This Gas Detector is designed to detect formaldehyde in air. The Gas Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Gas Detector runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Range Formaldehyde: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

Single-Gas Gas Leak Detector warning for gases (for Carbon Dioxide CO₂), / without display / with signal output for sensors in combination with a stationary equipment to detect gases (with ATEX approval).

- Stationary
- For Carbon Dioxide CO₂
- Additional display and alarm station
- ATEX approved

 

The Xgard-1-CL2 is a single-gas Gas Leak Detector used to warn for gases (Chlorine, CL₂, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Chlorine, CL₂, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The Gasmaster GM-4 gas leak detector is a reliable, stationary warning device for gases. To connect a gas sensor, the gas measuring device is optionally supplied with a 4 - 20 mA or an mV signal input. The signal input has two alarm relays with which the gas leak detector can control signal lamps/horns or fans, for example.

- 4 inputs for a gas sensor
- Adaptation of gas sensors: O2, O3, CO, CO2, NH3, H2S
- Various combinations possible
- Event logging
- Large, backlit LCD display
- A/V alarm device max. 24V DC 650 mA
- Gas sensors optional

The gas leak detector is used in various areas of industry. For example, the gas leak detector is used on compressed air, gas, steam and vacuum systems, as well as on refrigeration systems and door seals.

- Working frequency: 40 kHz (± 2 kHz)
- Operating time: >10 hours
- Various attachments
- Color display: 3.5" touch panel TFT
- Soundproof headphones

Single-use Gas Leak Detector Crowcon Clip and Clip+ with 24- or 36-month lifetime / triple alarm-signaling / no service or calibration necessary / self-testing function / CO, H2S or O2.

- Single-use Gas Leak Detector for O₂
- 24 months continuous operation time / detection time
- Optic, acoustic, and haptic alarm
- Adjustable alarm levels
- 0 ... 30 % Vol.

 

The Gas Leak Detector AQ-300 Set EF is a high-precision measuring device for measuring the formaldehyde concentration in our circulating air.

- Range Formaldehyde: 0...10 ppm
- High accuracy and functionality
- Alarm function: "High", "Low", Mute
- Alarm output: Transistor output, 150-mA max
- Low Alarm, High Alarm & Control
- Analog output: 0... 5V
- Location ID: Storage of the measuring location

The Air Quality Meter Gasman-CL₂ is a unique gas meter which protects against a specific gas, inflammable or toxic. The Air Quality Meter warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Air Quality Meter fulfills all the European and international norms, even ATEX and UL standards.

• Non-rechargeable, 1-year battery
• For CL₂ (Chlorine)
• Dust and water resistant - IP 65/67
• 0 ... 5 ppm

With its hydrogen-selective sensor, the gas detector can detect the smallest leaks with a very low leak rate. Containers or lines that do not contain hydrogen can also be checked for leaks with the gas detector if they are filled with test gas containing hydrogen and then checked for leaks.

- High sensitivity: > 2 g / year
- Medium sensitivity: > 15 g / year
- Low sensitivity: > 30 g / year - bar display with traffic light function
- Three adjustable sensitivities
- Semi-rigid probe with a length of 40 cm / 15.7"
- Audible and visual alarm

The Xsafe gas detector is a robust gas sensor for flammable gases in the safe range. The Xsafe gas detector is available in different versions, depending on the gases for which it is to be used. The gas measuring device measures the respective flammable gases with the help of an integrated pellistor.

- Different versions available
- For use in safe areas
- Detection by pellistor
- 3-wire 4 ... 20 mA or mV output

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Diameter: Ø2.8mm / 0.11"
- Cable length: 2m / 6.5 ft
- Camera direction: 0°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The Xgard Type 5 gas leak detector is a robust, explosion-proof gas sensor for flammable gases. The Xgard Type 5 gas leak detector is available in different versions, depending on the gases for which it is to be used. The gas measuring device measures the respective flammable gases with the help of an integrated pellistor.
 
- Different versions available
- Explosion-proof construction with ATEX approval
- Detection by pellistor
- 3-wire 4 ... 20 mA output

The Xgard-1-CO is a single-gas Gas Leak Detector used to warn for gases (Carbon Monoxide, CO, 0 ... 250 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Carbon Monoxide, CO, 0 ... 250 ppm)
- Additional display and alarm station
- ATEX or UL approval

 

With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission