Panel Meter

£ 154.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter can be configured as AC and DC voltmeters (up to 600 Vac / DC), AC and DC ammeters (up to 5 AAC / DC). Furthermore, the built-in display shows measured values of process signals (mA, VDC), thermocouples, resistive temperature sensors (Pt, Ni, PTC and NTC), resistors, potentiometers and frequency.

Input:
2-, 3- wire
Thermocouples
Potentiometer
Resistance
Process signals
Frequency
DC voltage
DC power
AC voltage
AC power

Panel Meter PCE-ND10

£ 160.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is able to perform current, voltage and power measurements in 3-phase systems. By using appropriate transducers, it is also possible to measure high currents and voltages with the panel meter. Thepanel meter was designed for panel-mounting in 92 x 92 mm panel cut-outs.

- Power meter for panel-mounting (92 x 92 mm)
- Measurement of U, I, f, P, Q, S, PF...
- Power supply via voltage input
- Alarm function
** Different variants can be selected! Note: This item must be configured before ordering! **

Panel Meter PCE-N30U

£ 168.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter can process several different input signals, such as 0...410/4010 Ohm, -10...+63 mV DC, -13...+13 V DC, -24...+24 mA DC or signals from thermocouples and resistance thermometers. This makes the panel meter applicable in a wide range of applications. The measured values are shown on the large LED display of the panel meter.

- 21-point scaling
- IP 65 protection on the front
- Three-colored display
- Two alarm outputs

Panel Meter PCE-N30P

£ 181.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter can determine the most important system parameters of a single-phase network. Based on the current and voltage, the panel meter calculates the apparent, active and reactive power, as well as the phase difference angle and the power factor. The panel meter can also determine the average power for a 15 minute period and the average voltage for a 10 minute period.

- Input: 0.02...6 A / 0...480 V / 45.00...100.00 Hz
- Accuracy: 0.2 %
- IP65 protected front
- two alarm outputs

Panel Meter PCE-DPD-F1

£ 286.00

Price excl. VAT &. delivery
2 year Warranty

The built-in display is used to indicate the force and weight, which is detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

- Power supply: 85 ... 265V AC / DC
- Input signal: mV / V for force and weighing sensors
- Display: 6 digits, red
- Digit height : 14 mm

Panel Meter PCE-DPD-F2

£ 297.00

Price excl. VAT &. delivery
2 year Warranty

The built-in display is used to indicate the force and weight, which is determined by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

- Power supply: 11 ... 60V DC / 24/48V AC
- Input signal: mV / V for force and weighing sensors
- Display: 6 digits, red
- Digit height : 14 mm

Panel Meter PCE-NA5

£ 374.00

Price excl. VAT &. delivery
2 year Warranty

The digital panel meter is equipped with a 55-digit bar graph display, which is freely programmable. In addition, the panel meter also comes with a conventional display, which shows the active measuring value as a figure. The panel meter is able to process a large variety of signals.

- 55-digit bar graph display
- 4-digit, 7-segment display
- Analogue output
- Four alarm relays

Panel Meter PCE-G 2

£ 430.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is used to measure the environmental parameters of temperature and humidity. The panel meter is used in warehouses, open-plan offices, schools, etc.

- Measuring range temperature: -40 ... 85 °C

- Measuring range humidity: 0 ... 99 % r.H.

- 55 mm character height

- Up to 30 m reading distance

- External sensor (wired)

Panel Meter PCE-ULM 10

£ 489.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is the ideal measuring device to determine the fill level of a silo. Thanks to the 4 … 20-mA output signal, the panel meter can also be connected to the operational process control.

- Measuring range: 0 ... 10 m / 0 ... 32.8 ft
- Accuracy: 0.5%
- Resolution: 0.001 m
- With display for setting and reading
- Stable M60 connection thread

Panel Meter PCE-N45F

£ 534.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is used to realize individual weighing solutions. The panel meter can be used to connect load cells, force sensors, weighing platforms and other sensors that use strain gauges.

- Signal input range: 0 ... 10 mV / 0 ... 15 mV
- Supply voltage of the measuring cell: 5V
- Power supply: 24V DC
- Relay output
- Potential-free digital input
- Interface and analog output

Panel Meter PCE-N50F

£ 610.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is suitable for panel mounting. This panel meter can be used to indicate the weight, force or torque. The decisive factor here is the type of sensor that is connected to the panel meter.

- Signal input range: 0 ... 20 mV
- Units: g, mN, mlb, Pa, kg, N, Ib, kPa, t, kN, klb, MPa
- For load cells, force sensors, etc.
- Up to 1600 Hz sampling rate
- LCD display

Panel Meter PCE-ULM-10-N24S

£ 623.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is the ideal measuring device to determine the filling level of a silo. Thanks to the 4 ... 20 mA output signal, the panel meter can also be connected to the operational process control.

- Measuring range: 0 ... 10 m / 0 ... 32.8 ft
- Accuracy: 0.5%
- Resolution: 0.001 m
- With display for setting and reading
- Stable M60 connection thread
- incl. external digital display PCE-N24S:
- Voltage supply: selectable
- Input signal: selectable
- Display: 4 digits, red
- Digit height: 20 mm / 0.78"

Panel Meter PCE-BPD-U-46A

£ 667.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is designed in such a way that the measured values displayed can be read from a large distance. With a digit height of 60 mm or 100 mm (2.3" or 3.9"), the reading distance for panel meters is 25 m or 50 m (82 ft or 164 ft).

- Function: convert analog signal into usable value
- Input signal: 4 ... 20 mA, ±20 mA DC, 0 ... 10 V DC, ±10 V DC
- Display range: -1999 ... 9999
- Digit height: 60 mm / 2.3"
- Number of outputs: 2
- Voltage supply: 85 ... 265 V AC / 120 ... 370 V DC

Panel Meter PCE-BPD-U-46D

£ 667.00

Price excl. VAT &. delivery
2 year Warranty

Panel Meter PCE-BPD-C-66D

£ 796.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is designed in such a way that the readings displayed can be read from a long distance. With a digit height of 60 mm or 100 mm (2.3" or 3.9"), the reading distance for the display is 25 m or 50 m (82 ft or 164 ft).

- Function: time measurement
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 11 ... 36 V DC

Panel Meter PCE-BPD-P-66A

£ 796.00

Price excl. VAT &. delivery
2 year Warranty

- Function: convert frequency to a usable value
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 85 ... 265 V AC / 120 ... 370 V DC

Panel Meter PCE-BPD-P-66D

£ 796.00

Price excl. VAT &. delivery
2 year Warranty

- Function: convert frequency to a usable value
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 11 ... 36 V DC

Panel Meter PCE-G1

£ 974.00

Price excl. VAT &. delivery
2 year Warranty

The panel meter is intended for stationary measurement of relative humidity and temperature and direct display on a large display. This panel meter consists of an LED display (100 mm high) and is protected according to IP 54.

- Temperature measuring range: 0 ... +60 °C (Celsius only)
- Humidity measuring range: 10 ... 95 % RH
- Up to 50 m (164 ft) reading distance
- External sensor (wired)