DDA 10

The PCE-DDA 10 shore hardness tester is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 durometer is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units. The durometer (as all test instruments) comes manufacturer calibrated and can additionally be lab certified to ISO standards.


- Handheld device
- For Shore A measurements
- Single and Serial Measurements
- Data transfer to PC

 

Manufacturer: PCE Instruments
£ 301.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-DDD 10

The PCE-DDD 10 shore hardness tester and durometer is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.  The durometer (as all test instruments) comes manufacturer calibrated and can additionally be lab certified to ISO standards.


- Handheld device
- For Shore D measurements
- Single and Serial Measurements
- Data transfer to PC

 

Manufacturer: PCE Instruments
£ 301.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² (1450.38 ... 8702.26 psi)
- Impact energy: 2207 J or N-m (1627.8 ft-lb)
- Impact stroke: 75 mm ± 0.3 mm (2.95" ± 0.012")
- Radius of spherical tip: 25 mm ± 1 mm (0.99" ± 0.04")
- kg/cm² and MPa conversion tables on back of instrument and in user manual

Manufacturer: PCE Instruments
£ 309.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-2500N

PCE-2500N is a portable handheld pen-sized digital material hardness tester, rebound hammer or durometer for use with metals. This high-accuracy hardness tester quickly and accurately measures the surface hardness of 10 common metal materials including steel, cast steel, alloy tool steel, stainless steel, cast iron, ductile iron, cast aluminum alloy, brass, bronze and copper.


- Displays measurements in Rockwell A, B or C (HRA, HRB or HRC), Brinell (HB),
  Vickers (HV), Shore (HS) or Leeb (HLD)
- Measurement ranges: HLD 170-960 / HRC 17.9-69.5 / HRB 3.5-101.7 / HB 19-683 / HV
  80-1042 / HS 30.6- 102.6 / HRA 59.1-88
- Accuracy: ±0.5 HLD
- Type D impact device
- Measuring principle: Rebound method

Manufacturer: PCE Instruments
£ 340.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-DDO 10

The PCE-DDO 10 hardness tester is an ergonomic device to check Shore O hardness in gum. It has been designed with a high quality. The PCE-DDO 10 hardness tester is mainly used for soft gums. If the material thickness is not enough, it should be tightened on the back with the same material in order to increase its thickness.


- Handheld device
- For Shore O measurements
- Single and Serial-Measurements
- Data transfer to PC

 

Manufacturer: PCE Instruments
£ 344.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-HT-75

The PCE-HT-75 Concrete Hardness Tester is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Hardness Tester in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 mm ±0.3 mm
- Measuring range: 10-70 N/mm²
- Energy: 0.735 J
- Low strength concrete testing
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
£ 383.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-A

Mechanical Hardness Tester for measuring the hardness of soft rubber and plastic.


- Shore A measurement on highest level
- Force: 12.5 N
- Penetrating body: 35°
- Diameter of dial: 57 mm
- Total length: 123 mm
- Follows ASTM D2240

 

Manufacturer: PCE Instruments
£ 405.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-A-S

Mechanical hardness tester for measuring the hardness of soft rubber and plastic.


- Shore A measurement instrument with pulling needle
- Force: 12.5 N
- Penetrating body: 35°
- Diameter of dial: 57 mm
- Total length: 123 mm
- Indication range: 0 to 100
- Measurement range: 10 to 90
- Error: ±0.5
- Follows ASTM D2240

 

Manufacturer: PCE Instruments
£ 450.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-D

Hardness tester for measuring the hardness of hard rubber and hard thermal plastic.


- Shore D testing device
- Force: 12.5 N
- Penetrating body: 35°
- Diameter of dial: 57 mm
- Total length: 123 mm
- Indication range: 0 to 100
- Measurement range: 10 to 90
- Error: ±0.5
- Follows ASTM D2240

 

Manufacturer: PCE Instruments
£ 450.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-D-S

Hardness tester for measuring the hardness of hard rubber and hard thermal plastic.


- Shore D test device with pulling needle
- Force: 12.5 N
- Penetrating body: 35°
- Diameter of dial: 57 mm
- Total length: 123 mm
- Indication range: 0 to 100
- Measurement range: 10 to 90
- Error: ±0.5
- Follows ASTM D2240

 

Manufacturer: PCE Instruments
£ 450.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-1000

Hardness tester ideal for testing surface hardness of metallic surfaces quickly. Operates on 9V rechargeable battery only. Included charger and test block. Manual striker is reset by user with included roll pin.


- Scales of hardness: STEEL, ALLOY STEEL, STAINLESS STEEL, GREY CASTIR,
  NODULAR CAST IRON, CAST aluminum, BRASS, BRONZE, COPPER.
- Accuracy: ±6 HL para HL = 800 (0.8%)
- Instrument of percussion: type D (integrated)
- Minimum hardness: 940 HV
- Minimum penetration: 0.8 mm

 

Manufacturer: PCE Instruments
£ 473.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-2500N-ICA

PCE-2500N-ICA is a portable handheld pen-sized digital material hardness tester, rebound hammer or durometer for use with metals. This high-accuracy hardness tester quickly and accurately measures the surface hardness of 10 common metal materials including steel, cast steel, alloy tool steel, stainless steel, cast iron, ductile iron, cast aluminum alloy, brass, bronze and copper.


- Displays measurements in Rockwell A, B or C (HRA, HRB or HRC), Brinell (HB),
  Vickers (HV), Shore (HS) or Leeb (HLD)
- Measurement ranges: HLD 170-960 / HRC 17.9-69.5 / HRB 3.5-101.7 / HB 19-683 / HV
  80-1042 / HS 30.6- 102.6 / HRA 59.1-88
- Accuracy: ±0.5 HLD
- Type D impact device
- Measuring principle: Rebound method
- Includes ISO calibration certificate

Manufacturer: PCE Instruments
£ 509.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-1000N

PCE-1000N is a portable handheld Barcol hardness tester used to measure the hardness of pure aluminum, soft aluminum, thick aluminum alloy and aluminum sheets, strips, rods, castings and forgings. The hardness of fiber-reinforced (FRP) plastics, glass-reinforced (GRP) plastics, hard plastics and soft metals (such as copper or lead) also can be tested using this battery-powered digital Barcol impressor hardness meter.


- Measurement parameters: Barcol (HBA), Brinell (HB), Vickers (HV), Webster
  (HW)
  Rockwell (HRB / HRE / HRF / HRH)
- Measuring range: 0 ... 100 HBA / 25 ... 150 HB
- Accuracy: 81 .. 88 HBA: ± 1 HBA / 42 ... 48 HBA: ± 2 HBA
- Repeatability: 81 .. 88 HBA: ± 1.5 HBA / 42 ... 48 HBA: ± 2.5 HBA
- Resolution: 0.1 HBA

 

Manufacturer: PCE Instruments
£ 511.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-950

PCE-950 is a handheld metal hardness tester used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.


- Hardness units: HL, HRC, HRB, HRA, HB, HV, HS
- Accuracy: ±6 HL at HL = 790
- Impact device: Type D (integrated)
- Maximum hardness: 976 HV
- For use with hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy metals

Manufacturer: PCE Instruments
£ 558.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-900

PCE-900 is a handheld portable Leeb rebound hardness tester used to measure the hardness of metal and steel. This precise and versatile digital hardness tester has a type D impact probe and displays measurements in Leeb (HLD), Rockwell C (HRC), Rockwell B (HRB), Brinell (HB), Vickers (HV) or Shore (HSD) hardness units.


- Measurement range: 200 ... 900 HLD
- Accuracy: ±10 HLD
- Repeatability: ±6 HLD
- 9 common material presets
- Includes factory calibration certificate, lab cert optional

 

Manufacturer: PCE Instruments
£ 564.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-2500

PCE-2500 is a portable, handheld, pen-sized, digital metal hardness tester, rebound hammer or durometer. This hardness tester quickly and accurately measures 10 common metal materials including steel / cast steel, alloy tool steel, stainless steel, lamellar iron, nodular iron, cast aluminum, brass, bronze, wrought copper and forging steel.


- Displays measurements in Rockwell A, B or C (HRA, HRB or HRC), Brinell (HB),
  Vickers (HV), Shore (HS), Leeb (HL) or Strength Value (σb (N/mm2))
- Accuracy: ±2 HL (or 0.3 % @ HL = 800)
- Internal type D rebound mechanism
- Measurement ranges: HL 170-960 / HRC 17-70 / HRB 13-109 / HB 20-665 / HV
  80-940 / HS 32- 99.5 / HRA 30-88 / I?b(rm) 255-2639N/mm2
- Memory size: 360,000 values
- LED display

 

Manufacturer: PCE Instruments
£ 590.00

Price excl. VAT &. delivery
2 year Warranty

Order no.: PCE-AL

Mechanical shore hardness tester for measuring the hardness of soft rubber and plastic. The PCE-AL hardness tester is a standard model for measuring the hardness of rubber (Shore A). The hardness tester is composed of a device with a pressure pin and a 360° anti-glare dial with an accuracy to within 0.5 hardness units. Meets standard ASTM D2240. The hardness tester comes manufacturer calibrated and can optionally be certified to ISO.


- Shore A measurement (long version)
- Force: 1000 g
- Penetrating body: 35°
- Diameter of dial: 57 mm
- Total length: 166 mm
- Follows ASTM D2240

 

Manufacturer: PCE Instruments
£ 631.00

Price excl. VAT &. delivery
2 year Warranty