PCE Instruments

Condition Monitoring

Order no.: PCE-VT 1100S

The PCE-VT 1100S condition monitoring vibration meter is suitable for relative measurements on various machines. With the 45 mm long needle probe, you can access hard-to-reach places in machines and motors. For this reason, this condition monitoring vibration meter is used for rapid measurement of imbalance and for checking bearing and gear conditions.

- Frequency range: 10 Hz ... 1 kHz
- Measures speed, distance, acceleration
- Holds the reading after each measurement
- Handy and battery operated
- Needle probe: 45mm / 1.77"

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VM 31-HA

The PCE-VM 31-HA Condition Monitoring Human Vibration Meter is designed for measuring human vibration at the workplace. The Condition Monitoring Vibration Meter can calculate hand-arm vibration measurements according to ISO 5349 and whole-body vibration measurements according to ISO 2631.


- Measuring of human vibration at the workplace
- Velocity, acceleration, displacement
- 3 channel FFT
- TEDS support
- Includes hand-arm sensor only - whole-body sensor sold separately (see
  accessories)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VM 31-WB

The PCE-VM 31-WB Condition Monitoring Human Vibration Meter or Analyzer is designed for measuring human vibration at the workplace. The Condition Monitoring Vibration Meter can calculate hand-arm vibration measurements according to ISO 5349 and whole-body vibration measurements according to ISO 2631.


- Measuring of human vibration at the workplace
- Velocity, acceleration, displacement
- 3 channel FFT
- TEDS support
- Includes whole-body sensor only - hand-arm sensor sold separately (see   
  accessories)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VM 31-HAWB

The PCE-VM 31-HAWB Condition Monitoring Human Vibration Meter is designed for measuring human vibration at the workplace. The Condition Monitoring Vibration Meter can calculate hand-arm vibration measurements according to ISO 5349 and whole-body vibration measurements according to ISO 2631. Each sensor consists of a triaxial Vibration Meter that captures acceleration, velocity, and displacement measurements.


- Measuring of human vibration at the workplace
- Velocity, acceleration, displacement
- 3 channel FFT
- TEDS support

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VMS 504

The wireless PCE-VMS 504 Vibration Monitor detects vibration within an acceleration range of up to 30 g and a frequency range between 5 and 10 KHz. The wireless vibration monitor therefore features external vibration sensors, which measures vibrations at machines to transfer those wireless to a receiving unit.


- Acceleration range: up to 300 m/s2
- Wireless communication via ZigBee
- Frequency range between 5 Hz and 10 kHz
- Wireless transferring Piezo sensors
- Data memory (receiving base) 128 MB

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LES 300
The Condition Monitoring Tachometer PCE-LES 300 is equipped with 9 high-power LEDs that generate a light intensity of 5100 lux at 6000 FPM at a distance of 20 cm / 7.9 in. This allows the PCE-LES 300 condition monitoring tachometer / stroboscope to provide a large and bright area of illumination.

- Flash frequency up to 120000 FPM
- Accuracy: ± 0.01%
- Adjustable deceleration time
- 9 high-power LEDs
- Phase shift
- Includes ISO factory calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VE 800

PCE-VE 800 is a handheld articulating condition monitoring borescope inspection camera with video recording and image capture functionality. Equipped with adjustable built-in LED lighting on the waterproof camera tip, the PCE-VE 800 condition monitoring  inspection camera features a high interpolated resolution of 200,000 pixels and a large integrated 4.3" LCD for easy viewing and navigation.

 

- Semi-flexible cable with 4-way articulating tip
- 1.5 m / 4.9 ft cable length
- 2.8 mm / 0.11 in cable diameter

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-T237

The condition monitoring tachometer can be used contactless or with mechanical contact. The PCE-T237 condition monitoring tachometer is particularly suitable for recording rotational speeds and speeds on rotating machines and systems (on conveyor belts, motors, belt drives, etc.).


- Contact measurement of rpm via cone adapter
- Contact measurement of m / min via surface wheel
- Robust ABS plastic housing
- Meter count: 0.1 ... 199,999 m

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-T 260
The combination PCE-T 260 is a measuring instrument for use in maintenance, and production. In addition to the stroboscope function, the condition monitoring tachometer-stroboscope also has the option of removing the rotational contacts and measuring temperatures.

- Optical tachometer
- Measuring range: 5 ... 99999 rpm
- Contact tachometer
- Stroboscope LED
- Temperature measurement: Type K, PT 1000, Infrared
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VT 2700

PCE-VT 2700 is a factory-calibrated (certificate included) handheld portable digital battery-powered condition monitoring vibration meter used to measure the radial and axial vibration of industrial machines, equipment and parts such as bearings and gearboxes.


- Frequency range: 9 Hz ... 1 kHz (in 1 kHz mode) / 9 Hz ... 10 kHz
  (in 10 kHz mode) acceleration; 10 Hz ... 1 kHz velocity /
  displacement
- Resolution: 0.1 m/s2 / 0.1 yd/s2; 0.1 mm/s / 0.003 in/s ; 1 µm /
  3.3814e-14 oz ; 1 rpm
- Accuracy: ± 5% of reading + 2 digits
- Factory calibration certificate included

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VDL 16I
The vibration meter PCE-VDL 16I from PCE Instruments measures and stores the relevant measured variables: temperature, relative humidity, air pressure, light as well as acceleration in three axes by means of a vibration sensor. Therefore, this vibration meter is ideal for monitoring vibrations on machines while simultaneously measuring and recording the relevant environmental conditions of the system.


- 3-Axis acceleration up to 1600 Hz
- 2 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87"
- Additional measurement parameters:
  Temperature, Humidity, Air pressure and Light

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VT 2700S

PCE-VT 2700S is a factory-calibrated (certificate included) portable digital battery-powered handheld condition monitoring vibration meter used to measure the radial and axial vibration of industrial machines, equipment and parts such as bearings and gearboxes. The PCE-VT 2700S comes with a special attachment to adapt the probe for handheld use.


- Frequency range: 9 Hz ... 1 kHz (in 1 kHz mode) / 9 Hz ... 10 kHz
  (in 10 kHz mode) acceleration; 10 Hz ... 1 kHz velocity /
  displacement
- Resolution: 0.1 m/s? / 0.1 yd/s?; 0.1 mm/s / 0.003 in/s ; 1 µm /
  3.3814e-14 oz ; 1 rpm
- Accuracy: ± 5% of reading + 2 digits
- ISO calibration certificate included

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DT 63

PCE-DT 63 is a condition monitoring digital handheld optical tachometer, or rotation meter, that can take noncontact measurements of rotational speed. This handheld condition monitoring tachometer features an integrated laser and is ideal for measuring rotational speeds of machines, motors, conveyor belts and other moving parts.


- Measuring range / Resolution: 50 ... 99.99 rpm / 0.01 rpm, 100 ... 9999.9 rpm
  / 0.1 rpm, 10000 ... 99999 rpm / 1 rpm

- Accuracy: ± 0.03% ± 2 digits
- Measuring distance: 50 ... 250 mm / 1.97 ... 9.84 in

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VDL 24I
For this vibration meter PCE-VDL 24I the acceleration sensor is delivered with a sampling rate of 2400 Hz. The sensor measures the acceleration, which is currently acting on it (3 axes), for example shock / vibration. The measurements take place at predetermined (selectable) time intervals.

- 3-Axis acceleration up to 2400 Hz
- 2 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87"
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TH 5

The Condition Monitoring Thermo Hygrometer PCE-TH 5 is a universal temperature / humidity gauge which allows the measurement of both the ambient temperature and the ambient humidity, as well as the determination of the dew point and wet bulb temperature.


- Temperature measuring range: -20 ... 50°C / -4 ... 122°F
- Humidity measuring range: 0 ... 99.9% r.H.
- Resolution: 0.1°C / 0.18°F, 0.1% relative humidity
- Measurement accuracy: ±3% r.H. / ±0.6°C / 1.08°F
- Calculation of dew point and wet bulb temperature

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PI1

This Condition Monitoring Phase Rotation Meter PCE-PI1 has a robust housing with a large LCD display so you can easily and conveniently determine the phase and motor rotation direction. Furthermore, any problems in individual phases, are displayed on the phase rotation meter. The condition monitoring phase rotation meter meets the safety standard CAT III 600 V, IEC 61010.


- Easy operation
- No batteries required
- Robust alligator clips for easy connection
- 3-phase measurements of 40 ... 690 V AC
- Protection class IP 40

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DT 66

PCE-DT 66 is a condition monitoring portable, digital, handheld tachometer, or rotation meter, that can take measurements of rotational speed. This condition monitoring handheld tachometer features mechanical attachments and is ideal for measuring rotational speeds of machines, motors, conveyor belts and other moving parts.


- For taking measurements in contact with moving parts
- Measuring range: 50 ... 19999 RPM
- Accuracy: ± 0.03% / ± 2 digits

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IR 100

PCE-IR 100 is both a infrared non-contact thermometer for measuring surface temperature and a contact thermometer with probe for measuring core temperature of food. This food-grade condition monitoring thermometer allows for quick and easy testing of food surface temperatures without contamination using the infrared sensor, while also offering the possibility of testing food internal temperatures using the food-quality sensor probe.


- Infrared temperature range: -33 ... 220ºC / -27 ... 428ºF
- Probe temperature range: -55 ... 330ºC / -67 ... 626ºF
- Resolution: 0.2ºC / 0.36ºF
- IP 65 ingress protection rating allows hygienic cleaning

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-428-KIT

PCE-428-KIT is a class 2 data-logging condition monitoring noise meter kit that meets IEC 60651:1979, IEC 60804:2000, IEC 61672-1:2013, ANSI S1.4-1983 and ANSI S1.43-1997 requirements. This portable high-accuracy sound level meter has a large easy-to-read illuminated LCD screen that displays the sound pressure level (SPL) numerically and graphically in real time.

- Measuring range: 25 ... 136 db(A)
- A, B, C and Z frequency weightings
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- Adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Kit includes factory calibration certificates (per ISO 9001) and a type 2 / class 2 acoustic calibrator (PCE-SC 42)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-S 41

The PCE-S 41 Condition Monitoring Stethoscope is battery powered and easy to use. This Condition Monitoring Stethoscope can be used for detecting noise in machine components, such as gears, valves, vents, and pumps.


- Frequency range: 100 Hz to 10 kHz
- Headphones, 70 mm long sensor, 290 mm long sensor
- Weight: 240 g, with battery
- Dimensions: 206 x 50 x 32 mm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer