Current Clamp

Order no.: PCE-PCM 3
With the current clamp AC currents of up to 1000 A AC can be measured easily. At the same time, voltages of up to 1000V AC / DC can be measured with the current clamp. 

Measuring function
- Current measurement AC
- Inrush current AC
- Voltage measurement DC
- Voltage measurement AC
- Frequency measurement
- Frequency measurement current measurement function
- Frequency measurement voltage measurement function
- Duty cycle
- Resistance measurement
- Continuity test
- Capacity measurement
- Diode measurement
- Single-phase power measurement
- Power factor capacitive / inductive
- Harmonics measurement
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DC2-ICA

Current clamp for measuring AC/DC current, AC voltage and resistance. This current clamp is designed to indirectly detect AC/DC current and ohms. The current clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The current clamp comes manufacturer calibrated and can optionally be certified according to ISO or standards.


- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DC3-ICA

Current clamp to determine indirectly, the AC/DC currents with high accuracy.


- AC current (50 / 60 Hz): 2 A  / 1-mA / ± 2.8% + 10 dgt
- DC current: 2 A / 1-mA / ± 3.0% + 10 dgt
- AC overload protection: 100V AC up to 600V AC 50 / 60 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-CM 40-ICA
The flexible current clamp PCE-CM 40-ICA is suitable for current measurements up to 3000 A AC. In addition to TRMS current measurement, the flexible current clamp PCE-CM 40-ICA can be used to measure inrush currents. The measurement of the current takes place via a flexible Rogowski coil. 

- Measuring range up to 3000 A AC
- LC display
- Inrush function
- Frequency measurement
- Data memory
- Incl. ISO Calibration Certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LCT 1-ICA
With the PCE-LCT 1-ICA current clamp it is possible to measure leakage currents in the range of up to 100A. Leakage occurs when a current flows through an electrical conductor that is not normally designed to conduct electricity. The PCE-LCT 1-ICA current clamp captures these currents and displays them on the display. 

- Measurable electrical parameters: AC V, AC A, resistance
- Clamp diameter: 30 mm
- Operating temperature: -10 ... 50°C / 50 ... 122°F
- Current consumption: 10-mA
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DC 41-ICA

The current clamp PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the current clamp, or you can use the integrated clamp mechanism. By using the clamp of the digital current clamp, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.


- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-360

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.


- Voltage range: 50.0 V ... 600.0 V True RMS value
- Current range: 3.0 A ... 999.9 A True RMS value
- Includes clamps, clips, leads, PC software and data cable
- Data logger of 10,000,000 records at 5/10/30/60/120 second interval options
- For measurement in real time and over an extended time period up to 578 days @ 5 second sample rate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PA 8000

With the PCE-PA 8000 Current Clamp you will be able to perform prolonged measurements of electrical properties. The measurement data is saved in xls format on the included SD card to be easily transferred to a computer or laptop for review. The Current Clamp comes manufacturer calibrated and can be certified to ISO or UTIL standards as an option.

- Display: 3.7 in / 94 mm LCD (320 x 240 pixels) with LED backlight
- Electrical properties: AC V, AC A, active power, apparent power, power factor, phase angle, power frequency
- Voltage ranges: 10 V ... 600 V AC, automatic range selection
- Measures current up to 1200 A
- Security / Standards: IEC1010CAT III 600V

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-1

The PCE-830 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-Mini01

Current Clamp for multimeter to 150 A AC, Æ max. 10 mm, different output signals.


- Measuring range: 2 ... 150 A
- Accuracy: 2.5%
- Bandwidth: 48 ... 500 Hz 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini03

Current Clamp for multimeter to 150 A AC, Æ max. 10 mm, different output signals.


- Measuring range: 1 ... 100 A
- Accuracy: 2%
- Bandwidth: 48 ... 500 Hz 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini09

Current Clamp for multimeter to 150 A AC, Æ max. 10 mm, different output signals.


- Measuring range: 1 ... 150 A
- Accuracy: 4%
- Bandwidth: 48 ... 500 Hz 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini05

Current transformers for multimeter to 150 A AC, Æ max. 10 mm, different output signals.


- Measuring range: 0.005 ... 10 A, 1 ... 100 A
- Accuracy: 3%
- Bandwidth: 48 ... 500 Hz 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini02

Current Clamp for multimeter to 150 A AC, Æ max. 10 mm, different output signals.


- Measuring range: 0.05 ... 100 A
- Accuracy: 1%
- Bandwidth: 48 ... 10 Hz 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN08

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. вiameter 20 mm.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN09

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN13

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN10

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets
- Output protected against voltage surges


Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN12

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN11

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer