Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.

- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.

- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges 

Without a doubt, the main advantage of this handheld cup vane Air Flow Meter is that it doesn't need to be held exactly in the direction of the wind. Air Flow Meter with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane Air Flow Meter, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

Without a doubt, the main advantage of this handheld cup vane air flow meter is that it doesn't need to be held exactly in the direction of the wind. Air flow meter with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane Air flow meter, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h

The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.

- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.

- Output signal: 0 … 10V
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

The air flow meter measures the direction of wind and the results are then output in analogue form. The sensor is compatible with and can be mounted on to a wide variety of available measuring equipment.

- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0 … 360°

The air flow meter measures the direction of wind and the results are then output in analogue form. The sensor is compatible with and can be mounted on to a wide variety of available measuring equipment.

- Output signal: 0 … 10V DC
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0 … 360°

Without a doubt, the main advantage of this handheld cup vane Air Velocity Meter is that it doesn't need to be held exactly in the direction of the wind. Air Velocity Meter with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane Air Velocity Meter, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

The clamp meter PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the clamp meter, or you can use the integrated clamp mechanism. By using the clamp of the clamp meter, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

The clamp on tester PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the clamp on tester, or you can use the integrated clamp mechanism. By using the clamp of the clamp on tester, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

Without a doubt, the main advantage of this handheld cup vane Anemometer is that it doesn't need to be held exactly in the direction of the wind. Anemometer with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane Anemometer, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

The current clamp PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the current clamp, or you can use the integrated clamp mechanism. By using the clamp of the current clamp, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

The digital multimeter PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the digital multimeter, or you can use the integrated clamp mechanism. By using the clamp of the digital multimeter, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

This PCE-ERT 10 earth tester is a handy device which allows fast and easy determination of the earth resistance. The grounding resistance is determined with this earth tester in three measuring ranges up to 2000 Ω using three-wire technology.

- Three-wire measuring method
- Earth resistance is determined in three measuring ranges
- Ground voltage measurement up to 200 V
- Zeroing possible
- Alternating and DC voltage measurement

The electrical tester PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 Ω. To perform a measurement, you can either use the measuring leads, which are included in the package of the electrical tester, or you can use the integrated clamp mechanism. By using the clamp of the electrical tester, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.

- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

Without a doubt, the main advantage of this handheld cup vane Environmental Tester is that it doesn't need to be held exactly in the direction of the wind. Environmental Tester with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane Environmental Tester, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

The PCE-125 series Ford Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a Ford cup is used to determine the kinematic viscosity of fluids. The structure of the Flow Cup Meter is standardized according to ASTM D1200 (Ford). This Flow Cup Meter series features:

- Orifice diameters (Ø inside) of 2.5 mm, 3.4 mm, 4.1 mm or 5.2 mm / 0.10 in,
  0.13 in, 0.16 in or 0.20 in
- Viscosity ranges of 25 ... 120, 49 ... 220, 70 ... 370 or 215 ... 1,413 cSt / mm²/s
- Flow times of 40 ... 100, 25 ... 105 or 20 ... 105 seconds (s)