The torque meter for drinking bottles was developed to determine the torque of screw caps on drinking bottles and similar containers in a stationary manner. The software can then be used to depict a graphical and tabular course of the measurement sequence from the torque meter for drinking bottles.

• Measuring range: 10 Nm / 7.4 ft-lb
• Resolution: 0.005 Nm / 0.0037 ft-lb
• Accuracy: 0.3% of the measuring range
• USB interface for software connection
• Integrated printer

The torque meter for drinking bottles was developed to determine the torque of screw caps on drinking bottles and similar containers in a stationary manner. The software can then be used to depict a graphical and tabular course of the measurement sequence from the torque meter for drinking bottles.

• Measuring range: 5 Nm / 3.69 ft-lb
• Resolution: 0.002 Nm / 0.0015 ft-lb
• Accuracy: 0.3% of the measuring range
• USB interface for software connection
• Integrated printer

The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm / 368.78 ft-lb, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.

• Measurement range: 500 Nm (50 kgfm) / 368.78 ft-lb
• Resolution: 1 Nm / 0.738 ft-lb
• Accuracy: ±0.5 % of measurement range
• Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
• Calibration: possible with external F2 weights
• Max. overload: 50 % of measurement range

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

• Measuring range: 10 Nm (1 kgf-m) / 7.38 ft-lb
• Max. 0,5 % accuracy from the measuring range
• Measuring rate freely adjustable up to 1000 Hz
• 24 Bit Processor
• Keyed chuck up to Ø 13 mm

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

• Measuring range: 5 Nm (0,5 kgf-m) / 3.69 ft-lb
• Max. 0,5 % accuracy from the measuring range
• Measuring rate freely adjustable up to 1000 Hz
• 24 Bit Processor
• Keyed chuck up to Ø 13 mm

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

• Measuring range: 2 Nm (0,2 kgf-m) / 1.475 ft-lb
• Max. 0,5 % accuracy from the measuring range
• Measuring rate freely adjustable up to 1000 Hz
• 24 Bit Processor
• Keyed chuck up to Ø 13 mm

The Torque Meter PCE-TM 80 with external sensor to measure the static or startup torque moment in screws, components, switches, transmission shafts, etc. The Torque Meter PCE-TM 80 is an affordable solution to easily calibrate and test static torque measurements.

• Range 0 … 147 Ncm / 0 … 13.01 lbfin
• Selection of  3 units (Ncm, kgfcm, lbfin)
• Digital output RS-232
• External torque sensor
• Measures startup or static torque, not dynamic torque 

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

• Diameter: Ø2.2mm / 0.08"
• Cable length: 1m / 3.2 ft
• Camera direction: 90°
• Resolution: 160,000 pixels
• Focusing range: 5 … 50 mm / 0.19 … 1.96"
• 7" touch screen for easy operation
• replaceable battery with status display
• Storage of recording on SD card
• Motor with endoscope cable can be changed quickly
• HDMI connection for direct image transmission

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

• Endoscope cable length: approx. 2 m / 6.5 ft
• Diameter: 3.8mm / 0.15"
• Camera resolution 160,000 pixels each
• Viewing angle front camera 120°, side camera 90°
• Focusing distance 5 … 50 mm / 0.19 … 1.96" each
• Camera head length: 42 mm / 1.6"
• Bending radius at 90° 35 mm / 1.3"
• Live images from both cameras side by side
• 7" touch screen for easy operation
• Replaceable battery with status display
• Storage of recording on SD card
• Motor with endoscope cable can be changed quickly
• HDMI connection for direct image transmission