The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

- Measuring range: 5 Nm (0,5 kgf-m) / 3.69 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

 

The WiFi industrial borescope can be connected to a tablet or smartphone using the Android or iOS app. The WiFi industrial borescope impresses with its simple handling and its robust construction. With the flexible, metal braided borescope cable, examinations under adverse operating conditions are possible with the WiFi industrial borescope.

- Cable length: 1000 mm / 3ft 3"
- Movable camera head Ø 4.5 mm
- Image transmission via wifi
- For iOS and Android
- Camera resolution / image sensor: 1024 x 768 Px

PCE-VE 390N is the ideal industrial borescope or snake inspection camera for the analysis of buildings (walls, supports, eaves, gutters, attics, crawl spaces), plumbing (pipes, drains, sewers, wells) and heating, ventilation, air conditioning and refrigeration (HVACR) systems (ducts, furnaces, chimneys, boiler and condenser tubes). The IP68-rated cable of this inspection camera is waterproof and heavy duty, making the PCE-VE 390N well suited for use in tough environments like construction sites and industrial installations.

- Camera head diameter: 28 mm / 1.1"
- Camera cable length: 10 m / 32 ft 9"
- Interface: Mini-USB 1.1 and AV out
- Memory: 8 GB SD memory card (incl.)
- Especially suitable for chimneys, downpipes, ventilation ducts etc.

The closing force transducer is an electronic closing force measuring device for power-operated windows in the motor vehicle sector. Typical areas of application are testing and production in the automotive industry.

- Measuring range: 0 ... 150 N
- Spring stiffness: 10 N/mm
- Accuracy: +/- 3N (0-100N) or +/- 3% (>100N)
- Memory for 100 measurements
- Cable length: 1.5 m / 4.9 ft
- Lithium polymer battery
- Support of relevant standards - 2000/4 EG
- incl. ISO calibration certificate

The closing force transducer is an electronic closing force measuring device for power-operated windows in the motor vehicle sector. Typical areas of application are testing and production in the automotive industry.

- Measuring range: 0 ... 50 N
- Spring stiffness: 2 N/mm
- Accuracy: +/- 3N (0-100N) or +/- 3% (>100N)
- Memory for 100 measurements
- Cable length: 1.5 m / 4.9 ft
- Lithium polymer battery
- incl. ISO calibration certificate

The PCE-TG 300-HT5 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 12mm / 0.47"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

PCE-1000N is a portable handheld Barcol hardness tester used to measure the hardness of pure aluminum, soft aluminum, thick aluminum alloy and aluminum sheets, strips, rods, castings and forgings. The hardness of fiber-reinforced (FRP) plastics, glass-reinforced (GRP) plastics, hard plastics and soft metals (such as copper or lead) also can be tested using this battery-powered digital Barcol impressor hardness meter.

- Measurement parameters: Barcol (HBA), Brinell (HB), Vickers (HV), Webster
  (HW)
  Rockwell (HRB / HRE / HRF / HRH)
- Measuring range: 0 ... 100 HBA / 25 ... 150 HB
- Accuracy: 81 ... 88 HBA: ± 1 HBA / 42 ... 48 HBA: ± 2 HBA
- Repeatability: 81 ... 88 HBA: ± 1.5 HBA / 42 ... 48 HBA: ± 2.5 HBA
- Resolution: 0.1 HBA
- Meets ASTM standards: E140-97; D2583-75; B648-78

 

- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- Up to 1000 V terminal voltage
- Low Ohm measurement
- Direct connection for wallboxes
- Adapter with charging plugs type 1 and type 2
- PE conductor test
- Integrated Schuko socket

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).

The PCE-TG 300-NO5/90 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 10mm / 0.39"
- Sensor at 90° angle
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5 MHz
- Bluetooth

The PCE-TG 300-P5EE is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: P-E: 2 ... 600 mm / 0.07 ... 23.62", E-E: 2.5 ... 100 mm / 0.09 ...3.93"
- Diameter: 10mm / 0.39"
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

The PCE-IVE 330 NDT test instrument or inspection camera is used to diagnose and monitor hard-to-reach areas on vehicles, containers, machinery and equipment. Thanks to the 3 m / 9.8 ft telescopic rod of the NDT test instrument, it is also possible to view areas that are difficult to access. Visual monitoring with the videoscope is supported by the flexible camera head.

 

- Camera length: 320 mm / 12.5"
- Camera diameter: 23 mm / 0.9"
- Flexible camera head
- 8" LCD monitor
- Memory function

PCE-VE 360N is a small-diameter industrial borescope or borescope camera for the non-destructive inspection (NDI) of engines, machines and more. This industrial borescope is an ideal tool for diagnosing issues in hard-to-reach places. The waterproof camera head of this kind of borescope features 3 LED lights with automatic illumination. In addition, digital image magnification or zoom of up to 2 times is available.

 

- 1 m / 3ft 3" camera cable with front camera
- 1 m / 3ft 3" camera cable with 90° side camera
- Diameter camera head: Ø 3.9 mm / 0.15"
- Interface: Mini-USB 1.1 and AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 1 m / 3ft 3"

PCE-IVE 320 is a endoscope, inspection camera, videoscope or industrial borescope that comes with a rigid telescoping pole that extends up to 2.3 m (7.55') in length (3 m long total with camera connection). Plus, the endoscope's 0.3 megapixel camera has a 23 mm (0.91") diameter flexible head with microphone and 12 white LEDs offering adjustable brightness. Includes wheel attachment for under vehicle inspection.

- Telescopic pole extends up to 2.3 m / 7.6 ft
   (3 m /9.8 ft long total with camera connection)
- 12.7 cm / 5" LCD monitor with 800 x 480 pixel resolution
- Video recording capability
- Accommodates SD memory cards from 2 ... 32 GB
- Spare battery to allow all day operation

The PCE-HT 71N Hygrometer Data Logger detects air temperature and humidity and stores readings in its internal memory. The Hygrometer Data Logger has a compact format and a wide memory capacity (up to 32,000 values / 16,000 values for each parameter) and it is mainly used as a Data Logger in fields such as supermarket refrigeration units, refrigerated transport, warehouses, and other temperature controlled environments.

- Measurement range: 0 ... 100% RH / -35 ... 80°C / -31 ... 176°F
- Accuracy: ± 3% RH (20 ... 80%) and  ± 5% / ± 1°C (1.8°F)
- Resolution: 0.5% RH / 0.1°C (0.18°F)
- Memory: Max. 32,000 measurement data (16,000 for each parameter (humidity / temperature))

The PCE-HT 71N Temperature Meter detects air temperature and humidity and stores readings in its internal memory. The Temperature Meter has a compact format and a wide memory capacity (up to 32,000 values / 16,000 values for each parameter) and it is mainly used as a Temperature Meter in fields such as supermarket refrigeration units, refrigerated transport, warehouses, and other temperature controlled environments.

- Measurement range: 0 ... 100% RH / -35 ... 70°C / -31 ... 158°F
- Accuracy: ± 3% RH (20 ... 80%) and  ± 5% / ± 1°C (1.8°F)
- Resolution: 0.5% RH / 0.1°C (0.18°F)
- Memory: Max. 32,000 measurement data (16,000 for each parameter (humidity / temperature))