Clamp on Tester

Order no.: PCE-PA 8000

With the PCE-PA 8000 Clamp on Tester you will be able to perform prolonged measurements of electrical properties. The measurement data is saved in xls format on the included SD card to be easily transferred to a computer or laptop for review. The Clamp on Tester comes manufacturer calibrated and can be certified to ISO or UTIL standards as an option.

- Display: 3.7 in / 94 mm LCD (320 x 240 pixels) with LED backlight
- Electrical properties: AC V, AC A, active power, apparent power, power factor, phase angle, power frequency
- Voltage ranges: 10 V ... 600 V AC, automatic range selection
- Measures current up to 1200 A
- Security / Standards: IEC1010CAT III 600V

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PA 8300

The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:


- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC or (Set 2) 30 A ... 3000 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-1

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-2

The PCE-830-2 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-3

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-Mini01

Clamp on Tester for multimeter to 150 A AC, ? max. 10 mm, different output signals. The Clamp on Tester of the mini-series impresses with its compact dimensions. The clamp convertor can be used both for currents up to 150 A and for small currents of a few mA. The Clamp on Tester of the mini-series measures the AC reliably and accurately. All test instruments come manufacturer calibrated -  an ISO certificate can be ordered separately.


- Measuring range: 2 ... 150 A
- Accuracy: 2.5%
- Bandwidth: 48 ... 500 Hz

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini03

Clamp on Tester for multimeter to 150 A AC, ? max. 10 mm, different output signals. The Clamp on Tester of the mini-series impresses with its compact dimensions. The clamp convertor can be used both for currents up to 150 A and for small currents of a few mA. The Clamp on Tester of the mini-series measures the AC reliably and accurately. All test instruments come manufacturer calibrated -  an ISO certificate can be ordered separately.


- Measuring range: 1 ... 100 A
- Accuracy: 2%
- Bandwidth: 48 ... 500 Hz

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini09

Clamp on Tester for multimeter to 150 A AC, ? max. 10 mm, different output signals. The Clamp on Tester of the mini-series impresses with its compact dimensions. The clamp convertor can be used both for currents up to 150 A and for small currents of a few mA. The Clamp on Tester of the mini-series measures the AC reliably and accurately. All test instruments come manufacturer calibrated -  an ISO certificate can be ordered separately.


- Measuring range: 1 ... 150 A
- Accuracy: 4%
- Bandwidth: 48 ... 500 Hz

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini05

Current transformers for multimeter to 150 A AC, ? max. 10 mm, different output signals. The Clamp on Tester of the mini-series impresses with its compact dimensions. The clamp convertor can be used both for currents up to 150 A and for small currents of a few mA. The Clamp on Tester of the mini-series measures the AC reliably and accurately. All test instruments come manufacturer calibrated -  an ISO certificate can be ordered separately.


- Measuring range: 0.005 ... 10 A, 1 ... 100 A
- Accuracy: 3%
- Bandwidth: 48 ... 500 Hz

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-Mini02

Clamp on Tester for multimeter to 150 A AC, ? max. 10 mm, different output signals. The Clamp on Tester of the mini-series impresses with its compact dimensions. The clamp convertor can be used both for currents up to 150 A and for small currents of a few mA. The Clamp on Tester of the mini-series measures the AC reliably and accurately. All test instruments come manufacturer calibrated -  an ISO certificate can be ordered separately.


- Measuring range: 0.05 ... 100 A
- Accuracy: 1%
- Bandwidth: 48 ... 10 Hz

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN08

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN09

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm, The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN13

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN10

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets
- Output protected against voltage surges 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN12

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN11

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN14

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 1 mV / A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN88

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: DC voltage
- Output / input ratio: 100 mV DC/ A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN15

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 1 mV / A AC
- Output: lead and isolated Ø 4 mm male plugs

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN89

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated voltage: 200 A AC
- Output signal: DC voltage
- Output / input ratio: 100 mV DC/ A AC
- Output: lead and isolated Ø 4 mm male plugs

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer