The PCE-288-R Water Analysis Meter or Redox Meter is a very easy to use meter to measure mV / pH / ºC. In the PCE-228-R Redox Meter, values can be directly stored in the SD memory card (Excel format) or can be directly transferred in real time to a PC or laptop by means of the RS-232 interface.

- Good quality at an affordable price
- SD memory card (1 ... 16 GB)
- Values are directly stored in Excel format in the SD memory card (any
  additional software is required)
- RS-232 interface for real-time data transfer

 

The isolating transformer PCE-P17I is used when signals must be galvanically isolated from each other.

- Galvanic isolation of 0 to 20 mA signals
- Power supply via current loop
- Low installation width

A gloss meter is a tester for determining surface gloss. Thereby, with the glossmeter, spectral reflections of a light beam that hits the surface, are measured. The touch screen allows for easy navigation.

- Measuring geometries: 20° / 60° / 85°
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm

The temperature indicator is a measuring device for stationary measurement of relative humidity and temperature. This temperature indicator consists of an LED seven-segment display with a digit height of 100 mm, which enables you to read it very well even at a distance of up to 50 m.

- Temperature measuring range: 0 ... +60 °C (Celsius only)
- Humidity measuring range: 10 ... 95 % RH
- Up to 50 m (164 ft) reading distance
- External sensor (wired)
- Voltage supply: 230 V AC
- with analogue output 4 ... 20 mA

The temperature meter is a measuring device for stationary measurement of relative humidity and temperature. This temperature meter consists of an LED seven-segment display with a digit height of 100 mm, which enables you to read it very well even at a distance of up to 50 m.

- Temperature measuring range: 0 ... +60 °C (Celsius only)
- Humidity measuring range: 10 ... 95 % RH
- Up to 50 m (164 ft) reading distance
- External sensor (wired)
- Voltage supply: 230 V AC
- with analogue output 4 ... 20 mA

This 12-channel temperature data logger accommodates SD cards up to 16 GB in size. The optional software allows the temperature meter to connect to a PC via USB for direct data transfer and analysis via Microsoft Excel. 

- 12-channel data logger for temperature (°C / °F)
- Works with type K, J, T, E, R and S thermocouple sensors
- Adjustable datalogging interval from 1 ... 3600 seconds per channel

 

The temperature meter has a measuring range of -80 … +70 °C. The temperature meter is therefore suitable for monitoring particularly cold environments.

- Measuring range: -80 ... +70 °C / -112 ... +158 °F
- Measurement accuracy: ± 0.5 °C (-30 ... +70 °C / -22 ... +158 °F)
- Resolution: 0.1 °C
- USB data logger for dry ice
- Data export directly as PDF

A gloss meter is a tester for determining surface gloss. Thereby, with the gloss meter, spectral reflections of a light beam that hits the surface, are measured. The touch screen allows for easy navigation.

- Measuring geometries: 20° / 60° / 85°
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm

A gloss meter is a tester for determining surface gloss. Thereby, with the glossmeter, spectral reflections of a light beam that hits the surface, are measured. The touch screen allows for easy navigation.

- Measuring geometries: 20° / 60° / 85°
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm

This Formaldehyde Meter HFX205-100 is designed to detect formaldehyde in air. The Formaldehyde Meter HFX205-100 shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Formaldehyde Meter HFX205-100 runs with help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Range Formaldehyde: 0…100 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

A gloss meter is a tester for determining surface gloss. Thereby, with the glossmeter, spectral reflections of a light beam that hits the surface, are measured. The touch screen allows for easy navigation.

- Measuring geometries: 20° / 60° / 85°
- Measuring range: 20° : 0 ... 1000 GU / 60° : 0 ... 1000 GU / 85° : 0 ... 160 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm

 

The oxygen meter PCE-WMM 100 consists of a main unit and a remote display. The CO2 and oxygen meter PCE-WMM 100 is used to measure carbon dioxide and oxygen in a fixed location. The oxygen meter PCE-WMM 100 has two relays that can be used to control alarm lights or sounders.

- Measuring range CO2: 0 .... 50000 ppm
- Measuring range O2: 0 ... 30 %
- Measuring range temperature: 0 ... 50 °C / 32 ... 122 °F
- Main and remote unit
- Alarm relay
- 4 ... 20 mA analog outputs
- Acoustic alarm

This Gas Detector is designed to detect formaldehyde in air. The Gas Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Gas Detector runs with help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Range Formaldehyde: 0…100 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

The CO2 analyser PCE-WMM 100 consists of a main unit and a remote display. The CO2 analyser PCE-WMM 100 is used to measure carbon dioxide and oxygen in a fixed location. The CO2 analyser PCE-WMM 100 has two relays that can be used to control alarm lights or sounders.

- Measuring range CO2: 0 .... 50000 ppm
- Measuring range O2: 0 ... 30 %
- Measuring range temperature: 0 ... 50 °C / 32 ... 122 °F
- Main and remote unit
- Alarm relay
- 4 ... 20 mA analog outputs
- Acoustic alarm

The gas detector PCE-WMM 100 consists of a main unit and a remote display. The CO2 gas detector is used to measure carbon dioxide and oxygen in a fixed location. The gas detector has two relays that can be used to control alarm lights or sounders.

- Measuring range CO2: 0 .... 50000 ppm
- Measuring range O2: 0 ... 30 %
- Measuring range temperature: 0 ... 50 °C / 32 ... 122 °F
- Main and remote unit
- Alarm relay
- 4 ... 20 mA analog outputs
- Acoustic alarm

- Digital indicator and vibration sensor for predictive maintenance
- PCE-DPD-U: Universal power supply 18… 265V AC (50 / 60Hz) / DC; 14 mm red 4-digit LED display
- PCE-AC420-210 sensor: Measuring range 0.2 ... 20 mm / s; Linear frequency range (± 3 dB) 10 ... 1000 Hz; Degree of protection IP67