£ 20,670.00
Price excl. VAT &. delivery
2 year Warranty
2 year Warranty
The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm / 368.78 ft-lb, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.
- Measurement range: 500 Nm (50 kgfm) / 368.78 ft-lb
- Resolution: 1 Nm / 0.738 ft-lb
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 10 Nm (1 kgf-m) / 7.38 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 5 Nm (0,5 kgf-m) / 3.69 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 2 Nm (0,2 kgf-m) / 1.475 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
PCE-5000 is a portable hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in Non-destructive testing produces microscopic indentation.
- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available
The force gauge PCE-DFG NF 1K with an external load cell is designed for the measurement of compressive forces at hard-to-reach measuring points. The load cell has several threaded holes on the underside that allow a firm installation.
Suitable for determining the humidity of bulk substances, this moisture test instrument can be fitted into containers and systems such as troughs,
bunkers, distributors, augers, conveyors, bins and silos. This permits
24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash
(mineral), wood chips (surface to 5 cm) feed grain, flour, pastes,
seed, or similar bulk or flowing substances. These test instruments / test sensors are mainly for use in manufacturing processes to give the opportunity of process optimization to the manufacturer or to insure the moisture content of the final product.
- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C (+41 ... +176 °F)
- Analog and digital signal output
