The condition monitoring vibration meter is ideal for maintenance workers to quickly check vibrating parts, machines and systems. This condition monitoring vibration meter shows the vibration acceleration, vibration velocity and vibration displacement directly on the display. The measurement unit can be switched between the metric system and imperial units.

Measuring ranges
- Acceleration: 0.0 - 399.9 m/s² / 0.0 - 15744 in/s²
- Velocity: 0.00 - 399.99 mm/s / 0.00 - 15.74 in/s
- Displacement: 0.000 - 3.9 mm / 0.000 - 0.154 in
- Automatic ISO 10816-3 evaluation
- Colored graphic display
- Incl. ISO calibration certificate

- Measuring range: 0.3 ... 25 μm
- Measuring channel sizes: 0.3, 0.5, 1.0, 2.5, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.3 μm 100% at > 0.45 μm according to JIS
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration
- Ethernet, USB
- Incl. temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Measuring range: 0.3 ... 25 μm
- Measurement channel sizes: 0.3, 0.5, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.3 μm, 100% at > 0.45 μm according to JIS
- Ethernet, USB
- Incl. temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Measuring range: 0.3 ... 25 μm
- Measurement channel sizes: 0.3, 0.5, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.3 μm, 100% at > 0.45 μm according to JIS
- CO2 Sensor: 0 ... 5000 ppm
- Ethernet, USB
- Includes temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Automatic range: 30 ... 130 dB
- Manual range: 30 ... 80 / 50 ... 100 / 80 ... 130 dB
- Resolution: 0.1 dB
- Accuracy: ±1.4 dB
- Memory capacity: 32700 values
- Incl. software for LEQ calculation


Important! The LEQ value is only calculated by the software after the data transfer from the device to the PC or laptop.

PCE-VS12 is a vibration meter, analyzer or sensor condition monitoring switch used to measure RMS value, peak value and frequency domain (FFT) of vibration velocity or acceleration piezoelectrically. This IP67-rated vibration monitoring switch features an external USB port, 8-pin female connector 711 and programmable high pass and low pass filters.

- Frequency range (max.): 0.1 Hz ...10 kHz
- Measuring range: Acceleration = 0.1 ... 1000 m/s², Speed = Frequency-dependent
- Connections: Screw terminals for power supply (5 ... 30V DC) and Micro USB (internal)
- Mounting: M8 stud bolt

The condition monitoring thermometer is a highly accurate 1-channel temperature measuring device. The condition monitoring thermometer is ideally suited to operate various PT-100 sensors and thus for condition monitoring. By using four-wire technology, the response time is particularly fast and accurate.

- Measuring range: -100 ... +400 °C / -148 ... 752 °F
- Accuracy: ± 0.05% + 0.1 °C / 0.18 °F (at 18 to 28 °C / 64.4 ... 82.4 °F) device only
- Resolution: 0.01 °C / 0.018 °F
- PT-100 sensor

- Measuring range: 0.5 ... 25 μm
- Measuring channel sizes: 0.5, 0.7, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.5 μm 100% at > 0.75 μm according to JIS
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration
- Ethernet, USB
- Incl. temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Measuring range: 0.5 ... 25 μm
- Measurement channel sizes: 0.5, 0.7, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.5 μm, 100% at > 0.75 μm according to JIS
- Ethernet, USB
- Incl. temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Measuring range: 1.20 ... 300.0 mm  / 0.04 ... 11.81"
- Accuracy: ±0.5% of measured value + 0.05 mm
- Memory capacity: 1500 measured values
- Calibration reference on housing
- Probe temperature range: -10 ... 60 °C / 14 ... 140 °F

The PCE-DDM 50 weighing hook is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 50 weighing hook is delivered in a protective carrying case and includes two shackles made of heavy-duty steel. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 50,000 kg / 500 kN / 110,231 lbs
- Resolution: 20 kg / 200 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The PCE-DDM 50 Hanging Scales are the ideal tool for weighing big loads and for measuring strong tensile forces. The hanging scales are delivered in a protective carrying case and includes two shackles made of heavy-duty steel. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 50,000 kg / 500 kN / 110,231 lbs
- Resolution: 20 kg / 200 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The PCE-DDM 50 Crane Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 50 Crane Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty steel. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 50,000 kg / 500 kN / 110,231 lbs
- Resolution: 20 kg / 200 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The suspended scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The suspended scale is delivered in a protective carrying case and includes two shackles made of heavy-duty steel. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 50,000 kg / 500 kN / 110,231 lbs
- Resolution: 20 kg / 200 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied with remote control indicator

The force gage is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the tension force gage. Despite the high measuring capacity, these materials enable a compact design with a low weight.

- Measurement range: 50,000 kg / 500 kN / 110,231 lb
- Resolution: 20 kg / 200 N / 44 lb
- Minimum load: 400 kg / 881 lb
- Supplied with remote control indicator

The tension dynamometer is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the tension dynamometer. Despite the high measuring capacity, these materials enable a compact design with a low weight.

- Measurement range: 50,000 kg / 500 kN / 110,231 lb
- Resolution: 20 kg / 200 N / 44 lb
- Minimum load: 400 kg / 881 lb
- Supplied with remote control indicator